Search Results

Abstract One of the most important factors affecting the performance of vehicle active chassis control systems is the tire-road friction coefficient. Accurate estimation of the friction coefficient can lead to better performance of these controllers. In this study, a new three-step friction estimation algorithm, based on intelligent tire concept, is proposed, which is a combination of experiment-based and vehicle dynamic based approaches. In the first step of the proposed algorithm, the normal load is estimated using a trained Artificial Neural Network (ANN). The network was trained using the experimental data collected using a portable tire testing trailer. In the second step of the algorithm, the tire forces and the wheel longitudinal velocity are estimated through a two-step Kalman filter. Then, in the last step, using the estimated tire normal load and longitudinal and lateral forces, the friction coefficient can be estimated.

Abstract Vehicle-to-infrastructure (V2I) connectivity technology presents the opportunity for vehicles to perform autonomous longitudinal control to navigate safely and efficiently through sequences of V2I-enabled intersections, known as connected corridors. Existing research has proposed several control systems to navigate these corridors while minimizing energy consumption and travel time. This article analyzes and compares the simulated performance of three different autonomous navigation systems in connected corridors: a V2I-informed constant acceleration kinematic controller (V2I-K), a V2I-informed model predictive controller (V2I-MPC), and a V2I-informed reinforcement learning (V2I-RL) agent. A rules-based controller that does not use V2I information is implemented to simulate a human driver and is used as a baseline. The performance metrics analyzed are net energy consumption, travel time, and root-mean-square (RMS) acceleration.

Abstract A Direct Yaw-Moment Control (DYC) logic for a rear-wheel-drive electric-powered vehicle is proposed. The vehicle is a Formula SAE (FSAE) type race car, with two electric motors powering each rear wheel. Vehicle baseline balance is neutral at low speeds, for increased maneuverability, and increases understeering at high speeds (due to the aerodynamic configuration) for stability. A controller that can deal with these yaw response variations, modelling uncertainties, and vehicle nonlinear behavior at limit handling is proposed. A two-level control strategy is considered. For the upper level, yaw rate and sideslip angle are considered as feedback control variables and a cubic-error Proportional Derivative (PD) controller is proposed for the feedback control. For the lower level, a traction control algorithm is used, together with the yaw moment requirement, for torque allocation.

Abstract The cold crank-start stage, including the first three engine cycles, is responsible for a significant amount of the cold-start phase emissions in a Gasoline Direct Injection (GDI) engine. The engine crank-start is highly transient due to substantial engine speed changes, Manifold Absolute Pressure (MAP) dynamics, and in-cylinder temperatures. Combustion characteristics change depending on control inputs variations, including throttle angle and spark timing. Fuel injection strategy, timing, and vaporization dynamics are other parameters causing cold-start first cycles analysis to be more complex. Hybrid Electric Vehicles (HEVs) provide elevated cranking speed, enabling technologies such as cam phasing to adjust the valve timing and throttling, and increased fuel injection pressure from the first firings.

Abstract Modern Automated Driving (AD) systems rely on safety measures to handle faults and to bring the vehicle to a safe state. To eradicate lethal road accidents, car manufacturers are constantly introducing new perception as well as control systems. Contemporary automotive design and safety engineering best practices are suitable for analyzing system components in isolation, whereas today’s highly complex and interdependent AD systems require a novel approach to ensure resilience to multiple-point failures. We present a holistic and cost-effective safety concept unifying advanced safety measures for handling multiple-point faults. Our proposed approach enables designers to focus on more pressing issues such as handling fault-free hazardous behavior associated with system performance limitations. To verify our approach, we developed an executable model of the safety concept in the formal specification language mCRL2.

Abstract Autonomous vehicles (AVs) are expected to have a great impact on mobility by decreasing commute time and vehicle fuel consumption and increasing safety significantly. However, there are still issues that can jeopardize their wide impact and their acceptance by the public. One of the main limitations is motion sickness (MS). Hence, the last year’s research is focusing on improving motion comfort within AVs. On one hand, users are expected to perceive AVs driving style as more aggressive, as it might result in excessive head and body motion. Therefore, speed reduction should be considered as a countermeasure of MS mitigation. On the other hand, the excessive reduction of speed can have a negative impact on traffic. At the same time, the user’s dissatisfaction, i.e., acceptance and subjective comfort, will increase due to a longer journey time.

Abstract Quantifying exhaust gas composition and temperature in vehicles with internal combustion engines (ICEs) is crucial to understanding and reducing emissions during transient engine operation. This is particularly important before the catalytic converter system lights off (i.e., during cold start). Most commercially available gas analyzers and temperature sensors are far too slow to measure these quantities on the timescale of individual cylinder-firing events, thus faster sensors are needed. A two-color mid-infrared (MIR) laser absorption spectroscopy (LAS) sensor for gas temperature and carbon monoxide (CO) mole fraction was developed and applied to address this technology gap. Two quantum cascade lasers (QCLs) were fiber coupled into one single-mode fiber to facilitate optical access in the test vehicle exhaust. The QCLs were time-multiplexed in order to scan across two CO absorption transitions near 2013 and 2060 cm–1 at 15 kHz.

