Search Results

Component bench testing is a basic method to validate the component fatigue life. However, the component bench testing takes long time and is costly. With the development of more powerful computer and CAE simulation techniques, virtual CAE simulation method becomes more important in the component design, optimization, and validation due to its efficiency and low cost. Fatigue life of components of exhaust system is a critical characteristic and it is not deterministic but statistical phenomenon. Thus, a probabilistic approach is necessary. Variations and reliability of fatigue life can be considered in physical testing by testing more samples. However, how to account variations from manufacturing and testing in virtual CAE simulation is a big challenge. In this paper, a virtual CAE fatigue life prediction of components of exhaust system by probabilistic approach is studied and proposed.

High-temperature thermal-mechanical systems are considered as an indispensable solution to modern vehicle emission control. Such systems include advanced engines, manifolds, thermal regeneration systems, and many other systems. Creep, fatigue, oxidation, or their combinations are the fundamental underlying material degradation and failure mechanisms in these systems subjected to combined thermal and mechanical loadings. Therefore, the basic understanding and modeling of these mechanisms are crucial in engineering designs. In this paper, the state-of-the-art methods of damage/failure modeling and life assessment for components under thermal-fatigue loading, are reviewed first. Subsequently, a new general life assessment procedure is developed for components subjected to variable amplitude thermal- and mechanical- loadings, with an emphasis on hold-time effect and cycle counting.

Durability performance is one of the most important aspects of exhaust system design. Great effort has been expended to develop the ability to accurately and quickly predict the durability of the system in the early development stages. Welded joints in an exhaust system are the most prone to failure; however, the fatigue life of a welded joint is usually much more difficult to predict than that of a base material. The difficulty of predicting the fatigue life of a welded structure lies primarily in the variability associated with the elements of a weldment, including differing material and gap requirements, notch generation, residual stresses, and imprecise application, among others. The experts at the Battelle Center for Welded Structures Research have developed an approach to predict the fatigue life of a welded structure known as the Verity method.

A design curve, such as a fatigue design S-N curve, is required in engineering design processes. The design curve is usually constructed by analyzing test data, which often exhibit relatively large scatter. For assumed linear test data, two-stress level test plan is commonly used for accelerated life testing (ALT) and subsequent design curve construction. In this paper, based on the two-stress level test plan, a tolerance limit approach is adopted to develop a simple design curve construction procedure. The predicted results from the new method are compared with that of other methods. The advantage of the new method is demonstrated by analyzing the fatigue S-N test data of exhaust components. The determination of minimum sample size is also discussed with a worked table and a graph.

Weibull analysis is widely used in many industries to predict the fatigue life of different components. Three typical Weibull distributions are introduced in this paper. The application of two parameter Weibull distribution in exhaust component fatigue life prediction is presented. Potential issues in component testing are addressed. Criteria are provided to define normal test data, and when replacement of a tested sample is required. The studies demonstrate that Weibull method is effective to predict component R90C90 life. However, data investigation and processing are critical to predict component life properly. The predicted fatigue life may differ by more than an order of magnitude if the sample life data is unrepresentative of the testing and manufacturing conditions.

The equilibrium mechanism, which can be considered as the basis of least squares method for linear curve fitting, is investigated in this paper. Both conventional methods, such as vertical offsets method, and total least squares methods, such as perpendicular offsets method, are examined. It is found that both methods have the equilibrium bases. However, the conventional methods may give inaccurate prediction if using vertical offsets method to fit data with variation in horizontal direction or using horizontal offsets method to fit data with variation in vertical direction while the perpendicular method can give best fit solution to data with variation in both vertical and horizontal directions. The application of these methods is also presented in fatigue S-N curve data analysis and two-parameter Weibull distribution in exhaust component fatigue life prediction.

Active regeneration systems for cleaning diesel exhaust can operate at extremely high temperatures up to 1000°C. The extremely high temperatures create a unique challenge for the design of regeneration structural components near their melting temperatures. In this paper, the preparation of the sheet specimens and the test set-up based on induction heating for sheet specimens are first presented. Tensile test data at room temperature, 500, 700, 900 and 1100°C are then presented. The yield strength and tensile strength were observed to decrease with decreasing strain rate in tests conducted at 900 and 1100°C but no strain rate dependence was observed in the elastic properties for tests conducted below 900°C. The stress-life relations for under cyclic loading at 700 and 1100°C with and without hold time are then investigated. The fatigue test data show that the hold time at the maximum stress strongly affects the stress-life relation at high temperatures.

Structural stress methods are now widely used in fatigue life assessment of welded structures and structures with stress concentrations. The structural stress concept is based on the assumption of a global stress distribution at critical locations such as weld toes or weld throats, and there are several variants of structural stress approaches available. In this paper, the linear traction stress approach, a nodal force based structural stress approach, is reviewed first. The linear traction stress approach offers a robust procedure for extracting linear traction stress components by post-processing the finite element analysis results at any given hypothetical crack location of interest. Pertinent concepts such as mesh-insensitivity, master S-N curve, fatigue crack initiation and growth mechanisms are also discussed.

A statistic fatigue life assessment procedure is presented in this paper for estimating fatigue damage under stationary Gaussian multi-axial loadings with narrow-band frequency. The fatigue damage is determined by using the Miner-Palmgren rule in connection with a recently developed path-length based multi-axial cycle counting and fatigue life assessment method. In this procedure, the path length is determined by averaging sinusoidal waves with uniformly distributed phase angles while the cycles are estimated from the observation of peak counting results of stress components. Numerically simulated random loading paths with different degrees of non-proportionality are used here to compare the proposed statistical method with its time domain counterpart. Possible further improvement in this research direction is also indicated.

Driven by diesel engine emission regulation, more emission aftertretment products have been under development by Tenneco to address the Particular Matter (PM) and NOx reduction needs. The T.R.U.E. (Thermal Regeneration Unit for Exhaust) Clean active thermal management system is one of the examples to reduce PM. The system is designed to increase exhaust temperatures for DPF (Diesel Particulate Filter) regeneration. This product is exposed to high temperature and high oxidation. Therefore, thermal fatigue, creep, oxidation and the interaction become critical mechanism to be considered for its durability. One of the key challenges to validate this product is to find a way of accelerated testing for thermal, creep, and oxidation as well as for vibration. In this paper, accelerated durability test strategy for high temperature device like T.R.U.E Clean is addressed.