Refine Your Search

Search Results

Viewing 1 to 11 of 11
Technical Paper

A Co-Simulation Environment for Virtual Prototyping of Ground Vehicles

The use of virtual prototyping early in the design stage of a product has gained popularity due to reduced cost and time to market. The state of the art in vehicle simulation has reached a level where full vehicles are analyzed through simulation but major difficulties continue to be present in interfacing the vehicle model with accurate powertrain models and in developing adequate formulations for the contact between tire and terrain (specifically, scenarios such as tire sliding on ice and rolling on sand or other very deformable surfaces). The proposed work focuses on developing a ground vehicle simulation capability by combining several third party packages for vehicle simulation, tire simulation, and powertrain simulation. The long-term goal of this project consists in promoting the Digital Car idea through the development of a reliable and robust simulation capability that will enhance the understanding and control of off-road vehicle performance.
Technical Paper

Adapting Farm Equipment for Workers with Disabilities

Farm workers experience a very high incidence of injuries leading to physical and cognitive (strokes, TBI) disabilities. Since 1991, the AgrAbility Project 2 and its staff have provided direct assistance and education to many U.S. farmers and farm workers. If farmers, ranchers or farm workers who become disabled continue to be employed in agriculture, often their agricultural operation must be modified and/or agricultural machinery must be modified or adaptive equipment purchased to meet their new needs. Some common tractor modifications include operator lifts, hand controls, added/modified steps and handrails, automated hitches, and custom seating. Some modifications are commercially available but others are done on an individual need basis. AgrAbility staff would welcome the opportunity to work closer with farm equipment manufacturers to create modifications that would make farming and ranching easier and safer for all.
Technical Paper

Effects of Mixture Preparation Characteristics on Four-Stroke Utility Engine Emissions and Performance

A laboratory-based fuel mixture system capable of delivering a range of fuel/air mixtures has been used to observe the effects of differing mixture characteristics on engine combustion through measurement and analysis of incylinder pressure and exhaust emissions. Fuel air mixtures studied can be classified into four different types: 1) Completely homogeneous fuel/air mixtures, where the fuel has been vaporized and mixed with the air prior to entrance into the normal engine induction system, 2) liquid fuel that is atomized and introduced with the air to the normal engine induction system, 3) liquid fuel that is atomized, and partially prevaporized but the air/fuel charge remains stratified up to introduction to the induction system, and 4) the standard fuel metering system. All tests reported here were conducted under wide open throttle conditions. A four-stroke, spark-ignited, single-cylinder, overhead valve-type engine was used for all tests.
Technical Paper

Effects of Multiple Injections and Flexible Control of Boost and EGR on Emissions and Fuel Consumption of a Heavy-Duty Diesel Engine

A study of the combined use of split injections, EGR, and flexible boosting was conducted. Statistical optimization of the engine operating parameters was accomplished using a new response surface method. The objective of the study was to demonstrate the emissions and fuel consumption capabilities of a state-of-the-art heavy -duty diesel engine when using split injections, EGR, and flexible boosting over a wide range of engine operating conditions. Previous studies have indicated that multiple injections with EGR can provide substantial simultaneous reductions in emissions of particulate and NOx from heavy-duty diesel engines, but careful optimization of the operating parameters is necessary in order to receive the full benefit of these combustion control techniques. Similarly, boost has been shown to be an important parameter to optimize. During the experiments, an instrumented single-cylinder heavy -duty diesel engine was used.
Technical Paper

Feature Extraction from Non-Linear Geometric Models in Design-for-Manufacturing

Automatic manufacturability analysis of injection moldings, sheet metal castings, stampings, forgings, etc., using knowledge-based heuristics depends on shape features, which are abstractions of the three dimensional (3D) geometric model of the parts. Conventional CAD systems do not explicitly contain shape feature information, therefore such information needs to be extracted from them. So far, extraction of shape features has been restricted to models with simple geometric shapes such as planar, cylindrical or conical shapes. Extending shape feature extraction to non-linear geometric models will allow Design For Manufacturability (DFM) analysis of non-linear models. This paper presents an approach to extract features from non-linear geometric models. The approach is based on abstract geometric entities called C-loops. The formation of a C-loop depends on a geometric entity called a silhouette. The C-loops are derived from the silhouette boundaries of an object.
Technical Paper

