Search Results

Advanced Vehicle Technologies (AVT), a Ballarat Australia based company, has developed the World's first diesel to 100% LPG conversion for heavy haul trucks. There is no diesel required or utilized on the trucks. The engine is converted with minimal changes into a spark ignition engine with equivalent power and torque of the diesel. The patented technology is now deployed in 2 Mercedes Actros trucks. The power output in engine dynamometer testing exceeds that of the diesel (in excess of 370 kW power and 2700 Nm torque). In on-road application the power curve is matched to the diesel specifications to avoid potential downstream power-train stress. Testing at the Department of Transport Energy & Infrastructure, Regency Park, SA have shown the Euro 3 truck converted to LPG is between Euro 4 and Euro 5 NOx levels, CO2 levels 10% better than diesel on DT80 test and about even with diesel on CUEDC tests.

This paper is a summary of the aerodynamic development of the 1988 Chevrolet and GMC pickup truck. Comprehensive drag reduction work was performed with clay models from the original concept through the detailed full-scale model. In addition, the aerodynamic development included wind rush noise reduction, optimization of engine cooling air flow, and body surface pressures for HVAC performance.

Thermal Management Systems Symposium industry discusses latest regulatory impacts, applications to reduce engine emissions, conserve energy, reduce noise, improve the cabin environment, increase overall vehicle performance passenger, commercial vehicle industry.

J I Case Company has produced four-wheel-drive agricultural tractors since 1964. In 1984 however, the flagship of the Case fleet changed hands. Rising labor costs and larger farming operations spearheaded the need for a more efficient larger tractor. January 1984 marked the introduction of the largest four-wheel-drive tractor in the history of Case, the 4994, a 400-gross engine horsepower tractor, Figure 1. Sheer horsepower alone however, would not meet the requirements of today's farming operations. Case Engineering realized that tomorrows tractors must have sufficient power to handle the wide variety of attachments available. They also realized that along with the unmatched power must come precise control of the attachment. These advancements in farming have required improvements to the tractor hydraulic system. This paper describes the hydraulic system of the 4994, Case's new flagship.

Over the past several years the Institute of Electrical and Electronic Engineers (IEEE) Standards Association has developed standards for the 5.9 GHz Dedicated Short Range Communications protocols, also known as Wireless Access in Vehicular Environments. These standards consist of IEEE 1609 as well as an amendment to the IEEE 802.11 standard or 802.11p. The 1609 standards were published for Trial Use and these as well as the 802.11p draft have been implemented in a variety of test beds to provide lessons learned and feedback into the standards working groups. Based on ongoing testing, the protocols display a strong capability to address the requirements of crash avoidance and transportation mobility applications. The corresponding test results provide information necessary to update the standards after the first trial phase as industry moves toward commercial implementations.

The story of Power Farming is the great saga of our times. It is a story of free enterprise, perseverance and endurance of the individual, of vision, idealism and cooperation among men, of the lightening of human toil and the release of millions of workers from farms to feed the ever hungry industrial revolution. By no means least, it is the story of producing food necessary to win two global wars, keep our allies alive and millions of the defeated enemy from starvation. FOREWARD By 1915, the Steam Traction Engine had attained its highest development. It was the forerunner, rather than the predecessor, of the farm tractor. The former was the instrument of expansion; the latter, the instrument of progress. The invention of the tractor, following by only sixteen years Otto's practical embodiment application of the Beau de Rochas power cycle to a heat engine, marked the advent of a new order - - the age of Power Farming.

This paper describes a building block approach for understanding the past, present and future four wheel drive systems. The emphasis will be on light trucks and sport utility vehicles. It will describe the advantages of four wheel drive and how it improves performance and safety. The building block approach is a tool for categorizing the basic systems in the market. Systems are separated into main component areas and are rated for the effect they have on the overall performance and safety. This paper can be used as a means for understanding a very complex 4x4 market.

Various drag reduction strategies have been applied to a full size production pickup truck to evaluate their effectiveness by using Computational Fluid Dynamics (CFD). The drag reduction devices evaluated in this study were placed at the rear end of the truck bed and the tailgate. Three types of devices were evaluated: (1) boat tail-like extended plates attached to the tailgate; (2) mid-plate attached to the mid-section of the tailgate and; (3) flat plates partially covering the truck bed. The effect of drag reduction by various combinations of these three devices are presented in this paper. Twenty-four configurations were evaluated in the study with the best achievable drag reduction of around 21 counts (ΔCd = 0.021). A detailed breakdown of the pressure differentials at the base of the truck is provided in order to understand the flow mechanism for the drag reductions.

A cartridge type pivotal pin and bushing joint has been patented and is being tested and refined both in the laboratory and on construction machinery. It features “dry lubricated” (Teflon) bearings which are assembled and sealed prior to installation. It is suitable for heavy unit loads and use under severe wear conditions, such as in crawler track chains and loader bucket pivotal pin joints. A brief history of U. S. manufactured track pin joints is included to show the progress in extending the service life of these devices.

