Refine Your Search

Topic

Search Results

Standard

Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Air-Cooled Xenon-Arc Apparatus

2012-11-19
CURRENT
J2019_201211
This SAE Standard specifies the operating procedures for a controlled irradiance, air-cooled xenon-arc apparatus used for the accelerated exposure of various automotive exterior materials. The sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
Standard

Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Water-Cooled Xenon Arc Apparatus

2008-01-11
CURRENT
J1960_200801
This test method specifies the operating procedures for a controlled irradiance, water-cooled xenon arc apparatus used for the accelerated exposure of various automotive exterior materials. This standard is limited to the models of xenon arc test apparatus specified in the Section on Apparatus. All other models of xenon arc test apparatus must use SAE J2527 to perform the test conditions specified in SAE J1960. SAE J2527 is the performance standard based on the test parameters of SAE J1960. Use of xenon arc test apparatus to perform SAE J2527 must be agreed upon by contractual parties.
Standard

Accelerated Exposure of Automotive Exterior Materials Using a Fluorescent Uv and Condensation Apparatus

1995-05-01
HISTORICAL
J2020_199505
This test method specifies the operating conditions for a fluorescent ultraviolet (UV) and the condensation apparatus used for the accelerated exposure of various automotive exterior components. The sample preparation, test, duration, and performance evaluation procedures are addressed by each automotive manufacturer's material specifications. This SAE Standard may involve hazardous materials, operations, and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of whoever uses this document to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. This test method is designed to simulate extreme environmental conditions encountered on the outside of an automobile due to sunlight, heat, and humidity and to provide an acceleration of exposure for the purpose of predicting the performance of exterior automotive materials.
Standard

Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Water Cooled Xenon-Arc Apparatus

2008-01-11
CURRENT
J1885_200801
This test method specifies the operating procedures for a controlled irradiance, water cooled xenon-arc apparatus used for the accelerated exposure of various automotive interior trim components. Test durations, as well as any exceptions to the sample preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers. This standard is limited to the models of xenon arc test apparatus specified in the Section on Equipment. All other models of xenon arc test apparatus must use SAE J2412 to perform the test conditions specified in SAE J1885. SAE J2412 is the performance standard based on the test parameters of SAE J1885. Use of xenon arc test apparatus to perform SAE J2412 must be agreed upon by contractual parties.
Standard

Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Xenon-Arc Apparatus

2015-12-14
WIP
J2412
This test method specifies the operating procedures for a controlled irradiance, xenon arc apparatus used for the accelerated exposure of various automotive interior trim components. Test duration as well as any exceptions to the specimen preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers. Any deviation to this test method, such as filter combinations, is to be agreed upon by contractual parties.
Standard

Accelerated Exposure of Automotive Interior Trim Material Using Outdoor Under-Glass Controlled Sun-Tracking Temperature and Humidity Apparatus

2016-03-23
WIP
J2230
This SAE Standard specifies operating procedure for the exposure of automotive interior trim materials in an outdoor behind-glass apparatus in which the temperature is controlled in a 24 h cycle. The humidity is controlled during the dark (night) portion of the cycle. Specimen preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
Standard

Design Guidelines for Fiberboard Materials

2010-06-21
HISTORICAL
J1774_201006
This document provides information on the various fiberboard products, which are available for automotive application. It is intended to give engineers and designers a better understanding of product usage, characteristics, properties and industry terminology. The following sections cover these topics: 2 General Product Information 3 Design Characteristics 4 Physical/Mechanical Properties 5 Fiberboard Definitions In sections 2, 3 and 4 the fiberboard products are categorized. These sections give an overview of product types, with general information about characteristics and properties. In cases where product categories encompass more than one material or material grade, ranges were established to cover all of the products in that category. The individual companies that supply fiberboard products should be consulted for specific information about a particular product or application.
Standard

Design Guidelines for Fiberboard Materials

2019-09-25
CURRENT
J1774_201909
This document provides information on the various fiberboard products, which are available for automotive application. It is intended to give engineers and designers a better understanding of product usage, characteristics, properties and industry terminology. The following sections cover these topics: 2 General Product Information 3 Design Characteristics 4 Physical/Mechanical Properties 5 Fiberboard Definitions In sections 2, 3 and 4 the fiberboard products are categorized. These sections give an overview of product types, with general information about characteristics and properties. In cases where product categories encompass more than one material or material grade, ranges were established to cover all of the products in that category. The individual companies that supply fiberboard products should be consulted for specific information about a particular product or application.
Standard

Felts - Wool and Part Wool

2012-08-24
CURRENT
J314_201208
This SAE Standard identifies chemical/mechanical properties, thickness, width, mass, and other requirements recommended for felts (refer to Tables 1 and 2). It was developed with the cooperation of the Standardization Committee of the Felt Association, Inc., and in accordance with the ASTM tests indicated in the document. The commercial trade designations of the more commonly used grades of automotive felts are given along with complete specifications and tolerances for thickness, mass, wool content, chemical and physical requirements, color, and width. General information, recommended uses, etc., are published in Appendix A as a guide in the selection of felts for particular uses, but the requirements for each application should be taken into consideration in making final selections.
Standard

Fiberboard Crease Bending Test

1982-01-01
HISTORICAL
J119_198201
This test method is designed to determine the suitability of a painted or unpainted fiberboard for application involving creasing and bending. The specific purpose of the test is to determine whether a given material, properly creased, can be bent along the impressed crease without objectionable failure on the surface of the bend.
Standard

Fiberboard Crease Bending Test

2019-10-31
CURRENT
J119_201910
This test method is designed to determine the suitability of a painted or unpainted fiberboard for application involving creasing and bending. The specific purpose of the test is to determine whether a given material, properly creased, can be bent along the impressed crease without objectionable failure on the surface of the bend.
Standard

Fiberboard Crease Bending Test

2010-05-10
HISTORICAL
J119_201005
This test method is designed to determine the suitability of a painted or unpainted fiberboard for application involving creasing and bending. The specific purpose of the test is to determine whether a given material, properly creased, can be bent along the impressed crease without objectionable failure on the surface of the bend.
X