Search Results

A simulation model of the Hybrid III lower extremities with the 30 degree dorsiflexion ankle was developed using the CVS/ATB program. The femur and tibia were modeled as a sequence of rigid beams with a hinge and slider at the knee. Special, locked joints were placed in the femur and tibia at the same locations as the load cells in the actual dummy. Constraint forces and moments at these joints can be compared directly to load cell data. The complex geometry of the foot was divided into five segments representing the heel, toe, forefoot, midfoot, and ankle regions. Two foot models were constructed: one barefoot and one with a Lehigh safety shoe. Good agreement was obtained for most parameters when single-leg pendulum tests, and full-body sled tests, were simulated using the new model.

In a previous experimental study, a comparison was made between a 1978 Pontiac LeMans car front with a standard bumper and the same front with a more compliant bumper developed by the National Highway Traffic Safety Administration (NHTSA). The tests were made with the two car front and bumper systems mounted at the normal bumper level 45 cm and with a lower front configuration with the bumper level 32.5 cm above the ground. The experimental biological model system developed at Chalmers University of Technology for detailed kinetic analysis of car front to leg impact sequences was used for this comparison. The tests were carried out at 30 to 32 km/h impact speed. A significant difference was found only between the standard bumper in the higher position and the compliant bumper in the lower position. A still more compliant bumper than that used in the previous test series was produced by NHTSA and tested with the front and bumper system in the normal position 45 cm above the ground.

The air bag has proven effective in reducing fatalities in frontal crashes with estimated decreases ranging from 11% to 30% depending on the size of the vehicle [IIHS-1995, Kahane-1996]. At the same time, some air bag designs have caused fatalities when front-seat passengers have been in close proximity to the deploying air bag [Kleinberger-1997]. The objective of this study was to develop an accurate and repeatable out-of-position test fixture to study the deployment of air bags into out-of-position occupants. Tests were performed with a 5th percentile female Hybrid III dummy and studied air bag loading on the thorax using draft ISO-2 out-of-position (OOP) occupant positioning. Two different interpretations of the ISO-2 positioning were used in this study. The first, termed Nominal ISO-2, placed the chin on the steering wheel with the spine parallel to the steering wheel.

A new lower extremity has been developed to be used with Thor, the NHTSA Advanced Frontal Dummy. The new lower extremity, known as Thor-Lx, consists of the femur, tibia, ankle joints, foot, a representation of the Achilles' tendon and the associated flash/skins, it has been designed to improve biomechanical response under axial loading of the femur during knee impacts, axial loading of the tibia, static and dynamic dorsiflexion, static plantarflexion and inversion/aversion. Instrumentation includes a standard Hybrid ill femur load cell, accelerometers, load cells, and rotary potentiometers to capture relevant kinematic and dynamic information from the foot and tibia. The design also allows the Tnor-Lx to be attached to the Hybrid III, either at the hip, or at the knee.

Experimental testing was performed to provide input data for a new, multi-body computer model of the Hybrid III lower extremity, with the 30 degree dorsiflexion ankle. The leg was disassembled into its components to mass, geometric, and inertial properties for each segment. Stiffness and damping coefficients were measured for the hip, leg, foot, and ankle. Joint rotational and translational properties were measured for the knee and ankle. To characterize interactions of the foot with the footwell, flexion and compression tests of the foot were conducted. The lower extremity was segmented at the joint and load cell locations, to permit rigid body dynamics codes to compute the forces at these locations for comparison to test data and for calculation of injury criteria.

Early influences upon Thor ATD development are described, and the path of Thor development is traced up to the release of the current Thor ALPHA ATD design. Since the display of the first Thor ATD prototype at the 15th ESV Conference in Melbourne in 1996, Thor has undergone extensive test and evaluation on an international basis in cooperation with many partner institutions. This paper summarizes some of the lessons learned from this broad test experience, and documents actions which have been undertaken to upgrade the Thor product to ALPHA status in light of this experience.

An Articulated Total Body frontal crash simulation was created with the dummy's right foot placed on the brake pedal. This study examined how interaction of the driver's foot with the brake pedal influenced the behavior of the lower extremities in frontal collisions. Braking parameters considered in the study included foot position on the pedal, whether or not the occupant's muscles were tensed and if the brake pedal was rigid or was allowed to depress. Two basic foot positions were identified as most likely to induce injury of the lower limb. One represented a foot that was pivoted about the heel from the gas pedal to the brake pedal. The other position replicated a foot that was lifted from the gas pedal to the brake pedal, resulting in an initial gap between the heel and floor. Both positions resulted in different loads and behavior of the foot, indicating that driver pre-impact position is a contributing factor to one's injury risk.

A series of eight sled tests was conducted using Hybrid III dummies and cadavers in order to examine the influence of foot placement on the brake pedal in frontal collisions. The brake pedal in the sled runs was fixed in a fully depressed position and the occupants' muscles were not tensed. The cadaver limbs and the Hybrid III lower extremities with 45° ankle and soft joint-stop were extensively instrumented to determine response during the crash event. Brake pedal reaction forces were measured using a six-axis load cell and high speed film was used for kinematic analysis of the crashes. Four right foot positions were identified from previous simulation studies as those orientations most likely to induce injury. In each test, the left foot was positioned on a simulated footrest, acting as a control variable that produced repeatable results in all dummy tests. Each of the different right foot orientations resulted in different loads and motions of the right leg and foot.

