Search Results

Abstract In recent years, lean-burn gasoline Spark-Ignition (SI) engines have been a major subject of investigations. With this solution, in fact, it is possible to simultaneously reduce NOx raw emissions and fuel consumption due to decreased heat losses, higher thermodynamic efficiency, and enhanced knock resistance. However, the real applicability of this technique is strongly limited by the increase in cyclic variation and the occurrence of misfire, which are typical for the combustion of homogeneous lean air/fuel mixtures. The employment of a Pre-Chamber (PC), in which the combustion begins before proceeding in the main combustion chamber, has already shown the capability of significantly extending the lean-burn limit. In this work, the potential of an ultralean PC SI engine for a decisive improvement of the thermal efficiency is presented by means of numerical and experimental analyses.

Abstract This article presents an investigation of energy transfer, flame propagation, and emissions formation mechanisms in a four-cylinder, downsized and boosted, spark ignition engine fuelled by either directly injected compressed natural gas (DI CNG) or gasoline (GDI). Three different charge preparation strategies are examined for both fuels: stoichiometric engine operation without external dilution, stoichiometric operation with external exhaust gas recirculation (EGR), and lean burn. In this work, experiments and engine modelling are first used to analyze the energy transfer throughout the engine system. This analysis shows that an early start of fuel injection (SOI) improves fuel efficiency through lower unburned fuel energy at low loads with stoichiometric DI CNG operation.

Abstract The article compares the accuracy of different exhaust gas recirculation (EGR) correction factor models under engine conditions. The effect of EGR on the laminar burning velocity of a EURO VI E10 specification gasoline (10% Ethanol content by volume) has been back calculated from engine pressure trace data, using the Leeds University Spark Ignition Engine Data Analysis (LUSIEDA) reverse thermodynamic code. The engine pressure data ranges from 5% to 25% EGR (by mass) with the running conditions, such as spark advance and pressure at intake valve closure, changed to maintain a constant engine load of 0.79 MPa gross mean effective pressure (GMEP). Based on the experimental data, a correlation is suggested on how the laminar burning velocity reduces with increasing EGR mass fraction.

Abstract This work presents a generalized methodology for the optimal thermal management of different powertrain devices. The methodology is based on the adoption of an electrically driven pump and on the development of a specifically designed controller algorithm. This is achieved following a Model Predictive Control approach and requires a generalized lumped-parameters model of the thermal exchange between the device walls and the coolant. The methodology is validated at a test rig, with reference to a four-cylinder spark-ignition engine. Results show that the proposed approach allows a reduction in fuel consumption of about 2-3% during the engine warm-up, a decrease in fuel consumption of about 1-2% during fully warmed operation, and an estimated fuel consumption reduction of about 2.5-3% in an NEDC. Finally, the investigation highlights that the proposed approach reduces the risk of after-boiling when the engine is rapidly switched off after a prolonged high-load operation.

Abstract The hydrocarbons constituting the heavy tail of gasoline are key contributors to particulate matter (PM) emissions from spark-ignition (SI) engines. They are predominantly aromatic and, to a significant degree, bicyclic aromatic. For example, above a boiling point of 400°F, the content of bicyclic compounds in the United States (US) summer E10 regular-grade gasoline exceeds 50%v. Various gasoline parameters, such as the PM Index, Particulate Evaluation Index (PEI), Particulate and Soot Correlation Equation (PASCE), or Threshold Sooting Index (TSI), have been proposed as predictors of PM emissions from SI engines. In particular, the PM Index, whose value is dominated by the content of heavy aromatics and which, so far, has yielded the most predictive PM emissions models, appears to be the best metric to achieve this objective.

Abstract Three-dimensional patterns representing crosshatched plateau-honed cylinder bores based on two-dimensional Fast Fourier Transform (FFT) of measured surfaces were generated and used to calculate pressure flow, shear-driven flow, and shear stress factors. Later, the flow and shear stress factors obtained by numerical simulations for various surface patterns were used to calculate lubricant film thickness and friction force between piston ring and cylinder bore contact in typical diesel engine conditions using a mixed lubrication model. The effects of various crosshatch honing angles, such as 30°, 45°, and 60°, and texture heights on engine friction losses, wear, and oil consumption were discussed in detail. It is observed from numerical results that lower lubricant film thickness values are generated with higher honing angles, particularly in mixed lubrication regime where lubricant film thickness is close to the roughness level, mainly due to lower resistance to pressure flow.

