Search Results

A 10 KWe dual-mode space power system concept has been identified which is based on INEL's Small Externally-fueled Heat Pipe Thermionic Reactor (SEHPTR) concept. This power system will enhance user capabilities by providing reliable electric power and by providing two propulsion systems; electric power for an arc-jet electric propulsion system and direct thrust by heating hydrogen propellant inside the reactor. The low thrust electric thrusters allow efficient station keeping and long-term maneuvering. The direct thrust capability can provide tens of pounds of thrust at a specific impulse of around 730 seconds for maneuvers that must be performed more rapidly. The direct thrust allows the nuclear power system to move a payload from Low Earth Orbit (LEO) to Geosynchronous Earth Orbit (GEO) in less than one month using approximately half the propellant of a cryogenic chemical stage.

The 1977 Clean Air Act Amendments allow the U.S. Environmental Protection Agency to set high altitude emission standards for 1981-83, but specify that any such standards may not be more stringent than comparable sea level standards -- relative to 1970 emission levels. Since available high altitude emission data from 1970 models were incomplete and controversial, the Motor Vehicle Manufacturers Association contracted with Automotive Testing Laboratories, Inc. to test a fleet of 25 1970 cars. Results of the test program showed average increases in emissions at Denver's altitude, compared to sea level, to be about 30% for evaporative HC, 57 to 60% for exhaust HC, 215 to 247% for CO and -46 to -47% for NOx. Corresponding HC and CO exhaust emission baselines would be 6.4 to 6.6 and 108 to 118 g/mi respectively.

The paper describes a numerical study, supported by experiments, on light aircraft 2-Stroke Direct Injected Diesel engines, typically rated up to 110 kW (corresponding to about 150 imperial HP). The engines must be as light as possible and they are to be directly coupled to the propeller, without reduction drive. The ensuing main design constraints are: i) in-cylinder peak pressure as low as possible (typically, no more than 120 bar); ii) maximum rotational speed limited to 2600 rpm. As far as exhaust emissions are concerned, piston aircraft engines remain unregulated but lack of visible smoke is a customer requirement, so that a value of 1 is assumed as maximum Smoke number. For the reasons clarified in the paper, only three cylinder in line engines are investigated. Reference is made to two types of scavenging and combustion systems, designed by the authors with the assistance of state-of-the-art CFD tools and described in detail in a parallel paper.

In part two of a two-part series, Richard Gardner discusses various aerospace propulsion innovations and continued work by aerospace engineers and scientists to advance aircraft engine technologies to increase efficiency and lower emissions.

BlueStar Advanced Technology Corporation (BATC) as part of its participation in the USAF/NASA Li Ion Battery Development Consortium has developed a candidate 25-Ah cell for the Mars 2001 Lander. Although the capacity and cycle life requirements for this application are relatively modest, the low temperature performance (−20°C) and pulse discharge requirements (60A) are somewhat more challenging. Geometric requirements within the spacecraft also constrain the cell design leading to a cell with an aspect ratio quite different from those 25-Ah Li ion cells previously developed by BATC. The design of this cell and its compliance with the performance requirements of the mission will be discussed.

Ultrasound is attractive for medical imaging in space because scanners can be small, lightweight, low power, and have minimal electromagnetic emissions. In addition, unlike conventional 2-D ultrasound. 3-D ultrasound allows an operator with no diagnostic skills to collect high-quality scans that can be interpreted by a remote expert. This allows 3-D ultrasound to be used effectively in remote locations. These capabilities are illustrated by the MUSTPAC-1, a portable 3-D ultrasound telemedicine system recently developed for the U.S. military. Design, implementation, and field experiences with the MUSTPAC-1 are discussed, and extensions for use in space are proposed.

This paper discusses five different methods for measuring the gas stream temperature from a burner using a hydrocarbon fuel, air, and oxygen. Tests were made with a single shielded BeO probe, a bare wire iridium -- 60% rhodium/iridium couple, a tantalum triple shielded platinum -- 10% rhodium/platinum thermocouple, the sodium line reversed technique, and a watercooled total enthalpy probe. The most serviceable system proved to be the bare wire iridium -- 60% rhodium/iridium couple, particularly for carrying out stream surveys where relative, rather than true temperatures, are of primary concern. More study is needed to establish a system for determining the true stream temperature.

