Search Results

Rapid depletion in fuel resources owing to the low efficiency of current automobiles has been a major threat to future generations for fuel availability as well as environmental health. Advanced new generation of internal combustion (IC) engines are expected to have far better emissions levels both gaseous (NOx and CO) and particulate matter, at the same time having far lower fuel consumption on a wide range of operating condition. These criteria could be improved having a homogeneous combustion process in an engine. Homogeneous mixing of fuel and air in HCCI leads to cleaner combustion and lower emissions. Since peak temperatures are significantly lower than in typical SI engines, NOx levels and soot are reduced to some extent. Because of absence of complete homogeneous combustion but quasi homogeneous combustion present in HCCI, there is still a possibility of further reducing the emissions as well as enhancing the engine performance.

Turboexpansion is a concept which is aimed at reducing the fuel consumption of pressure-charged combustion engines by providing over-cooled air to the engine prior to its induction in the combustion chamber. The performance of the engine is dependent on intake charge density which is preferred to be high at reduced charge air temperature. This becomes achievable through a cooling system known as a turbo expander which expands a high-pressure gas to produce work that is usually employed to drive a compressor. Though, initially used for the purpose of refrigeration in industries, for the past few decades various researches have proved its efficiency in internal combustion engines. In gasoline engines, it is usually employed to extend the knock limit and reduce carbon emissions. Also, an extension to the knock limit allows several improvements in parameters such as increased specific output, an increase in compression ratio and a reduction in the fuel consumption of the engine.

Non-edible vegetable oils have a huge potential for biodiesel production and also known as second generation feedstock’s. Biodiesel can be obtained from edible, non-edible, waste cooking oil and from animal fats also. This paper focuses on production of biodiesel obtained from mixture of sesame (Sesamum indicum L.) oil and neem (Azadirachta indica) oil which are easily accessible in India and other parts of world. Neem oil has higher FFA content than sesame oil. Biodiesel production from neem oil requires pretreatment neutralization procedure before alkali catalyzed Trans esterification process also it takes large reaction time to achieve biodiesel of feasible yield. Neem oil which has very high FFA and sesame oil which has low FFA content are mixed and this mixture is Trans esterified with no pre-treatment process using molar ratio of 6:1.Fuel properties of methyl ester were close to diesel fuel and satisfied ASTM 6751 and EN 14214 standards.

Ever increasing consumption of petroleum derived fuels has been a matter of grave concern due to rapidly depleting global reserves and alarming levels of emissions leading to global warming and climate change. Exhaustive research has been carried out globally to evaluate the suitability of variety of renewable fuels for internal combustion engine applications. Amongst them, vegetable oil methyl esters or biodiesel seem to be a promising alternative for diesel in vital sectors such as transportation, industrial and rural agriculture. For quite some time, the focus for production of biodiesel has shifted towards non-edible oil feedstock from the edible ones, mostly due to food security issues. One such non-edible oil, locally known as Mahua in Indian subcontinent, is a very promising feed stock for biodiesel production. In the present investigation, 5%, 10%, 15% and 20% (v/v %) blends of mahua oil methyl ester (MOME) and diesel were prepared.

The interest of using alternative fuels in diesel engines has been accelerated exponentially due to a foreseen scarcity in world petroleum reserves, increase in the prices of the conventional fossil fuels and restrictions on exhaust emissions such as greenhouse gases from internal combustion (IC) engines initiated by environmental concerns. The constant trade-off between efficiency and emissions should be in proper balance with the conventional fuels in a fuel design process for future combustors. Unlike gasoline and diesel, alcohols act as oxygenated fuels. Adding alcohols to petroleum products allows the fuel to combust properly due to the presence of oxygen, which enhances premixed combustion phase, improves the diffusive combustion phase which increases the combustion efficiency and reduces air pollution. The higher activation energy of alcohols leads to better resistance to engine knocking that allows higher compression ratios and greater engine thermal efficiencies.

Concerns about long term availability of petroleum based fuels and stringent environmental norms have been a subject for deliberations around the globe. The vegetable oil based fuels and alcohols are very promising alternative fuels for substitution of diesel, reduce exhaust emissions and to improve combustion in diesel engines which is mainly possible due to oxygenated nature of these fuels. Jatropha oil is important non-edible oil in India which is either used in neat or modified form as diesel fuel. Furthermore n-butanol is renewable higher alcohol having properties quite similar to diesel fuel. In the present study, n-butanol was blended in Jatropha Oil (JO) and Jatropha Oil Methyl Ester (JME) on volumetric basis (10 and 20%). The blends were homogeneous and stable and there was no phase separation. The different physicochemical properties of blends were evaluated as per relevant standards.