In the truck industry there is a continuous demand to increase the efficiency and to decrease the emissions. To acknowledge both these issues a waste heat recovery system (WHR) is combined with a partially premixed combustion (PPC) engine to deliver an efficient engine system. Over the past decades numerous attempts to increase the thermal efficiency of the diesel engine has been made. One such attempt is the PPC concept that has demonstrated potential for substantially increased thermal efficiency combined with much reduced emission levels. So far most work on increasing engine efficiency has been focused on improving the thermal efficiency of the engine while WHR, which has an excellent potential for another 1-5 % fuel consumption reduction, has not been researched that much yet. In this paper a WHR system using a Rankine cycle has been developed in a modeling environment using IPSEpro.

This paper discusses controller development for an active, off-road vehicle suspension system. A brief review of electronic filters and their characteristics is used to provide insight on the difficulties of designing a control algorithm for negotiating hilly and rough terrain at higher speeds. Two controller designs are presented. One was designed by pole placement and causes the suspension response to approximate a Type 1 Chebychev filter. The other was designed using constrained optimization. A comparison and discussion of simulation results leads to the conclusion that the suspension should be adaptively or predictively controlled for arbitrary terrain and velocity conditions.

A Decision Network is an explicit model of the Thinking Breakdown Structure of any complex scientific, engineering, or societal challenge. Each node in the Decision Network represents a fundamental question that must be answered, i.e. a choice that demands a solution. A Decision Network provides an integrated Decision Management framework for any Systems Engineering effort that links business, technology and design choices. Effective Decision Management is the key to Systems Engineering success. This paper will provide an overview of a decision-centric approach to Systems Engineering built around Decision Networks. Lessons learned through the use of Decision Networks in other industries will be extrapolated for use in vehicle Systems Engineering.

The need for a foreshortened product development lead time has become a necessity, in today's economy, to the efficient manufacturing of off-highway mining trucks. This paper reviews the approach taken by one noted truck manufacturer. By utilizing finite element analysis, plastic scale modeling techniques, and a comprehensive full scale test facility, the development lead time of the WABCO 100 Ton HAULPAK* was reduced to 60% of that normally required for the development of a new product from conceptual layout to production release.

Heavy commercial vehicle axle shafts are designed for torsion load. Typically, axle shaft fracture mode during the test is torsional in nature through either shaft body diameter or spline end. However, some of the field return axles shows fracture mode on axle shaft flange. This fracture mode does not resemble with a typical lab test torsional fracture. Metallurgical investigation report indicated that the fracture mode is bending in nature. This paper thus focuses on detail study of change in boundary condition and load transfer path under abusive vertical bending load on axle. A detail finite element analysis is performed to understand stress state change in axle shaft under this condition. A fracture hypothesis is proposed based on observations of finite element analysis results. A detail case study is presented depicting correlation of proposed hypothesis with physical fracture mode.

Adjuster rings are used in commercial vehicle axle assembly to preload differential bearings and provide support in the axial direction. Adjuster along with the carrier and bearing cap combined to form a threaded joint. Adjuster with external threads engages with internal threads formed in carrier and bearing cap. Preload in differential assembly maintains the system rigidity and helps to maintain an optimized hypoid gear engagement. An adequate preload is important to achieve a desirable bearing life. Reduction in thread engagement at adjuster joint fully or partially will cause a reduction in preload and can lead to gear misalignment. This can cause severe durability concerns. In some cases, it is observed that under vehicle operating loads adjuster ring is backed off from its assembled condition by bending the split pin (split pin is, positive lock, used to maintain adjuster position) and adjuster threads were stripped off.

The need to reduce the injury to pedestrians that are run over or pinned beneath a bus is an ongoing concern for transit authorities and other operators. Occasionally, a pedestrian will be run over by the right rear wheel while exiting the rear door. This accident occurs in various scenarios such as when people exit the bus and become entangled in the door grab bars, or when they fall between the curb and the bus while it approaches or departs. With all scenarios, the S-1 Gard acts similar to a cow catcher, pushing the fallen pedestrian out and away from the rear tire. This paper will: outline various incident scenarios, evaluate the S-1 Gard's performance in a city environment, review installation of the guard as well as its maintenance requirements. The purpose of this paper is to bring to the attention of transit authorities and shuttle operators the overall value of this device.

A method has been developed which allows prediction of the field performance of structural components based on prototype vehicle test procedures and results. Component designs can then be optimized by selecting prototype durability test objectives which more accurately reflect actual field usage. This procedure, which is based on fatigue damage calculations from component strain histories, has been successfully applied to non-safety related body, frame and suspension structural components of light trucks and vans.

Pinion bearing loads of a heavy duty rear truck axle were determined by Finite Element Method Analysis (FEM). The results were compared with measured loads. This report describes the method used to measure bearing loads, the FEM model used, and the comparison of the results.

The rollover threshold for a partially filled tanker truck carrying fluid cargo is of great importance due to the catastrophic nature of accidents involving such vehicles, particularly when payloads are toxic and flammable. In this paper, a method for determining the threshold of rollover stability of a specific tanker truck is presented using finite element analysis methods. This approach allows the consideration of many variables which had not been fully incorporated in past models, including nonlinear spring behavior and tank flexibility. The program uses simple mechanical pendulums to simulate the fluid sloshing affects, beam elements to match the torsional and bending stiffness of the tank, and spring damper elements to simulate the suspension. The finite element model of the tanker truck has been validated using data taken by the U.S. Army Aberdeen Test Center (ATC) on a M916A1 tractor/ Etnyre model 60PRS 6000 gallon trailer combination.