As a part of a program jointly supported by the USAF and Canada's Department of National Defense, BlueStar is developing large (50 to 100-Ah)lithium ion cells for aircraft and spacecraft applications. Presently, 20-Ah cells are being developed as the first stage of the scale-up process and the design of these cells involves several tradeoffs related to the specific nature of this application. This paper will present the design of this first generation cell in the context of these tradeoffs as well as presenting the results of the performance and life testing of these cells.

A 500 hours endurance test was performed with a heavy-duty engine (Euro IV); MAN type D 0836 LFL 51 equipped with a PM-Kat®. As fuel 100% biodiesel was used that met the European specification EN 14214. The 500 hours endurance test included both the European stationary and transient cycle (ESC and ETC) as well as longer stationary phases. During the test, regulated emissions (carbon monoxide, nitrogen oxides, hydrocarbons and particulate matter), the particle number distribution and the aldehydes emission were continuously measured. For comparison, tests with fossil diesel fuel were performed before and after the endurance test. During the endurance test, the engine was failure-free for 500 hours with the biogenic fuel. There were almost no differences in specific fuel consumption during the test, but the average exhaust gas temperature increased by about 15°C over the time. Emissions changed only slightly during the test.

The experimental procedure employed to define the natural modes of vibration of the 747 Shuttle Carrier Aircraft and Space Shuttle Orbiter mated configuration is described. A discussion of test results and comparison to structural analysis results is also included. Random transient signals were used as inputs to electromagnetic shakers to provide excitation to the mated vehicle test configuration. Acceleration signals were processed via the Fast Fourier Transform algorithm. Magnitude and phase transfer functions were formed and processed to produce modal frequencies, damping, and modal displacements.

In 1995, the Naval Research Laboratory (NRL) began a program to investigate whether a 90 Ah dependent pressure vessel (DPV) NiH2 battery pack could be a lower volume replacement for a 90 Ah NiH2 IPV spacecraft battery. Nickel Hydrogen (NiH2) dependent pressure vessel (DPV) battery cells are presumed to offer all the features of the NiH2 IPV battery cell with considerably less volume. To achieve this reduction in volume, the DPV cell utilizes a canteen shaped pressure vessel with reduced thickness wall, flat sides and curved ends. The cells can be packaged similar to prismatic nickel cadmium battery cells. Moreover, like NiCd cells, a fully charged DPV cell must rely upon an adjacent battery cell or structure for support and to maintain pressure vessel integrity. Seventeen 90 Ah NiH2 DPV cells were delivered to NR in 1998 for qualification tests. An eleven-cell half battery pack was manufactured and tested to validate the advantages of the DPV design.

The 912 engine is a well known 4-cylinder horizontally opposed 4-stroke liquid-/air-cooled aircraft engine. The 912 family has a strong track record: 40 000 engines sold / 25 000 still in operation / 5 million flight hours annually. 88% of all light aircraft OEMs use Rotax engines. The 912iS is an evolution of the Rotax 912ULS carbureted engine. The “i” stands for electronic fuel injection which has been developed according to flight standards, providing a better fuel efficiency over the current 912ULS of more than 20% and in a range of 38% to 70% compared to other competitive engines in the light sport, ultra-light aircraft and the general aviation industry. BRP engineers have incorporated several technology enhancements. The fully redundant digital Engine Control Unit (ECU) offers a computer based electronic diagnostic system which makes it easier to diagnose and service the engine.

In the course of CRYOSYSTEM phase B (development phase) financed by the European Space Agency, AIR LIQUIDE (France) and Astrium Space Infrastructure (Germany) have developed an optimized design of a −183°C freezer to be used on board the International Space Station for the freezing and storage of biological samples. The CRYOSYSTEM facility consists of the following main elements: - the CRYORACK, an outfitted standard payload rack (ISPR) accommodating up to three identical Vial Freezers - the Vial Freezer, a dewar vessel capable of fast and ultra-rapid freezing, and storing up to approximately 900 vials below −183°C; the dewar is cooled by a Stirling machine producing > 6 W at 90 K. The Vial Freezer is operational while accommodated in the CRYORACK or attached to the Life Science Glovebox (LSG). One CRYORACK will remain permanently on-orbit for several years while four Vial Freezers and two additional CRYORACKs support the cyclic upload/download of samples.

