Search Results

Standard

AIR BRAKE HOSE

1970-01-01

HISTORICAL

J1402B_197001

This specification covers seven types of air hose intended for use in automotive air brake systems. The system includes all air actuated equipment leading from the air brake line. These types of hose are not to be used from the air compressor to air reservoir if air temperature is in excess of 250 F. Type G hose is to be used in frame and cab piping only, and only where air temperature is not in excess of 200 F. The types of hose are as follows: Type A–Hose shall be mandrel built having a tube and friction of oil resisting rubber, reinforced with cotton or synthetic cord or duck plies or a combination of both, and a cover of oil resisting compounds utilizing polymerized chloroprene as the basic material. Assemble with reusable or permanent type metal end fittings.

Standard

AUTOMOTIVE AIR BRAKE HOSE AND HOSE ASSEMBLIES

1976-07-01

HISTORICAL

J1402C_197607

This recommended practice covers minimum requirements for air brake hose assemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines that are exposed to potential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of –40°F to +200°F (–40°C to + 93°C).

Standard

Automotive Air Brake Hose and Hose Assemblies

2017-10-12

CURRENT

J1402_201710

This recommended practice covers minimum requirements for air brake hose assemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines with air pressures up to 1 MPa, that are exposed to potential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of -40 to +100 °C.

Standard

Automotive Air Brake Hose and Hose Assemblies

2010-08-05

HISTORICAL

J1402_201008

This recommended practice covers minimum requirements for air brake hose assemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines with air pressures up to 1 MPa, that are exposed to potential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of -40 to +100 °C.

Standard

BEADED TUBE HOSE FITTINGS

1992-06-01

HISTORICAL

J1231_199206

This SAE Standard covers complete general and dimensional specifications for beaded tube hose fittings. These fittings are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figures 1 to 3 and Table 1 are intended for use with low pressure hose and shall be retained by hose clamps as specified in SAE J536.

Standard

BEADED TUBE HOSE FITTINGS

1993-06-01

HISTORICAL

J1231_199306

This SAE Standard covers complete general and dimensional specifications for beaded tube hose fittings. These fittings are intended for general applications in low-pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figures 1 to 3 and Table 1 are intended for use with low-pressure hose and shall be retained by hose clamps as specified in SAE J1508.

Standard

CLIP FASTENER FITTING

1993-06-04

HISTORICAL

J1467_199306

This SAE Standard covers material and dimensional requirements of steel clip fastener fittings. These fittings are intended for use in hydraulic systems on industrial equipment primarily in mining applications.

Standard

CLIP FASTENER FITTING

1988-12-01

HISTORICAL

J1467_198812

This SAE Standard covers material and dimensional requirements of steel clip fastener fittings. These fittings are intended for use in hydraulic systems on industrial equipment primarily in mining applications.

Standard

CUMULATIVE DAMAGE ANALYSIS FOR HYDRAULIC HOSE ASSEMBLIES

1988-10-01

HISTORICAL

J1927_198810

Standard

Clip Fastener Fitting

2018-08-24

CURRENT

J1467_201808

This SAE Standard covers material and dimensional requirements of steel clip fastener fittings. These fittings are intended for use in hydraulic systems on industrial equipment primarily in mining applications.

Standard

Clip Fastener Fitting

2013-02-13

HISTORICAL

J1467_201302

This SAE Standard covers material and dimensional requirements of steel clip fastener fittings. These fittings are intended for use in hydraulic systems on industrial equipment primarily in mining applications.

Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

2009-03-27

HISTORICAL

J1927_200903

This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.

Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

2001-03-14

HISTORICAL

J1927_200103

This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.

Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

2014-06-04

CURRENT

J1927_201406

This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.

Standard

Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers

2006-03-27

HISTORICAL

J2631_200603

This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.

Standard

Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers

2011-10-25

CURRENT

J2631_201110

This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.

Standard

HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, 4 BOLT SPLIT FLANGE TYPE

1965-07-01

HISTORICAL

J518B_196507

This standard covers complete general and dimensional specifications for the flanged heads and split flange clamp halves applicable to 4-bolt split flange type tube, pipe, and hose connections with appropriate references to the “O” ring seals and attaching components used in their assembly. Also included are recommended port dimensions and port design considerations. The flanged heads specified are incorporated into fittings having suitable means for attachment to tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections. Flanged heads shall be as specified in Fig. 3 and Table 1. Split flange clamp halves shall be as specified in Fig. 4 and Table 1. Port dimensions and spacing shall be as specified in Fig. 5 and Table 2.

Standard

HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, FOUR-BOLT SPLIT FLANGE TYPE

1991-04-01

HISTORICAL

J518_199104

This SAE Standard covers complete general and dimensional specifications for the flanged heads and split flange clamp halves applicable to four-bolt split flange type tube, pipe, and hose connections with appropriate references to the O-ring seals and attaching components used in their assembly. (See Figures 1 and 2.) Also included are recommended port dimensions and port design considerations. The flanged heads specified are incorporated into fittings having suitable means for attachment to tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections. Flanged heads shall be as specified in Figure 3 and Table 1. Split flange clamp halves shall be as specified in Figure 4 and Table 1. Port dimensions and spacing shall be as specified in Figure 5 and Table 2.

Standard

HYDRAULIC HOSE

1980-06-01

HISTORICAL

J517_198006

This standard covers general, dimensional, and performance specifications for several varieties of hose intended for general application in hydraulic systems on construction and industrial equipment and commercial products. These general specifications are common to and shall supplement the detailed specifications for the SAE 100R1, SAE 100R2, SAE 100R3, SAE 100R4, SAE 100R5, SAE 100R6, SAE 100R7, SAE 100R8, SAE 100R9, SAE 100R10, SAE 100R11, and SAE 100R12 hydraulic hoses set forth in the following sections.

Standard

HYDRAULIC HOSE

1980-08-01

HISTORICAL

J517_198008

This standard covers general, dimensional, and performance specifications for several varieties of hose intended for general application in hydraulic systems on construction and industrial equipment and commercial products. These general specifications are common to and shall supplement the detailed specifications for the SAE 100R1, SAE 100R2, SAE 100R3, SAE 100R4, SAE 100R5, SAE 100R6, SAE 100R7, SAE 100R8, SAE 100R9, SAE 100R10, SAE 100R11, and SAE 100R12 hydraulic hoses set forth in the following sections.