Traumatic aortic rupture is a significant cause of fatalities in frontal automobile crashes. However, such ruptures are difficult to reproduce experimentally in cadaveric surrogates, and it is difficult to observe dynamic aortic response in situ. So, the aortic injury mechanism or mechanisms remains in dispute. This study is a staged investigation of the physical parameters and mechanisms of human aortic rupture. The investigation includes both experimental study of local and global viscoelastic properties and failure properties of aortas using aortic tissue samples, excised aortas in vitro, and whole human aortas in situ in cadaver thoraxes. This study is the first phase in a staged programme to develop a finite element computer model of aorta injury to examine the mechanisms of aorta injury in automobile crashes.

The University of Virginia is investigating the use of a magnetohydrodynamic (MHD) angular rate sensor to measure head angular acceleration in impact testing. Output from the sensor, which measures angular velocity, must be differentiated to produce angular acceleration. As a precursor to their use in actual testing, a torsional pendulum was developed to analyze an MHD sensor's effectiveness in operating under impact conditions. Differentiated and digitally filtered sensor data provided a good match with the vibratory response of the pendulum for various magnitudes of angular acceleration. Subsequent head drop tests verified that MHD sensors are suitable for measuring head angular acceleration in impact testing.

Three-dimensional simulation models of a driver's right upper extremity interacting with a deploying airbag have been set up and run with the Articulated Total Body program. The goal of this study is to examine the significance of various occupant and airbag parameters during deployment, such as grip strength, upper extremity position, shoulder compliance, flap position, flap aggressivity, and deployment speed. Given a range of 250 N to 650 N, the grip strength did not affect the resultant loads. Also, the contact force and torque at the e.g. of the forearm are not sensitive to shoulder joint compliance. The flap aggressivity and the position of the airbag module relative to the upper extremity are most important in affecting the interaction. This study is used to justify cadaveric experiments involving disarticulated upper extremities.

Originally designed for measuring closed-loop contours such as those around a human thorax, the External Peripheral Instrument for Deformation Measurement (EPIDM), or chestband, was developed to improve the measurement of dummy and cadaver thoracic response during impact. In the closed-loop configuration, the chestband wraps around on itself forming a closed contour. This study investigates the use of the chestband for dynamic deformation measurements in an open-loop configuration. In the open-loop configuration, the chestband does not generally form a closed contour. This work includes enhanced procedures and algorithms for the calculation of chestband deformation contours including the determination of static and dynamic chestband contours under several boundary conditions.

Advancements in computational techniques used to simulate human impact injury response, coupled with those in computer hardware, bring the idea of detailed injury assessment closer to reality. Consequently, next-generation (G2) injury assessment processes are being explored to potentially augment or replace methods using dummy-based, empirically-derived, gross injury risk relationships. These processes use computational models that give more detailed injury response resulting from dummy-measured loading. This paper discusses the development of an initial version of such a next-generation injury assessment tool called SIMon: A Simulated Injury Monitor, as it is applied to the assessment of brain injury.

This paper presents dummy and cadaver experiments designed to investigate the injury potential of an out-of-position small female head and neck from a deploying side air bag. Three seat mounted, thoracic type, side air bags were used that varied in inflator aggressivity. The ATB/CVS multi body program was used to identify the worst case loading position for the small female head and neck. Once the initial position was identified, a total of three Hybrid III 5th percentile dummy and three small female cadaver tests (51 ± 9 years, 64 ± 8 kg, 159 ± 10 cm) were performed. Instrumentation for the dummy included upper and lower neck load cells, while both the dummy and the cadavers had accelerometers and angular rate sensors fixed to the head and T1 vertebrae in order to provide head and neck kinematic data. Head center of gravity accelerations for the dummy ranged from 71 g's to 154 g's, and were greater than cadaver values, which ranged from 68 g's to 103 g's.

This work studies the effect of padding on the force levels in impulsively loaded dummy lower extremities. Tests include the effect of padding incorporated into the soles of shoes and an examination of the potential of shoe padding for mitigating impact loading on the lower extremities. Three different shoes and three paddings were studied using a pendulum impactor; two different padding levels were studied in an impact sled test with simulated translational structural intrusion. The tests indicate a greater than 20% variation in peak axial force imparted to the lower tibia between shoes, and a greater than 50% variation in peak axial force across the paddings tested. From sled tests with simulated structural intruaion, we see a decrease of approximately 15% in peak axial load and a decrease of over 20% in peak anterior/posterior moment.

Recently there has been a greater awareness of the increased risk of certain injuries associated with air bag deployment, especially the risks to small occupants, often women. These injuries include serious eye and upper extremity injuries and even fatalities. This study investigates the interaction of a deploying air bag with cadaveric upper extremities in a typical driving posture; testing concentrates on female occupants. The goals of this investigation are to determine the risk of upper extremity injury caused by primary contact with a deploying air bag and to elucidate the mechanisms of these upper extremity injuries. Five air bags were used that are representative of a wide range of air bag ‘aggressivities’ in the current automobile fleet. This air bag ‘aggressivity’ was quantified using the response of a dummy forearm under air bag deployment.