In the frame of the CRYOSYSTEM A-phase study financed by the European Space Agency, AIR LIQUIDE (France) and ORBITAL HYDRAULIC-BREMEN (Germany) have been studying a -183°C freezer to be used on-board the International Space Station for freezing and storing biological samples.

A baseline design has been selected for the Space Station Habitat (HAB) element. The HAB provides the primary living space to support man's permanent presence in space. The HAB element is designed to provide an environment that maximizes safety and human productivity. This paper outlines some of the current design features including the common core elements and the man-systems hardware. The HAB is arranged in three areas based on crew activity and acoustical considerations. The first area is the quiet zone, which contains the crew quarters. The second area is a buffer zone for noise suppression, where the stowage, medical facilities, and personal hygiene facilities are located. The third area is the active zone which contains the galley/wardroom, laundry and exercise facilities. Each of these three areas will be discussed together with the applicable requirements, the common utility elements, and the man-systems hardware furnishings.

Affordable, reliable endo- and exoatmospheric transportation, for both the military and commercial sectors, grows in importance as the world grows smaller and space exploration and exploitation increasingly impact our daily lives. However, the impact of disciplinary, operational, and technological uncertainties inhibit the design of the requisite hypersonic vehicles, an inherently multidisciplinary and non-deterministic process. Without investigation, these components of design uncertainty undermine the designers’ decision-making confidence. In this paper, the authors propose a new probabilistic design method, using Bayesian Statistics techniques, which allows assessment of the impact of disciplinary uncertainty on the confidence in the design solution. The proposed development of a two-stage reusable launch vehicle configuration highlights the means to first quantify the fidelity of the disciplinary analysis tools utilized, then propagate such to the vehicle system level.

With reusability accepted as a means of reducing operating costs, the size of the initial investment (research and development) is likely to determine the choice for the next generation boosters. High volume utilisation lifting bodies propelled by LH/LOX rockets in a vertical take-off mode are shown to be superior to several other concepts. This is largely due to the low manufactured weight without undue complexity or use of exotic materials, leading to low R&D and low unit cost. Even lower costs can be shown for a modular concept (MUSTARD) in which basically identical lifting bodies units are utilised as both boosters and spacecraft. The concept is shown to be feasible, and progress on some aspects of the associated structural analysis is described.

Within the frame of a series of initiatives aimed at improving effectiveness of its aircraft design and analysis capabilities, the Military Division of Daimler-Benz Aerospace (Dasa) is developing MIDAS, a multidisciplinary integration framework for a suite of numerical codes suitable to quickly and still accurately assess aircraft performance. As MIDAS specifically targets support of configurational studies in a Conceptual and Preliminary Design environment, peculiar requirements such as scope, range of applicability, and robustness of the system components, reliability of results, care-free operability, and fast response times have to be properly addressed.

As humans move into outer space, need for air, clean water and food require that green plants be grown within all planetary colonies. The complexities of ecosystems require a sophisticated understanding of the interactions between the atmosphere, all nutrients, and life forms. While many experiments must be done to find the relationships between mass flows and chemical/energy transformations, it seems necessary to develop generalized models to understand the limitations of plant growth. Therefore, it is critical to have a robust modelling capability to provide insight into potential problems as well as to direct efficient experimentation. Last year we reported on a simple leaf model which focused upon the mass transfer of gases, radiation/heat balances, and the production of photosynthetically produced carbohydrate. That model indicated some of the plant processes which had to be understood in order to obtain parameters specific for each species.

An optical sensor for the detection of carbon dioxide concentrations and stable isotope ratios is described. Either a continuous wave, fiber-coupled distributed feedback laser or an external cavity laser is used to pump an optical cavity absorption cell in cw-Cavity Ringdown Spectroscopy (cw-CRDS). This technique exploits the sensitivity enhancements provided by the long effective pathlength from the optical cavity created between two highly reflective mirrors (R>0.9999). The inherently high precision of the technique combined with its rapid data throughput allows for reliable measurements of both concentration and the isotopic composition of the sampled carbon dioxide. Data collected using a prototype of this sensor could be useful for monitoring module occupancy, crew health (through breath tests), and plant growth chambers.