Search Results

Abstract The ASTM D130 was first issued in 1922 as a tentative standard for the detection of corrosive sulfur in gasoline. A clean copper strip was immersed in a sample of gasoline for three hours at 50°C with any corrosion or discoloration taken to indicate the presence of corrosive sulfur. Since that time, the method has undergone many revisions and has been applied to many petroleum products. Today, the ASTM D130 standard is the leading method used to determine the corrosiveness of various fuels, lubricants, and other hydrocarbon-based solutions to copper. The end-of-test strips are ranked using the ASTM Copper Strip Corrosion Standard Adjunct, a colored reproduction of copper strips characteristic of various degrees of sulfur-induced tarnish and corrosion, first introduced in 1954. This pragmatic approach to assessing potential corrosion concerns with copper hardware has served various industries well for a century.

Abstract In recent years, lean-burn gasoline Spark-Ignition (SI) engines have been a major subject of investigations. With this solution, in fact, it is possible to simultaneously reduce NOx raw emissions and fuel consumption due to decreased heat losses, higher thermodynamic efficiency, and enhanced knock resistance. However, the real applicability of this technique is strongly limited by the increase in cyclic variation and the occurrence of misfire, which are typical for the combustion of homogeneous lean air/fuel mixtures. The employment of a Pre-Chamber (PC), in which the combustion begins before proceeding in the main combustion chamber, has already shown the capability of significantly extending the lean-burn limit. In this work, the potential of an ultralean PC SI engine for a decisive improvement of the thermal efficiency is presented by means of numerical and experimental analyses.

Abstract Due to the increasing requirements for efficiency, the wide range of characteristics and the improved possibilities of modern development and production processes, compressors in turbochargers have become more individualized in order to adapt to the requirements of internal combustion engines. An understanding of the working mechanisms as well as an understanding of the way that losses occur in the flow allows a reduced development effort during the optimization process. This article presents three-dimensional (3D) Computational Fluid Dynamics (CFD) investigations of the loss mechanisms and quantitative calculations of individual losses. The 3D-CFD method used in this article will reduce the drawbacks of one-dimensional calculation as far as possible. For example, the twist of the blades is taken into account and the “discrete” method is used for loss calculation instead of the “average” method.

Abstract Regulations limiting GreenHouse Gases (GHG) from Heavy-Duty (HD) commercial vehicles in the United States (US) and European Union will phase in between the 2024 and 2030 model years. These mandates require efficiency improvements at both the engine and vehicle levels, with the most stringent reductions required in the heaviest vehicles used for long-haul applications. At the same time, a 90% reduction in oxides of nitrogen (NOx) will be required as part of new regulations from the California Air Resources Board. Any technologies applied to improve engine efficiency must therefore not come at the expense of increased NOx emissions. Research into advanced engine architectures and components has identified improved turbomachine efficiency as one of the largest potential contributors to engine efficiency improvement. However this comes at the cost of a reduced capability to drive high-pressure Exhaust Gas Recirculation (EGR).

Abstract One of the most important factors affecting the performance of vehicle active chassis control systems is the tire-road friction coefficient. Accurate estimation of the friction coefficient can lead to better performance of these controllers. In this study, a new three-step friction estimation algorithm, based on intelligent tire concept, is proposed, which is a combination of experiment-based and vehicle dynamic based approaches. In the first step of the proposed algorithm, the normal load is estimated using a trained Artificial Neural Network (ANN). The network was trained using the experimental data collected using a portable tire testing trailer. In the second step of the algorithm, the tire forces and the wheel longitudinal velocity are estimated through a two-step Kalman filter. Then, in the last step, using the estimated tire normal load and longitudinal and lateral forces, the friction coefficient can be estimated.

Abstract Composite ceramic brake discs are made of ceramic material reinforced with carbon fibers and offer exceptional advantages that translate directly into higher vehicle performance. In the case of an electric vehicle, it could increase the range of the vehicle, and in the case of conventional internal combustion engine vehicles, it means lower fuel consumption (and consequently lower CO2 emissions). These discs are typically characterized by complex internal geometries, further complicated by the presence of drilling holes on both friction surfaces. To estimate the aerothermal performance of these discs, and for the thermal management of the vehicle, a reliable model for predicting the air flowing across the disc channels is needed. In this study, a real carbon-ceramic brake disc with drilling holes was investigated in a dedicated test rig simulating the wheel corner flow conditions experimentally using the particle image velocimetry technique and numerically.

