Refine Your Search

Search Results

Standard

Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Air-Cooled Xenon-Arc Apparatus

2012-11-19
CURRENT
J2019_201211
This SAE Standard specifies the operating procedures for a controlled irradiance, air-cooled xenon-arc apparatus used for the accelerated exposure of various automotive exterior materials. The sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
Standard

Accelerated Exposure of Automotive Exterior Materials Using a Fluorescent Uv and Condensation Apparatus

1995-05-01
HISTORICAL
J2020_199505
This test method specifies the operating conditions for a fluorescent ultraviolet (UV) and the condensation apparatus used for the accelerated exposure of various automotive exterior components. The sample preparation, test, duration, and performance evaluation procedures are addressed by each automotive manufacturer's material specifications. This SAE Standard may involve hazardous materials, operations, and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of whoever uses this document to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. This test method is designed to simulate extreme environmental conditions encountered on the outside of an automobile due to sunlight, heat, and humidity and to provide an acceleration of exposure for the purpose of predicting the performance of exterior automotive materials.
Standard

Fiberboard Crease Bending Test

2010-05-10
HISTORICAL
J119_201005
This test method is designed to determine the suitability of a painted or unpainted fiberboard for application involving creasing and bending. The specific purpose of the test is to determine whether a given material, properly creased, can be bent along the impressed crease without objectionable failure on the surface of the bend.
Standard

Instrumental Color Difference Measurement for Exterior Finishes, Textiles and Colored Trim

2019-06-05
WIP
J1545
The practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials that are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film.
Standard

Instrumental Color Difference Measurement for Exterior Finishes, Textiles and Colored Trim

2005-07-25
HISTORICAL
J1545_200507
The practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials that are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film.
Standard

Instrumental Color Difference Measurement for Exterior Finishes, Textiles and Colored Trim

2014-10-27
CURRENT
J1545_201410
The practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials that are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film.
Standard

Instrumental Color Difference Measurement for Exterior Finishes, Textiles, and Colored Trim

1986-06-01
HISTORICAL
J1545_198606
The intent of this practice is to precisely specify procedures for instrumental color difference measurement of colored parts or colored materials incorporated in the manufacture of vehicles. The recommended practice provides a consistent engineering practice for determination of color difference, for numerical communication of color difference, and for determination of acceptance or rejection compared to numerical tolerances. The practice is intended to be used as a specification and means of communication for color part acceptance in a buyer-seller agreement. The practice applies to parts and materials used in vehicles manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials which are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, and exterior hard trim, and exterior film.
Standard

Instrumental Color Difference Measurements for Colorfastness of Automotive Interior Trim Materials

2019-06-05
WIP
J1767
The practice described applies to textile and flexible plastic parts and materials used in automotive vehicles. Special care should be taken when high pile carpet samples are being evaluated. The intent of this SAE Recommended Practice is to specify procedures for the instrumental measurement of color differences brought about by the exposure of textile and flexible plastic automotive parts to various colorfastness tests. It may be used for the specification of limits of color differences which may be tolerated in a specific test.
Standard

Method of Testing Resistance to Crocking of Organic Trim Materials

2012-08-24
CURRENT
J861_201208
This test can be used to determine the resistance to crocking (color rub-off) of organic trim materials such as fabrics, vinyl coated fabrics, leather, coated fiberboard and carpet. This method is similar to AATCC Method 8 –Colorfastness to Crocking.
Standard

Outdoor Weathering of Exterior Materials

2012-04-16
CURRENT
J1976_201204
This test method specifies the exposure racks, black boxes, and instrumentation, which shall be used for the outdoor weathering of materials for automotive exterior application.
Standard

Procedure for Visual Evaluation of Interior and Exterior Automotive Trim

2016-11-18
HISTORICAL
J361_201611
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
Standard

Procedure for Visual Evaluation of Interior and Exterior Automotive Trim

2017-04-17
CURRENT
J361_201704
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100 Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
Standard

Procedure for Visual Evaluation of Interior and Exterior Automotive Trim

2013-08-14
HISTORICAL
J361_201308
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim.
Standard

Standard Classification System for Fiberboards

2014-06-04
CURRENT
J1323_201406
This SAE Standard provides a means for specifying or describing the pertinent properties of fiberboards for automotive applications. The materials normally specified by this standard are defined in SAE J947. The test methods commonly used for fiberboards are defined in SAE J315.
Standard

Test Method for Determining Blocking Resistance and Associated Characteristics of Automotive Trim Materials

2012-10-15
CURRENT
J912_201210
This test method is designed to indicate the degree of surface tackiness, color transfer, loss of embossment, and surface marring when two trim materials are placed face to face under specific conditions of time, temperature, and pressure. These specific conditions are not dictated in this test procedure but will be found in the material standards which govern each type of trim material to be tested.
X