Refine Your Search

Search Results

Standard

Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Water-Cooled Xenon Arc Apparatus

2008-01-11
CURRENT
J1960_200801
This test method specifies the operating procedures for a controlled irradiance, water-cooled xenon arc apparatus used for the accelerated exposure of various automotive exterior materials. This standard is limited to the models of xenon arc test apparatus specified in the Section on Apparatus. All other models of xenon arc test apparatus must use SAE J2527 to perform the test conditions specified in SAE J1960. SAE J2527 is the performance standard based on the test parameters of SAE J1960. Use of xenon arc test apparatus to perform SAE J2527 must be agreed upon by contractual parties.
Standard

Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Water Cooled Xenon-Arc Apparatus

2005-03-09
HISTORICAL
J1885_200503
This test method specifies the operating procedures for a controlled irradiance, water cooled xenon arc apparatus used for the accelerated exposure of various automotive interior trim components. Test durations, as well as any exceptions to the sample preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers.
Standard

Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Water Cooled Xenon-Arc Apparatus

2008-01-11
CURRENT
J1885_200801
This test method specifies the operating procedures for a controlled irradiance, water cooled xenon-arc apparatus used for the accelerated exposure of various automotive interior trim components. Test durations, as well as any exceptions to the sample preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers. This standard is limited to the models of xenon arc test apparatus specified in the Section on Equipment. All other models of xenon arc test apparatus must use SAE J2412 to perform the test conditions specified in SAE J1885. SAE J2412 is the performance standard based on the test parameters of SAE J1885. Use of xenon arc test apparatus to perform SAE J2412 must be agreed upon by contractual parties.
Standard

Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Water Cooled Xenon-Arc Apparatus

1992-03-01
HISTORICAL
J1885_199203
This test method specifies the operating procedures for a controlled irradiance, water cooled xenon arc apparatus used for the accelerated exposure of various automotive interior trim components. Test durations, as well as any exceptions to the sample preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers.
Standard

Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Water Cooled Xenon-Arc Apparatus

1987-08-01
HISTORICAL
J1885_198708
This test method specifies the operating procedures for a controlled irradiance, water cooled xenon arc apparatus used for the accelerated exposure of various automotive interior trim components. Test durations, as well as any exceptions to the sample preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers.
Standard

Felts - Wool and Part Wool

2012-08-24
CURRENT
J314_201208
This SAE Standard identifies chemical/mechanical properties, thickness, width, mass, and other requirements recommended for felts (refer to Tables 1 and 2). It was developed with the cooperation of the Standardization Committee of the Felt Association, Inc., and in accordance with the ASTM tests indicated in the document. The commercial trade designations of the more commonly used grades of automotive felts are given along with complete specifications and tolerances for thickness, mass, wool content, chemical and physical requirements, color, and width. General information, recommended uses, etc., are published in Appendix A as a guide in the selection of felts for particular uses, but the requirements for each application should be taken into consideration in making final selections.
Standard

Fiberboard Crease Bending Test

2010-05-10
HISTORICAL
J119_201005
This test method is designed to determine the suitability of a painted or unpainted fiberboard for application involving creasing and bending. The specific purpose of the test is to determine whether a given material, properly creased, can be bent along the impressed crease without objectionable failure on the surface of the bend.
Standard

Instrumental Color Difference Measurements for Colorfastness of Automotive Interior Trim Materials

2019-06-05
WIP
J1767
The practice described applies to textile and flexible plastic parts and materials used in automotive vehicles. Special care should be taken when high pile carpet samples are being evaluated. The intent of this SAE Recommended Practice is to specify procedures for the instrumental measurement of color differences brought about by the exposure of textile and flexible plastic automotive parts to various colorfastness tests. It may be used for the specification of limits of color differences which may be tolerated in a specific test.
Standard

Standard Classification System for Fiberboards

2014-06-04
CURRENT
J1323_201406
This SAE Standard provides a means for specifying or describing the pertinent properties of fiberboards for automotive applications. The materials normally specified by this standard are defined in SAE J947. The test methods commonly used for fiberboards are defined in SAE J315.
Standard

Test Method for Determining Blocking Resistance and Associated Characteristics of Automotive Trim Materials

2012-10-15
CURRENT
J912_201210
This test method is designed to indicate the degree of surface tackiness, color transfer, loss of embossment, and surface marring when two trim materials are placed face to face under specific conditions of time, temperature, and pressure. These specific conditions are not dictated in this test procedure but will be found in the material standards which govern each type of trim material to be tested.
X