Abstract The tailpipe zero-emission legislation has pushed the automotive industry toward more electrification. Regenerative braking is the capability of electric machines to provide brake torque. So far, the regenerative braking feature is primarily considered due to its effect on energy efficiency. However, using individual e-machines for each wheel makes it possible to apply the antilock braking function due to the fast torque-tracking characteristics of permanent magnet synchronous motors (PMSM). Due to its considerable cost reduction, in this article, a feasibility study is carried out to investigate if the ABS function can be done purely through regenerative braking using a mid-fidelity model-based approach. An uni-tire model of the vehicle with a surface-mount PMSM (SPMSM) model is used to verify the idea. The proposed ABS control system has a hierarchical structure containing a high-level longitudinal slip controller and a low-level SPMSM torque controller.

Abstract The two-wheel system design is widely used in various mobile tools, such as remote-control vehicles and robots, due to its simplicity and stability. However, the specific wheel and body models in the real world can be complex, and the control accuracy of existing algorithms may not meet practical requirements. To address this issue, we propose a double inverted pendulum on mobile device (DIPM) model to improve control performances and reduce calculations. The model is based on the kinetic and potential energy of the DIPM system, known as the Euler-Lagrange equation, and is composed of three second-order nonlinear differential equations derived by specifying Lagrange. We also propose a stable feedback control method for mobile device drive systems. Our experiments compare several mainstream reinforcement learning (RL) methods, including linear quadratic regulator (LQR) and iterative linear quadratic regulator (ILQR), as well as Q-learning, SARSA, DQN (Deep Q Network), and AC.

Abstract The principal issue in choosing an energy management strategy (EMS) for hybrid electric vehicles (HEVs) has been the way of determining the optimal share of electric energy in hybrid drive. In this article, a novel EMS is proposed that, along with maximum engine efficiency in the hybrid drive, can optimize the share of battery energy for the maximum efficiency of vehicle power train expanded with an imaginary power plant that, by delivering the electric energy to a grid, feeds the vehicle battery. It is proved that the expanded power train efficiency has the local maximum for a wide range of wheel power demand. The relation between the wheel power demand in hybrid drive, the share of battery energy, and the maximum efficiency of the expanded power train is conducted offline. Downloaded to the onboard control system, it enables the operation with the instantaneously optimal share of battery energy and the control system to operate with the low computational load.

Abstract Nowadays, with the great advancement of automobile intellectualization, vehicle integrated dynamic control is increasingly becoming a hot research field. For vehicle stability, this article focuses on the coordinated control of Direct Yaw-moment Control (DYC) and Active Front Steering (AFS). First of all, the nominal control variables (yaw rate and sideslip angle) are designed based on the linear two Degrees of Freedom (2 DOF) vehicle model, in which the phase difference between the actual and nominal variables has been pointed out due to the approximate substitution with first-order time-delay transfer function. Secondly, considering the uncertainty of cornering stiffness per axle, and increasing robustness of the system, the Optimal Guaranteed Cost Control (OGCC) theory is adopted to design the coordinated controller.

Abstract In this article, a novel hybrid metaheuristic based on passing vehicle search (PVS) cultural algorithm (CA) is proposed. This contribution has a twofold aim: First is to present the new hybrid PVS-CA. Second is to prove the effectiveness of the proposed algorithm for adaptive signal timing optimization. For this, a system that can adapt efficiently to the real-time traffic situation based on priority signal control is developed. Hence, Transit Signal Priority (TSP) techniques have been used to adjust signal phasing in order to serve emergency vehicles (EVs) and manage the tram priority in a coordinated tram intersection. The system used in this study provides cyclic signal operation based on a real-time control approach, including an optimization process and a database to manage the sensor data from detectors for real-time predictions of EV and tram arrival time.

Abstract The automotive industry is facing a multifaceted problem of supervisory energy management, computational power, and digitalization. In response, this article proposes the use of agents utilizing the belief, desire, and intent (BDI) framework as a means to flexibly create online vehicle management systems (VMSs). Under such proposal, a community of agents form a vehicle configuration. Each agent represents a vehicle subsystem and contains knowledge specific to its respective hardware. With this knowledge and partial observation over its operating environment, each agent uses the BDI framework to deliberate over its actions. An interaction protocol, which implements a distributed constraint satisfaction problem (DCSP) algorithm, is used between the agents to create sensible emergent behavior of the vehicle. This interaction protocol allows independently reasoning components to produce emergent behavior that is flexible, robust, verifiable, and explainable.

