Search Results

Ceramic preconverters have become a viable strategy to meet the California LEV and ULEV standards. To minimize cold start emissions the preconverter must light-off quickly and be catalytically efficient. In addition, it must also survive the more severe thermomechanical requirements posed by its close proximity to the engine. The viability of the ceramic preconverter system to meet both emissions and durability requirements has also been reported recently(1,2). This paper further investigates the impact preconverter design parameters such as cell density, composition, volume, and catalyst technology have on emissions and pressure drop. In addition, different preconverter/main converter configurations in conjunction with electrically heated catalyst systems are evaluated. The results demonstrate that ceramic preconverters substantially reduce cold start emissions. Their effectiveness depends on preconverter design and volume, catalyst technology, and the system configuration.

The shape and size of the unit cell of a ceramic monolith have a profound influence on its geometric and mechanical properties. These, in turn, affect the catalytic performance, converter durability and vehicle drive-ability. This paper presents the important relationships between cell geometry and monolith's open frontal area, geometric surface area, hydraulic diameter, bulk density, structural rigidity, strength and heat transfer characteristics of the monolith; both the square and triangular cells are considered. These relationships provide a rational basis for selecting the cell shape and size which will yield the best balance between the various performance requirements, i.e. light-off characteristics, conversion efficiency, back pressure and long-term dutability. It is shown that certain tradeoffs are necessary in selecting the final cell geometry which is best accomplished by prioritizing the various performance requirements.

Stringent emissions standards with 95+% conversion efficiency requirements call for advanced ceramic catalyst supports with thinner walls, higher cell density and optimum cell shape. The extrusion technology for cellular ceramics has also made significant progress which permits the manufacture of advanced catalyst supports. Similarly, modifications in cordierite chemistry and the manufacturing process have led to improved microstructure from coatability and thermal shock points of view. The design of these supports, however, requires a systems approach to balance both the performance and durability requirements. Indeed as the wall gets thinner, the contribution of washcoat becomes more significant in terms of thermal mass, heat transfer, thermal expansion, hydraulic diameter and structural stiffness - all of which have an impact on performance and durability. For example, the thinner the wall is, the better the light-off performance will be.

The large frontal area cordierite ceramic flow-through converter for diesel emissions must meet the 290K vehicle mile durability requirement, almost a six fold increase over that of automotive converters. This paper compares the size, the geometry and the operating conditions of automotive vs. diesel converters and suggests ways to design the converter system to meet the challenging durability requirements without compromising its performance with respect to back pressure and conversion efficiency. It is shown that the mechanical durability of the system, which is critical for meeting the 290K vehicle mile durability, can best be met by ensuring good compatibility between the substrate and washcoat and by designing a rugged packaging system with positive mounting pressure under all driving conditions.

An important element of the diesel filter assembly is a resilient ceramic mat placed between the ceramic filter and the stainless steel can. It has four key functions: i) to provide adequate gripping pressure, ii) to permit free axial expansion of can, iii) to act as a seal for gases, and iv) to minimize temperature gradients in the filter, which require certain mat properties, namely low-to-medium compression modulus, low shear modulus, and low friction coefficient between mat and filter. This paper compares the properties and performance of two different mats, Interam® I and III, in “hot shake” and “exhaust gas simulator” tests. The results indicate that Interam® III is a superior material for diesel filter application and that a complete coverage by this mat will prolong the durability of the filter.

The stringent emissions standards in the late 1990's like NLEV, ULEV and SULEV have led to major modifications in the composition and design of ceramic substrates. These changes have been necessitated to reduce cold start emissions, meet OBD-II requirements, and to ensure 100,000 mile durability requirement in a cost-effective manner. This paper presents the key advances in ceramic substrates which include lower thermal expansion, lighter weight, higher surface area and improved manufacturing process all of which help meet performance requirements. In addition to above benefits, the compressive and tensile strengths of lightweight substrates, as well as their thermal shock resistance, are found to be adequate following the application of high surface area alumina washcoat. The strength properties are crucial for ensuring safe handling of the substrate during coating and canning and for its long term mechanical durability in service.

The motorcycle emissions regulations for both two-stroke and four-stroke engines, which are receiving worldwide attention, will go into effect in the very near future. To meet these regulations, the motorcycles will require a catalyst in conjunction with the muffler due to space limitations. The combination of high engine speeds, high vibrational acceleration, high HC and CO emissions, high oxidation exotherms, and stringent durability requirements, points to cordierite ceramic substrate as an ideal catalyst support. However, as an integral unit within the muffler, its packaging design must be capable of withstanding isothermal operating conditions which may exceed the upper intumescent temperature limit of the ceramic mat. This paper describes a durable packaging design for the ceramic catalyst which employs a hybrid ceramic mat, special end rings and gaskets, and high strength stainless steel can.

