Search Results

A Computational Fluid Dynamics (CFD) method, combined with a dynamic modeling technique is introduced to study the flow and performance of automotive hydraulic dampers / shock absorbers. The flow characteristics of components obtained by CFD are lied to a dynamic modeling package to predict the damping force. The component CFD analysis showed unique features of flow pattern, discharge coefficients, and pressure distribution for various shock absorber components. A dynamic damper model is constructed by integrating the hydraulic system with component flow information provided by CFD. The modeling results agree with test data well. It is shown that automotive shock absorber performance can be simulated accurately without physical testing.

Vehicle thermal protection is an important aspect of the overall vehicle development process. It involves optimizing the exhaust system routing and designing heat shields to protect various components that are in near proximity to the exhaust system. Reduced time to market necessitates an efficient process for thermal protection development. A robust procedure that utilizes state of the art CFD simulation techniques proactively during the design phase is described. Simulation allows for early detection of thermal issues and development of countermeasures several months before prototype vehicles are built. Physical testing is only used to verify the thermal protection package rather than to develop heat shields. The new procedure reduces the number of physical tests and results in a robust, efficient methodology.

This paper summarizes the major activities of CFD study on rear window buffeting of production vehicles during the past two years at DaimlerChrysler. The focus of the paper is the attempt to find suitable solutions for buffeting suppression using a developed procedure of CFD simulation with commercial software plus FFT acoustic post-processing. The analysis procedure has been validated using three representative production vehicles and good correlation with wind tunnel tests has been attained which has gained the confidence in solving the buffeting problem. Several attempts have been proposed and tried to find solution for buffeting reduction. Some of them are promising, but feasibility and manufacturability still need discussion. In order to find suitable solution for buffeting reduction, more basic research is necessary, more ideas should be collected, and more joint efforts of CFD and testing are imperative.

Fluid flow, temperature prediction, thermal response and light-off behavior of the catalytic converter were investigated using Computational Fluid Dynamics (CFD), combined with a conjugate heat transfer and a chemical reaction model. There are two objectives in this study: one to predict the maximum operation temperature for appropriate materials selection; and the other, to develop a numerical model which can be adjusted to reflect changes in the catalyst/washcoat formulation to accurately predict effects on the flow, temperature and light-off behavior. Temperature distributions were calculated for exhaust gas, catalyzed substrate, mounting mat and converter skin. Converter shell skin temperature was obtained for different mat materials. By changing reactant mass concentrations and noble metal loading, the converter light-off behavior, thermal response and temperature distributions were changed.

The flow within the disengaged wet clutch packs of an automatic transmission has been simulated as a three-dimensional, steady-state, two-phase flow using the commercial computational fluid dynamics (CFD) code FLUENT. The flow within a clutch with ungrooved friction plates was first solved for validating the CFD model, followed by a simulation of the flow within a clutch with grooved friction plates. A group of dimensionless variables have been established for mathematically modeling the drag torque and power loss in clutch packs. The effects of rotating speed of friction plate, pack clearance, and flow rate on drag torque and power loss have been studied.

In internal combustion engines, liquid fuel injection is one of the most prevalent means of fuel delivery and air-fuel mixture preparation. The behavior of the fuel spray and wall film is a key factor in determining air-fuel mixing and hence combustion and emissions. A comprehensive model for the liquid fuel spray has been developed in conjunction with the one-dimensional gas flow code WAVE. The model includes droplet dynamics and evaporation, spray-wall impingement, wall film dynamics and evaporation. The fuel injector can be placed in the manifold, inlet port or cylinder. Liquid fuel droplets are injected with a prescribed size distribution, and their subsequent movement and vaporization are modeled via the discrete particle approach, frequently used in multi-dimensional CFD codes. This approach ensures conservation of mass, momentum and energy between the gas and liquid phases.

The Fischer-Tropsch (FT) process can be used to synthesize diesel fuels from a variety of energy sources, including coal, natural gas and biomass. Diesel fuels produced from the FT process are essentially sulfur-free, have very low aromatic content, and have excellent ignition characteristics. Because of these favorable attributes, FT diesel fuels may offer environmental benefits over transportation fuels derived from crude oil. Previous tests have shown that FT diesel fuel can be used in unmodified engines and have been shown to lower regulated emissions. Whereas exhaust emissions reductions from these previous studies have been impressive, this paper demonstrates that far greater exhaust emissions reductions are possible if the diesel engine is optimized to exploit the properties of the FT fuels. A Power Stroke 7.3 liter turbocharged diesel engine has been modified for use with FT diesel.

Experimental and computational simulation techniques were concurrently employed throughout the aerodynamic development of the NASCAR Dodge Intrepid R/T in order to achieve a greater understanding of the complex flow fields involved. With less than 500 days to design, understand, and build a competitive vehicle, the development team utilized a closed loop approach to testing. Scale wind tunnel models and Computational Fluid Dynamics (CFD) were used to identify program direction and to speed the development cycle versus the traditional process of full scale testing. This paper will detail the process and application of both the experimental and computational techniques used in the aerodynamic development of the Intrepid R/T race vehicle, primarily focusing on the earlier stages that led to its competition introduction at the start of the 2001 season.

