Search Results

The demand for improved fuel economy in both cars and trucks has emphasized the need for lighter weight components. The application of high strength steel to wheels, both rim and disc, represents a significant opportunity for the automotive industry. This paper discusses the Ranger HSLA wheel program that achieved a 9.7 lbs. per vehicle weight savings relative to a plain carbon steel wheel of the same design. It describes the Ranger wheel specifications, the material selection, the metallurgical considerations of applying HSLA to wheels, and HSLA arc and flash butt welding. The Ranger wheel design and the development of the manufacturing process is discussed, including design modifications to accommodate the lighter gage. The results demonstrate that wheels can be successfully manufactured from low sulfur 60XK HSLA steel in a conventional high volume process (stamped disc and rolled rim) to meet all wheel performance requirements and achieve a significant weight reduction.

The in-cylinder direct injection of fuels can be a further step towards cleaner and more efficient internal combustion engines. However, the injector design and its characterization, both experimental and from numerical simulation require accurate diagnostics and efficient models. This work aims to simulate the complex behavior of the gaseous and liquid jets through an outwardly opening injector characterized by optical diagnostics using a one-dimensional model without using three dimensional models. The behavior of the jet from an outwardly opening injector changes according to the type of fuel. In the case of the gas, the experimental investigations put in evidence three main jet regions: 1) near-field region where the jet shows a complex gas-dynamic structure; 2) transition region characterized by intense mixing; 3) far-field region characterized by a fully developed subsonic turbulent jet.

This paper describes the after-treatment technology that could be used to meet a future BS-VII standard, considering close-coupled SCR (cc-SCR) to help start NOx conversion earlier. Both active (Cu/Fe-SCR based) and passive (V-SCR based) systems have the potential to meet emission limits. V-SCR may be considered in the rear position because V-SCR shows a fast response with very low N2O formation. Next-gen V-SCR technology shows significantly improved performance and durability closer to Cu-SCR. The steady-state NOx conversions over Next-Gen V-SCR were better than BS-VI V-SCR in both fresh and aged-580°C/100h conditions. High durability was also observed after engine aging of 1000h (WHTC + high load). Another big challenge in BS VII could be the PN10 requirement. With enhanced filtration coating (EFC) technology, PN emissions drop drastically in comparison to Euro VI reference without EFC to meet a future BS VII.

The new 5480 Reach Truck, designed at Dynamic Industries, introduces a movable frame between the main frame and the telescopic boom. The use of this movable frame allows the usually fixed boom pivot to be elevated for greater lifting heights with smaller boom sections. By combining the motions of the boom and the movable frame, horizontal motion at the boom tip is possible without moving the truck. With the movable frame, the total machine height and length can be reduced for a given lifting goal. Another advantage of the movable frame is the ability to reach further below grade than is now possible in the industry. The 5480 Reach Truck has a maximum lift of 54 feet (16.5 meters) and can reach 24 feet (7.3 meters) below-grade.

A pin and disc machine has been modified for the evaluation of silver-steel lubrication characteristics of railroad diesel oils. Use of silver pins on polished steel discs at selected loads and rubbing speeds allows good correlation with known engine behavior. In comparison with wear and friction data obtained by the four ball method, this pin and disc test gives better correlation with engine tests than the Modified Four Ball Test.

A unique shuttle bus is being constructed by Minicars, Inc., and Walter Vetter Karosserie-werk for Denver’s Transitway/Mall. The bus is designed for frequent stop, low speed service in a downtown pedestrian environment. It features a very low floor and multiple wide doors for rapid passenger boarding and deboarding. Two versions will be supplied for comparative evalation, a low noise diesel configuration and a battery-electric configuration. Either version can subsequently be converted to the alternative propulsion system.

Engine mounts are an integral part of the vehicle that helps in reducing the vibrations generated from the engine. Engine mounts require a simple yet complicated amalgamation of two very different materials, steel and rubber. Proper adhesion between the two is required to prevent any part failure. Therefore, it becomes important that a comprehensive study is done to understand the mating phenomenon of both. A good linking between rubber and metal substrate is governed by surface pretreatment. Various methodologies such as mechanical and chemical are adopted for the same. This paper aims to present a comparative study as to which surface pretreatment has an edge over other techniques in terms of separation force required to break the bonding between the two parts. The study also presents a cost comparison between the techniques so that the best possible technique can be put to use in the commercial vehicle industry.

This paper describes the results of a series of fatigue studies relating the lives of several weld geometries. Rotating beam and axially loaded specimens were used. A comparison between steel and plastic (polyvinylchloride scale models is made. Using plastic scale models of welded structures for fatigue life determination is the ultimate goal of this work.