The dynamic fatigue data for two different cordierite ceramic wall-flow diesel filter compositions, EX-54 and EX-66, are obtained at 200° and 400°C using the 4-point bend test. These compositions offer larger mean pore size and experience lower pressure drop than the EX-47 composition, and hence are more desirable for certain applications. Their fatigue behavior in the operating temperature range is found to be equivalent or superior to that of EX-47 composition which helps promote filter durability. The fatigue data are used to arrive at a safe allowable stress, which would ensure the required 290K vehicle mile durability. The paper also discusses the impact of mean pore size on high temperature strength and fatigue properties and their effect on filter durability.

Preconverters and close-coupled main converters are viewed as key components in advanced emission systems to help the auto industry comply with tightened emission regulations in North America and Europe. Due to their close position to the exhaust manifold when compared to current main catalysts, the mechanical and thermal durability requirements on such close-coupled converters are significantly increased. A set of representative preconverter systems, with respect to back pressure and surface area, ceramic and metal substrate material was exposed to a 100 hour engine aging cycle, which is equivalent to approximately 80,000 kilometers under European driving conditions. This aging cycle is used by the German Autoconsortium (ZDAKW). In order to address the high thermal load in a close-coupled position, the preconverter inlet gas temperature has been elevated to a maximum of 950 °C at stoichiometry. Maximum preconverter midbed temperature has been found close to 1000 °C.

Tempered float glass is commonly used for both side windows and backlites in the automotive industry. The success of such products is primarily attributed to high level of residual compression, following tempering, which provides abrasion resistance as well as 3X higher functional strength to sustain mechanical, vibrational and thermal stresses during the vehicle's lifetime. Certain applications of tempered glass, however, require mounting holes whose surface-finish must be controlled carefully to withstand transient tensile stresses during tempering. Simultaneously, the nature and magnitude of residual compression at the hole must provide sufficient robustness to bear mounting, vibrational and thermal stresses throughout the life of the vehicle. This paper presents (i) analysis of residual compression at the hole, (ii) measurement of biaxial strength of annealed glass with hole at center, and (iii) measurement of biaxial strength of tempered glass with hole at center.

An approximate analytical solution for stress distribution in the rectangular lens of a glass headlamp due to static and impact loading is presented. Both low mass/high velocity and high mass/low velocity impact data and the resulting failure modes are discussed. Generally, glass headlamp lenses break either due to Hertz stress (front surface under high localized tension), or due to flexural stress (back surface under tension due to bending), or the combination of two. Failure due to flexural stress is illustrated by a star-crack, while that due to Hertz stress is illustrated by a Hertzian cone or “bullet hole” in the lens. The failure mode during low mass/high velocity impact is predominantly Hertzian while that during high mass/low velocity impact is flexural for lenses 0.120″ to 0.150′ thick. No significant differences are observed in the impact resistance of standard and light-weight lenses in this thickness range.

High temperature modulus of rupture (MOR) data, published previously, show that the ceramic catalyst supports get stronger with temperature due to the absence of water vapor and closure of microcracks which would otherwise act as stress concentrators [1, 2 and 3]*. The increased MOR value is partially responsible for the excellent durability of ceramic catalyst supports at high temperature. In this paper, we will present the compressive strength data of ceramic substrates at high temperature, namely the crush strength along B-axis and biaxial compressive strength of the whole substrate. Since the honeycomb strength is directly related to that of the individual cell wall, the compressive strength should also increase with temperature similar to the modulus of rupture. Accordingly, the ceramic substrates are capable of supporting higher mounting pressures exerted by the intumescent mat at high temperature [4].

The high temperature creep data for radial specimens, cut from metal and ceramic substrates and subjected to compressive loads representative of mounting and thermal pressure are presented as function of load and temperature. These data show that the creep resistance of metallic specimens under sustained loading varies with temperature and is orders of magnitude lower than that of ceramic specimens. The observed creep deformation in metallic specimens reduces their open frontal area and hydraulic diameter with potentially adverse impact on pressure drop across the metallic substrate.

