Refine Your Search

Search Results

Viewing 1 to 19 of 19
Standard

Cast Shot and Grit Size Specifications for Peening and Cleaning

2017-10-10
CURRENT
J444_201710
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
Standard

Cut Wire Shot

2018-07-23
WIP
J441
This SAE Recommended Practice is considered to be tentative and is subject to modification to meet new developments or requirements. It is offered as a guide in the selection and use of cut wire shot.
Standard

High-Carbon Cast-Steel Grit

2013-10-16
HISTORICAL
J1993_201310
This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.
Standard

High-Carbon Cast-Steel Grit

2019-02-21
CURRENT
J1993_201902
This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.
Standard

High-Carbon Cast-Steel Shot

2019-10-31
CURRENT
J827_201910
This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.
Standard

Medical Device Shot Peening

2019-05-09
WIP
J3020
This SAE Standard and its supplementary detail specifications cover the engineering requirements for the controlled shot peening of a medical device where shot peening is required for enhancement of a material's mechanical properties through the intentional creation of compressive residual stress.
Standard

Medical Device Shot Peening

2014-05-07
CURRENT
J3020_201405
This SAE Standard and its supplementary detail specifications cover the engineering requirements for the controlled shot peening of a medical device where shot peening is required for enhancement of a material's mechanical properties through the intentional creation of compressive residual stress.
Standard

Metallic Shot and Grit Mechanical Testing

2018-07-23
WIP
J445
This SAE Information Report is intended to provide users and producers of metallic shot and grit with general information on methods of mechanically testing metal shot in the laboratory.
Standard

Metallic Shot and Grit Mechanical Testing

2013-08-21
CURRENT
J445_201308
This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.
Standard

Shot Peening Coverage Determination

2019-03-18
WIP
J2277
This SAE recommended practice provides some procedure for determining shot peening coverage and relating coverage to part exposure to the media stream. Effectiveness of shot peening is directly dependent on coverage. Either incomplete or excessive coverage can be detrimental to fatigue strength and life.
Standard

Specifications for Low Carbon Cast Steel Shot

2020-09-01
WIP
J2175
This SAE Recommended Practice describes chemical analysis, hardness, microstructure, and physical characteristic requirements for low carbon cast steel shot to be used for shot peening or blast cleaning operations.
Standard

Surface Texture Control

2011-08-04
CURRENT
J449_201108
SAE J448, Surface Texture, has been set up for precision reference specimens using a controlled surface profile to obtain reproducible roughness values. These specimens are for instrument calibration. Appropriate symbols for roughness, waviness, and lay have also been standardized (ASA B46.1-1962 and SAE J448). For production control, especially from one geographical location to another, means are required to facilitate the inspection of surface characteristics called for by specifications which include not only roughness but profile waviness and lay. In order to integrate the requirements of the designer with the actual production of surfaces, a second grade of control standards must be adopted which will be functional in nature for the specific product being manufactured. These control standards may be Calibrated Pilot Specimens (actual parts with satisfactory texture) or Roughness Comparison Specimens (ASA B46.1-1962).
X