Future Developments in Forage Harvesting Machinery and Processing

Forage harvesting, processing and handling equipment research is currently underway which will improve commodity quality, produce “value -added” products from forages, reduce energy and labor requirements of the equipment and improve forage marketability. Technologies are described which could increase forage quality and value by removing it from the field sooner after it is mowed to minimize the risk of weather damage. Mechanisms and management strategies for reducing the labor and energy required for field processing and for improving the marketability of forages are also described.
Journal Article

Heavy-Duty RCCI Operation Using Natural Gas and Diesel

Many recent studies have shown that the Reactivity Controlled Compression Ignition (RCCI) combustion strategy can achieve high efficiency with low emissions. However, it has also been revealed that RCCI combustion is difficult at high loads due to its premixed nature. To operate at moderate to high loads with gasoline/diesel dual fuel, high amounts of EGR or an ultra low compression ratio have shown to be required. Considering that both of these approaches inherently lower thermodynamic efficiency, in this study natural gas was utilized as a replacement for gasoline as the low-reactivity fuel. Due to the lower reactivity (i.e., higher octane number) of natural gas compared to gasoline, it was hypothesized to be a better fuel for RCCI combustion, in which a large reactivity gradient between the two fuels is beneficial in controlling the maximum pressure rise rate.
Technical Paper

Image Analysis of Diesel Sprays

Time resolved measurements of non-evaporating, non-burning fuel sprays injected into a quiescent atmosphere were performed. The experimental parameters included ambient gas density, mass of fuel injected per stroke, pump speed, and nozzle diameter. High speed films of fuel sprays were obtained using a rapidly pulsed Cu-vapor laser in synchronization with a high frame rate film camera. The laser light intensity transmitted through the spray was recorded directly by the film camera. The information encoded on the film was subsequently digitized using a projector/CCD camera system. Finally, instantaneous ensemble averaged properties of droplets constituting the spray were estimated by quantitative analysis of the digitized transmission images. These measured properties included the Sauter mean diameter (SMD) averaged over the entire spray or over a given cross-section. In addition, the images yielded other spray parameters such as tip penetration, cone angle, and injection duration.
Technical Paper

Improvements in 3-D Modeling of Diesel Engine Intake Flow and Combustion

A three-dimensional computer code (KIVA) is being modified to include state-of-the-art submodels for diesel engine flow and combustion: spray atomization, drop breakup/coalescence, multi-component fuel vaporization, spray/wall interaction, ignition and combustion, wall heat transfer, unburned HC and NOx formation, soot and radiation and the intake flow process. Improved and/or new submodels which have been completed are: wall heat transfer with unsteadiness and compressibility, laminar-turbulent characteristic time combustion with unburned HC and Zeldo'vich NOx, and spray/wall impingement with rebounding and sliding drops.
Technical Paper

Optimization of Heavy-Duty Diesel Engine Operating Parameters Using A Response Surface Method

A study of statistical optimization of engine operating parameters was conducted. The objective of the study was to develop a strategy to efficiently optimize operating parameters of diesel engines with multiple injection and EGR capabilities. Previous studies have indicated that multiple injections with EGR can provide substantial simultaneous reductions in emissions of particulate and NOx from heavy-duty diesel engines, but careful optimization of the operating parameters is necessary in order to receive the full benefit of these combustion control techniques. The goal of the present study was to optimize the control parameters to reduce emissions and brake specific fuel consumption. An instrumented single-cylinder heavy-duty diesel engine was used with a prototype mechanically actuated (cam driven) fuel injection system.
Technical Paper

Validation of a Sparse Analytical Jacobian Chemistry Solver for Heavy-Duty Diesel Engine Simulations with Comprehensive Reaction Mechanisms

The paper presents the development of a novel approach to the solution of detailed chemistry in internal combustion engine simulations, which relies on the analytical computation of the ordinary differential equations (ODE) system Jacobian matrix in sparse form. Arbitrary reaction behaviors in either Arrhenius, third-body or fall-off formulations can be considered, and thermodynamic gas-phase mixture properties are evaluated according to the well-established 7-coefficient JANAF polynomial form. The current work presents a full validation of the new chemistry solver when coupled to the KIVA-4 code, through modeling of a single cylinder Caterpillar 3401 heavy-duty engine, running in two-stage combustion mode.