Abstract In this work, a three-phase integrated onboard battery charger is investigated and implemented for electric vehicle (EV) applications. A three-switch add-on interface is introduced to connect with the inverter and the motor windings, such that a two-channel interleaved boost converter is formed for the battery charging. The detailed system analysis, design methodology, and control strategy are discussed. Moreover, a simulation study is carried out to validate the effectiveness of the proposed integrated charger. As verification, a 5 kW liquid-cooled prototype is built and tested. The proposed integrated charging system achieves a power factor of 0.99, and total harmonic distortion (THD) of 4.82% at 5 kW with an efficiency of 93.2%.

Abstract This article presents an investigation of energy transfer, flame propagation, and emissions formation mechanisms in a four-cylinder, downsized and boosted, spark ignition engine fuelled by either directly injected compressed natural gas (DI CNG) or gasoline (GDI). Three different charge preparation strategies are examined for both fuels: stoichiometric engine operation without external dilution, stoichiometric operation with external exhaust gas recirculation (EGR), and lean burn. In this work, experiments and engine modelling are first used to analyze the energy transfer throughout the engine system. This analysis shows that an early start of fuel injection (SOI) improves fuel efficiency through lower unburned fuel energy at low loads with stoichiometric DI CNG operation.

Abstract The article compares the accuracy of different exhaust gas recirculation (EGR) correction factor models under engine conditions. The effect of EGR on the laminar burning velocity of a EURO VI E10 specification gasoline (10% Ethanol content by volume) has been back calculated from engine pressure trace data, using the Leeds University Spark Ignition Engine Data Analysis (LUSIEDA) reverse thermodynamic code. The engine pressure data ranges from 5% to 25% EGR (by mass) with the running conditions, such as spark advance and pressure at intake valve closure, changed to maintain a constant engine load of 0.79 MPa gross mean effective pressure (GMEP). Based on the experimental data, a correlation is suggested on how the laminar burning velocity reduces with increasing EGR mass fraction.

Abstract To address the comfort and safety concerns related to driving vehicles, the Advanced Driver Assistance System (ADAS) is gaining huge popularity. The general architecture of autonomous vehicles includes perception, planning, control, and actuation. This article aims mainly at the controls aspect of one of the emerging ADAS features Lane Centering System (LCS). Limitations in deploying this feature from a controls point of view include maintaining the lane center with winding curvatures, dealing with the dynamic environment, optimizing controls where the perception of lane boundaries is erroneous, and, finally, concurring with the driver’s preferences. Although some research is available on LCS controls, most works are related only to the lateral controls by actuating steering. To increase the robustness, a comprehensive control strategy that involves lateral control, as well as longitudinal control along with a novel strategy to select the mode of driving, is proposed.

Abstract Electric power steering (EPS) systems have become the most advantageous steering system used in vehicles. They provide better fuel efficiency and a more compact design over traditional hydraulic power steering (HPS) systems. However, EPS systems are afflicted with unwanted noise and vibration that can undermine the safety of drivers. This article presents a mathematical framework for vibration analysis in a column-type EPS system. The steering column is modeled as a continuous clamped column. The equations of motion are derived using Hamilton’s principle, and explicit expressions are presented for the frequency and transmissibility equations. A three-degrees-of-freedom (3-DOF) dynamic model is also presented by an approximation of the stiffness, damping, and mass of the steering column. The results of the proposed analytical models are validated using ANSYS simulation.

Abstract The article presents a concept of a new turbine engine in the field of pressure gain combustion (PGC). The engine operates according to the Humphrey thermodynamic cycle, where pressure increase was obtained in a combustion chamber closed with a valve. The intake mushroom valve and exhaust swing valve were designed for self-acting. They operate as a result of gas pressure and centrifugal force. The engine consists of two rotating combustion chambers and a counterrotating radial turbine, in both of which mechanical power was generated. The gas flow in the mobile valve system, combustion process, gas expansion, and torque generation were analyzed by means of Computational Fluid Dynamics (CFD) analysis. The investigated engine concept is characterized by significant energy efficiency.

Abstract This work presents a generalized methodology for the optimal thermal management of different powertrain devices. The methodology is based on the adoption of an electrically driven pump and on the development of a specifically designed controller algorithm. This is achieved following a Model Predictive Control approach and requires a generalized lumped-parameters model of the thermal exchange between the device walls and the coolant. The methodology is validated at a test rig, with reference to a four-cylinder spark-ignition engine. Results show that the proposed approach allows a reduction in fuel consumption of about 2-3% during the engine warm-up, a decrease in fuel consumption of about 1-2% during fully warmed operation, and an estimated fuel consumption reduction of about 2.5-3% in an NEDC. Finally, the investigation highlights that the proposed approach reduces the risk of after-boiling when the engine is rapidly switched off after a prolonged high-load operation.