India possesses only 0.3% of world petroleum reserves and hence heavily dependent upon petroleum derived fuels to feed its rapidly growing economy. Diesel Engines due to their superior performance have wide application in India, however, they also pollute environment significantly. Research is underway in India and elsewhere to explore the potential of variety of alternative fuels which could substitute diesel in a holistic manner. And in this context, non-edible vegetable oils are very promising as India has a large area of degraded land where such crops could be raised without compromising food security. Large number of studies have suggested that vegetable oils are not suitable in neat form as a fuel in diesel engine and should be trans-esterified using either methanol or ethanol to form esters to bring their properties similar to diesel fuel.

Increased dependency on fossil fuels has led to its depletion as well as affected the environment adversely. Moreover, increasing crude oil prices is pressurizing vehicle manufacturers to invent new technology so as to increase fuel economy and at the same time to keep emissions under control. Hydrogen has gained popularity not just in terms of being an abundant alternative but also due to being a very clean propellant. In the present investigation, hydrogen boosting has been performed on an SI engine running on gasoline-methanol and ethanol-gasoline blends to determine the additional advantages of the same compared to pure gasoline operation. The engine selected for experimental analysis is a single cylinder, air cooled spark ignition engine that has been modified for hydrogen injection in the intake manifold prior to the port with the injection timing being held constant throughout the experiment.

The continued reliance on fossil fuel energy resources is not sufficient to cater to the current energy demands. The excessive and continuous use of crude oil is now recognized as unviable due to its depleting supplies and elevating environmental degradation by increased emissions from automobile exhaust. There is an urgent need for a renewable and cleaner source of energy to meet the stringent emission norms. Hythane is a mixture of 20% hydrogen and 80% methane. It has benefits of low capital and operating costs and is a cleaner alternative than crude oil. It significantly reduces tailpipe emissions and is the cheapest way to meet new emission standards that is BS-IV. Hythane produces low carbon monoxide (CO), carbon dioxide (CO2) and hydrocarbons (HC) on combustion than crude oil and helps in reduction of greenhouse gases.

The world today is facing the effect of the dependence on fossil fuels. Also, the rate of consumption of Fossil derived fuels is alarming. The use of non-conventional energy sources is to be increased so as to tackle the global climatic changes, environmental pollution and also to lower down the rate of depletion of fossil fuels. The urgent need to replace the petroleum products having harmful emissions has leaded us to the Biodiesel. Biodiesel is a well-known alternative for diesel with an advantage over the later because of its biodegradable, less toxic nature, superior lubricity, better emission characteristics and in a way environment friendly. The present study focuses on the comparative study and analysis of performance and emission characteristics of a light duty diesel engine on blends of Fish oil Biodiesel in Diesel and Calophyllum Inophyllum Oil Biodiesel in Diesel.

The present world scenario faces a serious threat from increasing dependence on fossil fuels. This has triggered the awareness to find alternative energy as their sustainable energy sources. Biodiesel as a cleaner renewable fuel may be considered as a good substitution for diesel fuel due to it being used in any compression ignition engine without any modification. The main advantages of using biodiesel are its renewability and better quality of exhaust gas emissions. In terms of emissions from biodiesel, the cause of concern continues to be the NOx emissions. Therefore, to compliment the functioning of biodiesels, Urea-SCR over Cu-ZSM5 catalyst is an effective option due to its ability to convert NOx into nitrogen and water. There has been increasing concerns that biodiesel feedstock may compete with food supply in the long term. The recent paper focuses on use of two non-edible oils mahua oil and fish oil (processed from waste produced by fish).

The commercial sources of energy such as fossil fuels and petroleum products are extensively used. These sources are finite and cause large scale degradation of environment. The increased pollution in urban areas is already causing serious sociological, ecological and economic implications. Diesel engines produce high torque at low rpm as compared to spark ignition engines due to which they are used in industrial, agricultural and transportation sector. Diesel fuel has higher HC, CO and PM emissions in comparison to biodiesel. This has drawn the attention of world towards the usage of biodiesel as an alternative fuel. Biodiesel has an advantage over diesel fuel because of its biodegradable and less toxic nature and superior lubrication properties. However, NOx emissions are compounded in case of biodiesel in CI engine. There has been concerns that biodiesel feedstock may compete with food supply in the long term.

For the last decade, the lubricant industry has been trying to formulate biodegradable lubricants with technical characteristics superior to those based on petroleum. A renewable resource, mahua oil, is good alternative to mineral oil because of its environmentally friendly, non toxic and readily biodegradable nature. The triacylglycerol structure of mahua oil is amphiphilic in character that makes it an excellent candidate as lubricant and functional fluid. It is also very attractive for industrial applications that have potential for environmental contact through accidental leakage, dripping or generates large quantities of after-use waste materials requiring costly disposal. Vegetable oil in its natural form has limited use as industrial fluids due to poor thermo-oxidation stability, low temperature behavior and other tribochemical degrading processes.

The purpose of the OBIGGS is to reduce the amount of oxygen in the fuel tank to a 'safe' level to significantly reduce the possibility of ignition of fuel vapors. There are circumstances where equipment of OBIGGS like ASMs, Ozone Converter Catalysts, etc. gets degraded earlier than the provided MTBF. This paper studies the present conventional systems limitations, like due to memory constraints only the faults and limited shop data are being recorded, hence there is no provision to store/report the stream of data margins with which we can pass/fail the performance tests. This paper also explains how a new design of the Connected concept achieves access to real-time data from the system and how the data is pushed to the cloud network.