Abstract Realizing the potential of the gasoline direct injection (GDI) concept lies in effectively stratifying the charge at different engine operating conditions. This is generally obtained by properly directing the air and fuel through carefully oriented intake port(s) and fuel spray and appropriately changing injection parameters. However, robust methods of charge stratification are essential to extend the lean operating range, particularly in small GDI engines. In this work, a novel piston shape was developed for a 200 cm3, single-cylinder, four-stroke gasoline engine to attain charge stratification. Stratification of charge is achieved even when the fuel was injected early in the intake stroke by a specially shaped wedge on the piston crown that produced twin vortices during compression and physically separated the charge into two sides in the combustion chamber.

Abstract This work focuses on the effects of the laminar flame speed (LFS) and flame stretch on the phenomenological modeling of the combustion process in spark ignition engines. The study is carried out using a 1D model of a small-size naturally aspirated SI engine, equipped with an external EGR circuit. The model, developed in GT-Power™ environment, includes advanced sub-models of the in-cylinder processes. The combustion is modeled using a fractal approach, where the burning rate is directly related to the laminar flame speed. A novel LFS correlation based on 1D chemical kinetics computations is presented and assessed with the experimentally derived Metghalchi and Keck correlation. Moreover, the effects of the flame stretch, evaluated according to an asymptotic theory, are properly considered in the combustion model.

Abstract In this work, the refinement of a phenomenological turbulence model developed in recent years by the authors is presented in detail. As known, reliable information about the underlying turbulence intensity is a mandatory prerequisite to predict the burning rate in phenomenological combustion models. The model is embedded under the form of “user routine” in the GT-Power™ software. The main advance of the proposed approach is the potential to describe the effects on the in-cylinder turbulence of some geometrical parameters, such as the intake runner orientation, the compression ratio, the bore-to-stroke ratio, and the valve number. The model is based on three balance equations, referring to the mean flow kinetic energy, the tumble vortex momentum, and the turbulent kinetic energy (3-eq. concept). An extended formulation is also proposed, which includes a fourth equation for the dissipation rate, allowing to forecast also the integral length scale (4-eq. concept).

Abstract Particulate matter (PM) indices—those linking PM emissions from gasoline engines to the composition and properties of the fuel—have been a topic of significant study over the last decade. It has long been known that fuel composition has a significant impact on particulate emissions from gasoline engines. Since gasoline direct injection (GDI) engines have become the market-leading technology, this has become more significant because the evaporative behavior of fuel increases in importance. Several PM indices have been developed to provide metrics describing this behavior and correlating PM emissions. In this article, 16 different PM indices are identified and collected—to the authors’ knowledge, all of the indices are available at the time of writing. The indices are reviewed and discussed in the context of the information required to calculate them, as well as their utility.

Abstract Natural gas (NG) can be compressed to a high pressure of around 200 bar for use in engines and other applications. Compressed natural gas (CNG) contains 87–92% methane (CH4) and has a low carbon-to-hydrogen ratio compared to other hydrocarbon (HC) fuels. Due to this, it can potentially reduce carbon dioxide (CO2) emissions by more than 20% compared to conventional fuels like diesel or gasoline. This makes CNG one of the most environmentally friendly fuels for internal combustion engines (ICEs). To improve the thermal efficiency of ICEs, higher compression ratios (CRs) and leaner combustion are essential. Since CNG is a gaseous fuel, it has several advantages over liquid fuels due to its favorable physical and chemical properties. A few of these advantages are minimal fuel evaporation issues, a low-carbon content in the fuel composition and a high-octane number. The CNG high-octane number allows for a high CR, resulting in higher thermal efficiency and lower emissions.

Abstract Evaluating the effects of deposits formed in existing engines on their performance is essential, particularly for gasoline direct injection (GDI) engines, wherein such deposits can be even more problematic. Furthermore, it has been suggested that some gasoline detergent additives (GDAs) may increase combustion chamber deposit (CCD) formation. However, there is a lack of data available regarding CCD formation in GDI engines, and there are no systematic investigations of the effects of the relationship between detergent additives and CCD formation on the GDI engines operation. Thus, the aim of this article was to critically review the existing literature on the effects of the deposit buildup associated with GDAs on the knocking performance, emissions, and operational properties of GDI engines. Surveyed studies showed that, GDI engines produce higher amounts of CCDs compared with port fuel injection (PFI) engines.

Abstract The long-term use of conventional liquid energy sources for internal combustion (IC) engines has its own negative ramifications on the health of living beings and the ecosystem at large. The search for solutions to overcome these implications brings us to one of the domains of research called alternative fuels. Alternative fuels may be used to enrich or fully substitute conventional fuels. In this review, a literature study on the enrichment of a primary fuel using hydroxy gas (HOH) produced from the electrolysis of water is discussed. The experimental evidence shows that HOH induction between 5 and 10 liters per minute (lpm) enhances the results of performance parameters coupled with a decrease in emission levels except for the oxides of nitrogen (NOx). However, this shortfall is nullified using techniques such as exhaust gas recirculation (EGR) and water injection.