Abstract Among the myriad of potential hybrid powertrain architectures, selecting the optimal for an application is a daunting task. Whenever available, computer models greatly assist in it. However, some aspects, such as pollutant emissions, are difficult to model, leaving no other option than to test. Validating plausible options before building the powertrain prototype has the potential of accelerating the vehicle development even more, doing so without shipping components around the world. This work concerns the design of a system to virtually couple—that is, avoiding physical contact—geographically distant test rigs in order to evaluate the components of a powertrain. In the past, methods have been attempted, either with or without assistance of mathematical models of the coupled components (observers). Existing methods are accurate only when the dynamics of the systems to couple are slow in relation to the communication delay.

Abstract The electric-field coupled power transfer (ECPT) system with a coupling capacitor double-resonance circuit is proposed for electric vehicle (EV) charging. The article analyzes the plate capacitors between the EV and ground copperplate and introduces the coupling capacitor double-resonance circuit. The two-port network impedance matching of two topologies coupling capacitor double resonance is simulated, and then double side L impedance matching network and coupling capacitor double resonance with Series-Series (S-S) topology are proposed to solve the transmission efficiency decrease led by plate capacitances’ fluctuation. A prototype of the ECPT system is designed and built to prove the validity of the proposed methods. It is shown that the ECPT system realized higher than 60 W of electrical power, which is dynamic wireless transferred through the tire steel belt and the ground copperplate with at least 88% efficiency when the tires are rolling.

Abstract A pre-chamber ignition system has the potential to reduce the burn duration of lean-burn gasoline engine combustion and can achieve a reduced knock occurrence from the distributed ignition sources. Pre-chamber ignition produces high-velocity turbulent jets, and these jets often reach sonic velocity and produce shock waves inside the combustion chamber. These shock waves make knock detection difficult with a conventional surface-mounted acoustic knock sensor. This article discusses how an acoustic knock sensor works with a pre-chamber ignition and evaluates different cylinder pressure-based knock detection strategies and proposes a method that eliminates the influence of jet-induced oscillations on knock detection.

Abstract Deep learning (DL)-based approaches enable unprecedented control paradigms for propulsion systems, utilizing recent advances in high-performance computing infrastructure connected to modern vehicles. These approaches can be employed to optimize diesel aftertreatment control systems targeting the reduction of emissions. The optimization of the Trapped Soot Load (TSL) reduction in the Diesel Particulate Filter (DPF) is such an example. As part of the diesel aftertreatment system, the DPF stores the soot particles resulting from the combustion process in the engine. Periodically, the stored soot is oxidized during a DPF regeneration event. The efficiency of such a regeneration influences the fuel economy, and potentially the service interval of the vehicle. The quality of a regeneration depends on the operating conditions of the DPF, the engine, and the ability to complete the regeneration event.

Abstract Automotive subframe is a critical chassis component as it connects with the suspension, drive units, and vehicle body. All the vibration from the uneven road profile and drive units are passed through the subframe to the vehicle body. OEMs usually have specific component-level drive point dynamic stiffness (DPDS) requirements for subframe suppliers to achieve their full vehicle NVH goals. Traditionally, the DPDS improvement for subframes welded with multiple stamping pieces is done by thickness and shape optimization. The thickness optimization usually ends up with a huge mass penalty since the stamping panel thickness has to be changed uniformly not locally. Structure shape and section changes normally only work for small improvements due to the layout limitations. Tuned rubber mass damper (TRMD) has been widely used in the automotive industry to improve the vehicle NVH performance thanks to the minimum mass it adds to the original structure.

Abstract Demonstrating ring pack operation in an operating engine is very difficult, yet it is essential to optimize engine performance parameters such as blow-by, oil consumption, emissions, and wear. A significant amount of power is lost in friction between piston ring–cylinder liner interfaces if ring pack parameters are not optimized properly. Thus, along with these parameters, it is also necessary to reduce friction power loss in modern internal combustion engines as the oil film thickness formed between the piston ring and liner is vital for power loss reduction due to friction. Hence, it has also been a topic of research interest for decades. Piston and ring dynamics simulation software are used extensively for a better ring pack design. In this research work, a similar software for piston ring dynamics simulation reviews the ring pack performance of a four-cylinder diesel engine.

Abstract A Direct Yaw-Moment Control (DYC) logic for a rear-wheel-drive electric-powered vehicle is proposed. The vehicle is a Formula SAE (FSAE) type race car, with two electric motors powering each rear wheel. Vehicle baseline balance is neutral at low speeds, for increased maneuverability, and increases understeering at high speeds (due to the aerodynamic configuration) for stability. A controller that can deal with these yaw response variations, modelling uncertainties, and vehicle nonlinear behavior at limit handling is proposed. A two-level control strategy is considered. For the upper level, yaw rate and sideslip angle are considered as feedback control variables and a cubic-error Proportional Derivative (PD) controller is proposed for the feedback control. For the lower level, a traction control algorithm is used, together with the yaw moment requirement, for torque allocation.