The high temperature dynamic fatigue data for the catalyst support composition, EX-20, 400/6.8, are presented. These data indicate that the fatigue effects are more severe when the substrate temperature in the peripheral region is near 200°C. The major impact of high temperature fatigue is the slow degradation of substrate’s initial strength while in service. Such a degradation must be taken into account in designing the total converter package to meet life requirements. For the EX-20, 400/6.8 substrate, approximately 50% of its initial strength is available to withstand the combined stresses from mechanical, thermal, and vibrational loads in service. At temperatures well above 200°C, the available design strength can be as high as 65% of substrate’s initial strength. The fatigue theory, the measurement technique, and the application of fatigue data to long term durability of cordierite substrates are discussed.

Under certain operating conditions when the combined stresses in a ceramic wall-flow diesel filter from mechanical, thermal, and vibrational loads exceed its threshold strength, the fatigue effects become important. This paper reviews the theory of static and dynamic fatigue, and presents fatigue data for Coming's high efficiency filter composition (EX-47, 100/17) in the temperature range 25° - 400°C which is representative of the stressed peripheral region during regeneration. The measurement and analysis of fatigue data, together with the implication on long-term durability of cordierite ceramic filters, is discussed.

The high temperature strength and deformation behavior of ceramic and two different metal substrates were measured in the 25°-1200°C temperature range in uniaxial and biaxial bending using rectangular bars and circular discs, respectively, prepared from the substrates. The data show that both of the metal substrates exhibit permanent deformation and lose their load carrying capability by an order of magnitude above 800°C. The ceramic substrate, on the other hand, preserves its strength and behaves elastically over the entire temperature range exhibiting neither permanent deformation nor cell distortion. These data suggest that the upper use temperature for metal substrates could be significantly lower than that for ceramic substrates to meet 50-100K vehicle mile durability

The dual requirement of high conversion efficiency and 50K mile durability for cordierite ceramic converters is achievable through optimization of washcoat and catalyst formulation. This paper presents new data for high temperature physical properties, light-off performance, conversion efficiency and pressure drop through an oval cordierite ceramic converter with triangular cell structure and two different washcoat formulations; namely standard vs high-tech. Both of the washcoat systems have a beneficial effect on strength properties with nominal impact on thermal shock resistance. Both the standard and high-tech catalysts provide identical light-off performance for CO, HC and NOx conversion. The high-tech washcoat and catalyst system, in particular, provides consistently superior conversion efficiency for CO, HC and NOx. The pressure drop across the catalyst depends on hydraulic diameter and is only 8% higher for high-tech washcoat than for standard washcoat.

The isostatic strength of porous cordierite ceramic monoliths plays an important role during canning and subsequent operation of automotive catalysts. Its value depends on wall porosity, cell geometry, skin thickness and morphology, monolith size and contour, and substrate/washcoat interaction. If the stresses induced by canning loads and closure speeds exceed the isostatic strength, the monolith may exhibit either crushing or shear type failure. This paper presents the room temperature isostatic strength data for coated and uncoated ceramic monoliths of different contour, size, and cell geometry. The applied isostatic load on the monolith is translated into stresses in the porous cell wall using both an analytical model and finite element analysis. It is found that the failure criteria are governed by the fundamental tensile and compressive strengths of the cell wall.

Ceramic honeycomb structures have been used successfully as catalyst supports in gasoline-powered vehicles for the past ten years. They are currently the leading candidate for trapping and oxidizing the carbonaceous particulate emissions in diesel-powered vehicles. In both of these applications the long term durability of the ceramic substrate is of prime importance. This, in turn, depends on the physical properties of cellular structure, cyclic nature of service loads and design of the mounting assembly. This paper examines the nature and dependence of both the mechanical and thermal stresses in the substrate on its geometry, properties, mounting parameters, and the operating conditions. It also compares the observed failure modes with those predicted by the theory. The paper concludes with a set of recommendations for optimal systems design and acceptable operating conditions which will promote the long term durability of the ceramic substrate.

The stringent durability requirements approaching 100,000 vehicle miles for automotive substrates and 290,000 vehicle miles for large frontal area diesel substrates for 1994+ model year vehicles call for advanced packaging designs with thick ceramic mats and high mount densities. The latter result in high mounting pressure on the substrate and enhance its mechanical integrity against engine vibrations, road shocks and back pressure forces. A novel measurement technique which applies a uniform biaxial compressive load on the lateral surface of ceramic substrates, thereby simulating canning loads, is described. The biaxial compressive strength data obtained in this manner help determine the maximum mounting pressure and mat density for a durable packaging design. The biaxial compressive strength data for both round and non round substrates with small and large frontal area are presented.