In 2007 emissions regulations for on-road light to heavy duty Diesel trucks will require the use of Diesel Particulate Filters (DPFs). The uniform distribution of soot on the DPF is critical for adequate long term performance of these DPFs. This is especially true when cordierite is used instead of silicon carbide for the DPF substrate, due to the reduced thermal conductivity and reduced peak temperature capability of cordierite. In addition to flow uniformity, an inverted flow pattern where more of the flow is forced radially outward on the substrate face could be beneficial to counteract thermal losses in the converter. This paper describes a dispersion device that can improve flow geometry with a low backpressure penalty. Computational fluid dynamics (CFD) results and experimental data are presented for this device. Additionally, cone design options are explored, and CFD analysis results of the cone design are presented.

An impinging-flow based methodology of enhancing the heat transfer in the grooves of a lockup clutch is proposed and studied. In order to evaluate its efficacy and reveal the mechanism, the three-dimensional flow within the groove was solved as a conjugate heat transfer problem in a rotating reference frame using the commercial CFD code FLUENT. The turbulence characteristics were predicted using k-ε model. The comparison of cooling effect was made between a simple baseline groove pattern and a typical flow-impingement based groove pattern of the same groove-to-total area ratio in terms of heat rejection ratio, maximum surface temperature, and heat transfer coefficient. It is found that more heat can be rejected with the impinging-flow based groove from the friction surface than with the baseline while the maximum surface temperature is lower in the former case.

In the development of several outside mirror designs for vehicles, a high frequency noise (whistling) phenomenon was experienced. First impression was that this might be due to another source on the vehicle (such as water management channels) or a cavity noise; however, upon further investigation the source was found to be the mirror housing. This “laminar whistle” is related to the separation of a laminar boundary layer near the trailing edges of the mirror housing. When there is a free stream impingement on the mirror housing, the boundary layer starts out as laminar, but as the boundary layer travels from the impingement point, distance, speed, and roughness combine to trigger the transition turbulent. However, when the transition is not complete, pressure fluctuations can cause rapidly changing flow patterns that sound like a whistle to the observer. Because the laminar boundary layer has very little energy, it does not allow the flow to stay attached on curved surfaces.

Shoebox catalytic converter design to securely mount thinwall substrates with uniform mounting mat Gap Bulk Density (GBD) around the substrate is developed and validated. Computational Fluid Dynamic (CFD) analysis, using heat transfer predictions with and without chemical reaction, allows to carefully select the mounting mat material for the targeted shell skin temperature. CFD analysis enables to design the converter inlet and outlet cones to obtain uniform exhaust gas flow to achieve maximum converter performance and reduce mat erosion. Finite Element Analysis (FEA) is used to design and optimize manufacturing tool geometry and control process. FEA gives insight to simulate the canning process using displacement control to identify and optimize the closing speed and load to achieve uniform mat Gap Bulk Density between the shell and the substrate.

Buffeting is a wind noise of high intensity and low frequency in a moving vehicle when a window or sunroof is open and this noise makes people in the passenger compartment very uncomfortable. In this paper, side window buffeting was simulated for a typical SUV using the commercial CFD software Fluent 6.0. Buffeting frequency and intensity were predicted in the simulations and compared with the corresponding experimental wind tunnel measurement. Furthermore, the effects of several parameters on buffeting frequency and intensity were also studied. These parameters include vehicle speed, yaw angle, sensor location and volume of the passenger compartment. Various configurations of side window opening were considered. The effects of mesh size and air compressibility on buffeting were also evaluated. The simulation results for some baseline configurations match the corresponding experimental data fairly well.

This paper provides an overview of the design and commissioning results for the DaimlerChrysler full-scale vehicle Aeroacoustic Wind Tunnel (AAWT) brought online in 2002. This wind tunnel represents the culmination of the plan for aeroacoustic facilities at the DaimlerChrysler Corporation Technical Center (DCTC) in Auburn Hills, Michigan. The competing requirements of excellent flow quality, low background noise, and constructed cost within budget were optimized using Computational Fluid Dynamics, extensive acoustic modeling, and a variety of scale-model experimental results, including dedicated experiments carried out in the 3/8-scale pilot wind tunnel located at DCTC. The paper describes the project history, user requirements, and design philosophy employed in realizing the facility. The AAWT meets all of DaimlerChrylser's performance targets, and was delivered on schedule. The commissioning results presented in this paper show its performance to be among the best in the world.

The existence of the cyclic variation of the flow inside an cylinder affects the performance of the engine. Developing methods to understand and control in-cylinder flow has been a goal of engine designers for nearly 100 years. In this paper, passive control of the intake flow of a 3.5-liter DaimlerChrysler engine was examined using a unique optical diagnostic technique: Molecular Tagging Velocimetry (MTV), which has been developed at Michigan State University. Probability density functions (PDFs) of the normalized circulation are calculated from instantaneous planar velocity measurements to quantify gas motion within a cylinder. Emphasis of this work is examination of methods that quantify the cyclic variability of the flow. In addition, the turbulent kinetic energy (TKE) of the flow on the tumble and swirl plane is calculated and compared to the PDF circulation results.

Lean operating natural gas heavy duty applications have advantages in terms of lower CO2 and PM compared to Diesel applications. This makes operating heavy duty applications on natural gas attractive and currently, they do not have to implement an exhaust particulate filter. However, the challenge is controlling methane emissions over a range of vehicle operating conditions. Methane is extremely stable and light off occurs at temperatures above 400 °C, with high efficiency occurring >500 °C and requires high precious metal loaded catalysts in the range of 150 - 200 g/ft3. Under stoichiometric conditions, 500 °C can be met in many engine operating points however, for lean operating applications, the exhaust temperature can be significantly lower than 500 °C posing a significant challenge for exhaust catalytic CH4 control. This paper will discuss synthetic gas reactor study results using ozone in the feed gas to perform low temperature methane control.