Abstract In order to improve the safety and dynamic performance of electric vehicles equipped with four in-wheel electric motors, and prevent the wheels from locking or slipping when braking or accelerating, a new longitudinal control strategy which combines ASR traction and ABS braking control is proposed using an observation algorithm of effective radius for four wheel of electric vehicle. Using the electric motor torques as the unique actuator signal sources, this combined ASR/ABS can act as acceleration slip regulation (ASR) by preventing the wheels from slipping during acceleration and as an antilock braking system (ABS) by preventing the wheels from getting locked during braking. A variation of effective radius of the wheel’s tire can have an incidence on the longitudinal and lateral control.

Abstract This article presents a two-stage Dynamic Programming (DP)-based approach to solving the problem of Hybrid Energy Storage System (HESS) component sizing, specifically, the lithium-ion (Li-ion) battery and ultracapacitor (UC) for a mild hybrid electric powertrain. In the first stage, optimal sizing of the battery for the powertrain without a UC is solved for a specified drive cycle, which is used in the reported literature. In the second stage, the battery is complemented with a UC cascaded through a direct current-to-direct current (DC/DC) converter in a semi-active configuration. A DP-based formulation is then constructed and solved for the hybrid energy storage subsystem.

Abstract Aiming to improve the lateral instability of adaptive cruise control (ACC) systems, both the front and rear vehicles are considered the centers of two control strategies. A vehicle control system is designed to enable the vehicle to automatically find the best following distance based on the displacement and speeds of the front and rear vehicles, hence enhancing driver assistance, traffic efficiency, and road utilization ratio. A practical model predictive control is designed to improve performance, responsiveness, and minor discomfort. A quadratic programming (QP) solver is used to construct an error preview-based mathematical model for the vehicle control, which is then applied to improve the control performance of the system to achieve relative intervehicle distance control. The time sampling of the parameters and the prediction horizon are obtained by numerical simulation, verifying the effectiveness of the ACC system proposed.

Abstract In this article, we use MPC algorithm to design an adaptive path tracking controller based on the vehicle coordinate system, which is effectively applicable to path tracking scenarios with different vehicle speeds and large path curvatures. To reduce the lateral position error and heading angle error, a fitting function learned through a large number of simulations is used to adaptively adjust the prediction horizon parameter and a compensation strategy of steering angle increment designed based on fuzzy control algorithm is used to reduce the influence of model mismatch and low modeling accuracy on the path tracking control effect, then the front wheel steering angle is calculated and output to the vehicle model for path tracking. In this article, multi-scenario simulations are conducted in Simulink and CarSim environments to verify the performance of the proposed controller.

Abstract Commercial vehicles contribute to the majority of freight transportation in the United States. They are also significant fuel consumers, with over 23% of fuel used in transportation in the United States. The gas price volatility and increasingly stringent regulation on greenhouse-gas emissions have driven manufacturers to adopt new fuel-efficient technologies. Among others, an advanced transmission control strategy, which can provide tangible improvement with low incremental cost. In the commercial sector, individual drivers have little or no interest in vehicle fuel economy, contrary to fleet owners. Aggressive driving behavior can greatly increase the real-world vehicle fuel consumption. However, the effectiveness of transmission calibration to match the shift strategy to the driving characteristics is still a challenge.

Abstract The advancement in vision sensors and embedded technology created the opportunity in autonomous vehicles to look ahead in the future to avoid potential obstacles and steep regions to reach the target location as soon as possible and yet maintain vehicle safety from rollover. The present work focuses on developing a nonlinear model predictive controller (NMPC) for a high-speed off-road autonomous vehicle, which avoids undesirable conditions including stationary obstacles, moving obstacles, and steep regions while maintaining the vehicle safety from rollover. The NMPC controller is developed using CasADi tools in the MATLAB environment. The CasADi tool provides a platform to formulate the NMPC problem using symbolic expressions, which is an easy and efficient way of solving the optimization problem. In the present work, the vehicle lateral dynamics are modeled using the Pacejka nonlinear tire model.

Abstract This article investigates the headway and optimal velocity tracking of autonomous vehicles (AVs), considering their predictive driving for the stability and integrity of spatial vehicle formation in the platoon. First, the human-like anticipation car-following model is used for modeling the autonomous system. Second, an adaptive radial basis function neural network (ARBF-NN)-based sliding mode control (SMC) is proposed for the control purpose. The control objective is to regulate traffic perturbation during entire road operations. To enable the controller to experience less computational burden and adaptation complexity, a minimum parameter learning (MPL) has also been integrated with ARBF-NN-based SMC. Third, an illustrative simulation example has been performed for two scenarios, i.e., constant headway and time-varying headway of vehicles.