Abstract In this study low temperature plasma technology was applied to expand auto-ignition operation region and control auto-ignition phasing of the homogeneous charge compression ignition (HCCI) combustion. The low temperature plasma igniter of a barrier discharge model (barrier discharge igniter (BDI)) with high-frequency voltage (15 kHz) was provided at the top center of the combustion chamber, and the auto-ignition characteristics of the HCCI combustion by the low temperature plasma assistance was investigated by using a single-cylinder gasoline engine. HCCI combustion with compression ratio of 15:1 was achieved by increasing the intake air temperature. The lean air-fuel (A/F) ratio limit and visualized auto-ignition combustion process on baseline HCCI without discharge assistance, spark-assisted HCCI, and BDI-assisted HCCI were compared.

Abstract In the last few years, the artificial neural networks have been widely used in the field of engine modeling. Some of the main reasons for this are, their compatibility with the real-time systems, higher accuracy, and flexibility if compared to other data-driven approaches. One of the main difficulties of using this approach is the calibration of the network itself. It is very difficult to find in the literature procedures that guide the user to completely define a network. Typically, the very last steps (like the choice of the number of neurons) must be selected by the user on the base of his sensitivity to the problem.

Abstract In this experimental study, a novel combustion technique, “reactivity-controlled compression ignition” (RCCI), has been investigated using alcohols acting as low-reactivity fuel (LRF) and mineral diesel acting as high-reactivity fuel (HRF). Combustion experiments were performed in a single-cylinder research engine at a constant engine speed of 1500 rpm and a low engine load of 3 bar brake mean effective pressure (BMEP). RCCI combustion is a practical low-temperature combustion (LTC) concept, which was achieved using three primary alcohols: Methanol, Ethanol, and Butanol in different premixed ratios (rp = 0.25, 0.50, and 0.75) with mineral diesel. Results showed a relatively superior performance and emissions characteristics of RCCI combustion compared to conventional compression ignition (CI) combustion. The influence of LRF was visible in RCCI combustion, which exhibited a more stable combustion compared to the baseline CI combustion.

Abstract A numerical simulation is a fundamental tool in the design and optimization procedure of an Internal Combustion (IC) engine; since combustion is the process that mostly influences the engine performance, efficiency and emissions, an effective combustion submodel is fundamental. A simple, nonpredictive way to simulate the combustion evolution is to implement a mathematical function that reproduces the mass fraction burned (MFB) profile that is characterized by a sigmoidal trend; the most used for this purpose is the Wiebe function.

Abstract Cycle-by-cycle combustion prediction in real time during engine operation can serve as a vital input for operating at optimal performance conditions and for emission control. In this work, a real-time capable physics-based combustion model has been proposed for the prediction of the heat release rate in a direct injection diesel engine. The model extends the approaches proposed earlier in the literature by considering spray dynamics such as spray penetration and Sauter mean diameter in order to calculate the mass of evaporated fuel from the spray. Wall impingement of the liquid spray is predicted by considering the liquid length based on the prevailing in-cylinder conditions. These effects are considered even after the hydraulic end of injection till the last droplet of fuel impinges on the combustion chamber wall. The fuel evaporated from the wall film and its contribution to the kinetic energy of the charge are also considered.

Abstract Insulating combustion chamber surfaces with thermal barrier coatings (TBCs) provides thermal efficiency improvement when done appropriately. This article reports on insulation heat transfer, engine performance characteristics, and damage modelling of “temperature swing” TBCs. “Temperature swing” insulation refers to the insulation material applied on surfaces of combustion chamber walls that enables selective manipulation of its surface temperature profile over the four strokes of an engine cycle. A combined GT Suite-ANSYS Fluent simulation methodology is developed to investigate the impact of thermal properties and insulation thickness for a variety of TBC materials for its “temperature swing” characteristics. This one-dimensional transient heat conduction analyses and engine cycle simulations are performed using scaled-down thermal properties of yttria-stabilized zirconia.

Abstract Increasing engine efficiency is essential to reducing emissions, which is a priority for automakers. Unconventional modes such as boosted and highly dilute operation have the potential to increase engine efficiency but suffer from stability concerns and cyclic variability. To aid engineers in designing ignition systems that reduce cyclic variability in such engine operation modes, reliable and accurate spark-ignition models are necessary. In this article, a Lagrangian–Eulerian spark-ignition (LESI) model is used to simulate electrical discharge, spark channel elongation, and ignition in inert or reacting crossflow within a combustion vessel, at different pressures, flow speeds, and dilution rates. First the model formulation is briefly revisited. Then, the experimental and simulations setups are presented.