Refine Your Search

Date

Date

Topic

Topic

Author

Author

Steel Materials handling Standard

Search Results

Viewing 1 to 20 of 10725
123Next >Last >>
Sort by title
Standard

350 °F Autoclave Cure, Low Flow Toughened Epoxy Prepregs
2015-12-02
CURRENT
AMS3961
The intent of this specification is for the procurement of the material listed on the QPL and, therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program shall refer to the Quality Assurance section of this base specification, AMS3961. All material qualification and equivalency data has been archived and is available for review upon request. Contact the CMH-17 Secretariat (www.cmh17.org) for additional information.
Standard

350 °F Autoclave Cure, Low Flow Toughened Epoxy Prepregs
2019-03-12
WIP
AMS3961A
The intent of this specification is for the procurement of the material listed on the QPL and, therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program shall refer to the Quality Assurance section of this base specification, AMS3961. All material qualification and equivalency data has been archived and is available for review upon request. Contact the CMH-17 Secretariat (www.cmh17.org) for additional information.
Standard

70 MPa Compressed Hydrogen Surface Vehicle Fueling Connection Device and Optional Vehicle to Station Communications
2007-05-24
HISTORICAL
J2799_200705
This technical information report specifies a guideline for the hardware requirements for fueling a Hydrogen Surface Vehicle (HSV) with compressed hydrogen storage rated at a Nominal Working Pressure of 70 MPa. It contains a description of the receptacle geometry and optional communication hardware and communications protocol to refuel the HSV. The intent of this document is to enable harmonized development and implementation of the hydrogen fueling interfaces. It is intended to be utilized for hydrogen vehicle field evaluations until enough information is collected to enable standardization. The receptacle portion of this document is to be reevaluated utilizing international field data in approximately two (2) years and subsequently superseded by SAE J2600 in the 2009 timeframe.
Standard

ABRASION RESISTANCE TESTING—VEHICLE EXTERIOR GRAPHICS AND PIN STRIPING
1989-06-01
HISTORICAL
J1847_198906
This SAE Recommended Practice applies to the abrasion resistance testing of decorative tapes, graphics, and pin striping. It may also have relevance to certain vehicle labels and plastic wood grain film. The resistance to abrasive damage is judged qualitatively by its effect on the legibility, pattern, and color of the graphic marking. This recommended practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering the use of this recommended practice.
Standard

ACCELERATED ENVIRONMENTAL TESTING FOR BONDED AUTOMOTIVE ASSEMBLIES
1992-08-01
HISTORICAL
J2100_199208
This SAE Recommended Practice defines conditions to which bonded assemblies can be exposed to simulate environmental aging. These recommendations are generally based on existing Original Equipment Manufacturer requirements at this time. (Environmental specifications used for this proposal were from General Motors, Ford, and Chrysler.) The substrate type, dimension, and number are described by the standard for materials being tested and should include control specimens which receive no environmental aging.
Standard

ACCEPTANCE TEST PROCEDURES AND STANDARDS TO INSURE CLEAN FUEL SYSTEM COMPONENTS
2007-12-04
HISTORICAL
ARP1953A
To describe general guidelines for achieving selected levels of cleanliness in gas turbine engine fuel system components and to describe laboratory type methods for measuring and reporting the contamination level of the wetted portion of fuel system components. As in SAE J1227 (covering hydraulic components) this practice includes guidelines for levels of acceptance but does not attempt to set those levels.
Standard

ACCEPTANCE TEST PROCEDURES AND STANDARDS TO INSURE CLEAN FUEL SYSTEM COMPONENTS
1992-08-01
HISTORICAL
ARP1953
To describe general guidelines for achieving selected levels of cleanliness in gas turbine engine fuel system components and to describe laboratory type methods for measuring and reporting the contamination level of the wetted portion of fuel system components. As in SAE J1227 (covering hydraulic components) this practice includes guidelines for levels of acceptance but does not attempt to set those levels.
Standard

ACCESS SYSTEMS FOR CONSTRUCTION AND INDUSTRIAL EQUIPMENT
1970-07-01
HISTORICAL
J185_197007
This recommended practice covers the criteria for steps, ladders, walkways, platforms, grab rails (handrails), grab irons, guardrails, and entrance openings as they relate to aiding the operator and/or servicemen in performing their functions on the vehicle.
123Next >Last >>
X