Standard
CAST STEEL GRIT
1993-03-01
HISTORICAL
J1993_199303
This SAE Recommended Practice describes the chemical composition and the physical requirements for high carbon cast steel grit.
Search Results
Standard
CAST STEEL SHOT
1990-03-01
HISTORICAL
J827_199003
This SAE Recommended Practice describes chemical analysis, hardness, microstructure and physical characteristic requirements for cast steel shot to be used for shot peening or blast cleaning operations.
Standard
CAST STEEL SHOT
1962-06-01
HISTORICAL
J827_196206
Standard
CAST STEEL SHOT
1969-01-01
HISTORICAL
J827_196901
Standard
Cast Shot and Grit Size Specifications for Cleaning and Peening
2023-06-27
CURRENT
J444_202306
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
Standard
Computer Generated Shot Peening Saturation Curves
2010-01-14
HISTORICAL
J2597_201001
This SAE Recommended Practice defines a procedure for the use of computer generated saturation curves to determine peening intensity. Calculation of intensity within a tolerance band for each data set in Table 1 one is required for compliance with this practice.
Standard
Computer Generated Shot Peening Saturation Curves
2022-05-16
WIP
J2597
This SAE Recommended Practice defines a procedure for the use of computer generated saturation curves to determine peening intensity. Calculation of intensity within a tolerance band for each data set in Table 1 one is required for compliance with this practice.
Standard
DEFINITIONS FOR MACROSTRAIN AND MICROSTRAIN
1985-08-01
HISTORICAL
J932_198508
In the analysis and measurement of residual stresses of materials, it has been noted that there are frequently differences in interpretation of the terms "macrostrain" and "microstrain." To assist communication among research personnel in this area, definitions for these two terms are suggested by the Fatigue Design and Evaluation Committee of SAE. Since "macrostress" is commonly computed from "macrostrain" in residual stress analysis, to be consistent, the definitions given are for "macrostrain" and "microstrain."
Standard
Definition for Particle Size
2011-06-01
CURRENT
J391_201106
"Effective particle or domain size" is a phrase used in X-ray diffraction literature to describe the size of the coherent regions within a material which are diffracting. Coherency in this sense means diffracting as a unit. Small particle size causes X-ray line broadening and as such can be measured. It has been shown related to substructure as observed in transmission electron microscopy. Particle size is affected by hardening, cold working, and fatigue; conversely, there is increasing evidence that particle size, per se, affects both static and dynamic strength.
Standard
Definitions for Macrostrain and Microstrain
2011-08-04
CURRENT
J932_201108
In the analysis and measurement of residual stresses of materials, it has been noted that there are frequently differences in interpretation of the terms "macrostrain" and "microstrain." To assist communication among research personnel in this area, definitions for these two terms are suggested by the Fatigue Design and Evaluation Committee of SAE. Since "macrostress" is commonly computed from "macrostrain" in residual stress analysis, to be consistent, the definitions given are for "macrostrain" and "microstrain."
Standard
HIGH-CARBON CAST-STEEL GRIT
1996-09-01
HISTORICAL
J1993_199609
This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.
Standard
HIGH-CARBON CAST-STEEL SHOT
1996-09-01
HISTORICAL
J827_199609
This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.
Standard
High-Carbon Cast-Steel Grit
2019-02-21
CURRENT
J1993_201902
This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.
Standard
High-Carbon Cast-Steel Grit
2005-07-25
HISTORICAL
J1993_200507
This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.
Standard
High-Carbon Cast-Steel Grit
2013-10-16
HISTORICAL
J1993_201310
This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.
Standard
High-Carbon Cast-Steel Shot
2005-07-25
HISTORICAL
J827_200507
This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.
Standard
High-Carbon Cast-Steel Shot
2019-10-31
CURRENT
J827_201910
This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.
Standard
METALLIC SHOT AND GRIT MECHANICAL TESTING
1996-04-01
HISTORICAL
J445_199604
This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.
Standard
METALLIC SHOT AND GRIT MECHANICAL TESTING
1984-08-01
HISTORICAL
J445_198408
This report is intended to provide users and producers of metallic shot and grit1 with general information on methods of mechanically testing metal shot in the laboratory.
Standard
Manual on Shot Peening
1992-10-01
CURRENT
J808_199210
Not available.