Side door latches in an automotive play a major role in occupants’ safety. The latches consist of both retention assembly and actuator assembly. The actuator assembly majorly consists of motor, gear & other components and these are protected through a Plastic Lower case and Housing. The Lower case (over-mold) with the Electrical Component Carrier - ECC (pre-mold) plays an important role in providing electrical power supply to the latch system. Since these parts are manufactured with terminal traces & plastics, upfront mold flow simulations help the product teams to evaluate the short fills, warpage, and other quality aspects in the critical areas of these components. In the part assembly station, the ECC (pre-mold) and the Lower case (over-mold) are connected to the Motor on one side and the Connector on the other. The proper alignment of the pre-mold pins is of great importance and the pre-mold must not be externally visible once the molding is complete.

Wind energy is clean and renewable source of energy that is an attractive alternative to non-conventional sources of energy. Due to rapid increase in global energy requirements, this form of energy is gaining its share of importance. Unlike nuclear power or tar sand oils, wind energy does not leave a long-term toxic legacy. Using MATLAB algorithms, multi-optimization of wind turbine design can be achieved. Therefore, an aerodynamic mathematical model is developed to obtain the optimal chord length and twist angle distribution along the blade span. Further, a promising generic blade design is used to initialize a detailed structure optimization wherein leading edge panel (LEP), Spar cap, Shear web, Trailing edge panel (TEP) reinforcement are sized using composite laminates so that the blade is according to the intended design standard. Initially blade airfoils are analyzed on 2D platform and then the results are used to construct 3D model of Horizontal Axis Wind Turbine (HAWT) blade.

The danger posed by climate change and the striving for securities of energy supply are issues high on the political agenda these days. Governments are putting strategic plans in motion to decrease primary energy use, take carbon out of fuels and facilitate modal shifts. Man's energy requirements are touching astronomical heights. The natural resources of the Earth can no longer cope with it as their rate of consumption far outruns their rate of regeneration. The automotive sector is without a doubt a chief contributor to this mayhem as fossil fuel resources are fast depleting. The harmful emissions from vehicles using these fuels are destroying our forests and contaminating our water bodies and even the air that we breathe. The need of the hour is to look not only for new alternative energy resources but also clean energy resources. Hydrogen is expected to be one of the most important fuels in the near future to meet the stringent emission norms.

The transportation sector faces great and urgent challenges, including climate impacts of greenhouse gas emissions, local health impacts of criteria pollutants, and political & economic impacts of petroleum dependence. While several revolutionary solutions are being developed to reduce the impact of motor vehicles, such as increased fuel economy standards and accelerated adoption of hybrid vehicles, revolutionary new approaches must also be evaluated. One such opportunity is found in Compressed Air Engine (CA Engine), which is powered solely by compressed air stored in a vehicle on-board pressurized tank. Proponents of this technology claim CA Engines are greener and cheaper to operate, since they do not consume fossil fuels and produce zero tail-pipe emissions, while offering the power and performance needed for light-duty vehicle use.

Recent scenario of fossil fuel depletion as well as rising emission levels has witnessed an ever aggravating trend for decades. The solution to the problems has been addressed by investments and research in the field of fuels; such as the use of cleaner fuels involving biodiesel, alcohol blends, hydrogen and electric drivelines, as well as improvement in traditional technologies such as variable geometry systems, VVT load control strategies etc. The developments have highlighted the enormous potential present in such systems in terms of maximizing engine efficiency and emission reductions. The present paper aims at designing and implementing an intake runner system for a CI engine capable of providing flexibility with variations in operating conditions. Primarily, the design aims at altering the air flow phenomenon within the primary intake of the engine by inducing swirl in the runner through a secondary runner.

In the present study, ethanol was added in lower proportions to non-edible vegetable oil “Schleichera oleosa” or “Kusum”, to evaluate various performance and emission characteristics of a single cylinder; diesel engine. For engine's trial, four samples were prepared with 5%, 10%, 15% and 20% ethanol in kusum oil (v/v) and the blends were named as E5K95, E10K90, E15K85 and E20K80 respectively. Neat Kusum oil was named as K100. The results indicated that brake thermal efficiency (BTE) was found to increase with increase in volume fraction of ethanol in the kusum oil. E5K95, E10K90, E15K85 and E20K80 test fuels exhibited maximum BTE of 25.4%, 26.4%, 27.4% and 27.7% respectively as compared to 23.6% exhibited by the neat Kusum oil. Similarly, full load brake specific energy consumption (BSEC) decreased from 16.3MJ/kWh in case of neat Kusum oil to 15.1MJ/kWh for E20K80 with an almost linear reduction pattern with increased ethanol composition in the test fuel.