“Today, wearing parts are regularly subjected to abnormal loading conditions. They must be able to accept these conditions without failure. In continuous operations, unscheduled downtime greatly increases maintenance costs, not to mention the cost of lost production. White iron castings offer premium abrasion resistance for many of these applications, but are often not used due to the possibility of brittle failure and the difficulty of mechanical attachment. This paper discusses the properties and applications of a composite of martensitic white iron and mild steel. This laminate will accept medium to high impact without loss of service failure, and can be installed by mechanical means or with welded attachment.”

The classical methods of deflection analysis are finding more application to complex automotive chassis frame structures. Much too time consuming for manual application, they are now coming into more widespread use with the aid of high-speed computers. This paper describes a computerized deflection analysis for complete truck frames under the cases of torsion and flexure. The rapid, accurate analysis permits investigation of more design problems resulting in the eventual production of more efficient frame structures.

Predicting fatigue performance in concentrated contacts under thin film (or mixed) lubrication conditions has historically involved various empirical approaches. Typically a lubrication parameter is used in an experimentally derived equation to predict the expected rolling contact performance. However, this model doesn't explain the performance improvements. Enhanced finish bearings have exhibited longer life than standard finish bearings, especially when bearings are operated with thin EHL film. In this paper, the contact surfaces of test bearings were analyzed by using a micro-macro contact model in which the macro-contact was elastic contact, and the micro-contact was elastic-plastic contact. The interior subsurface stress maps were calculated from the real contact surfaces, which included the effects of roughnesses, waviness, and profiles.

A rear-steering control method for a four-wheel steering truck has been developed. The purpose of this investigation is to develop a control method to minimize the turning radius without the excursion of the vehicle rear end toward the outside of the turn. The basic control concept is to steer the rear wheels so that the vehicle rear end follows the path of the front end. The control method was applied to an experimental medium-duty truck with four-wheel steering system. The simulation and vehicle test results showed the control method to be effective in minimizing the turning radius without causing the excursion of the vehicle rear end toward the outside in short turns.

Current trends in environmental and emissions regulations are driving changes in new engine systems, and increasing the need for more effectively sealed joints in exhaust systems. At the high temperatures in these exhaust systems it is difficult for traditional gaskets to provide an effective seal, as they degrade at high operating temperatures. This paper introduces a coating that has both excellent temperature stability and good compliance, thus forming an excellent sealing enhancement for metallic layers in exhaust system gaskets. Temperature stability data is presented along with sealing data, which illustrate the superior performance of this material compared to current systems.

A software tool has been developed to aid designers and process engineers in the development and improvement of heat treat processes. This tool, DANTE™, combines metallurgical phase transformation models with mass diffusion, thermal and mechanical models to simulate the heating, carburization, quenching and tempering of steel parts. The technology behind the DANTE software and some applications are presented in this paper.

Paper describes analysis of the design process of modern automotive LPG and CNG containers. Over decade experience in the field of both computer based analysis as well as in the real conditions testing has been collected and presented in the paper. Authors present the potentials of modern FEM methodologies in the optimization and production of lightweight steel containers. It has been proved that the most sophisticated numerical analysis have to be followed by the construction verification, particularly considering direct exposure to fire. Bonfire test have become obligatory for both liquid and compressed gases containers. Properly chosen fire protection system, together with the adequate level of quality of materials applied for its production together with proper directing of the gas flowing out from safety devices are the essential factors defining gas containers fire safety.

A direct method is developed for designing a vehicle fuel filler door with torsional spring. The design parameters include the door's geometrical parameters and spring dimensions. The design requirements are based on the finger force curve during closing and opening, and the bending stress in the spring. An example is included to demonstrate the effectiveness of the new method.

We propose a novel dual-fuel combustion model for simulating heavy-duty engines with the G-Equation. Dual-Fuel combustion strategies in such engines features direct injection of a high-reactivity fuel into a lean, premixed chamber which has a high resistance to autoignition. Distinct combustion modes are present: the DI fuel auto-ignites following chemical ignition delay after spray vaporization and mixing; a reactive front is formed on its surroundings; it develops into a well-structured turbulent flame, which propagates within the premixed charge. Either direct chemistry or the flame-propagation approach (G- Equation), taken alone, do not produce accurate results. The proposed Dual-Fuel model decides what regions of the combustion chamber should be simulated with either approach, according to the local flame state; and acts as a “kernel” model for the G- Equation model. Direct chemistry is run in the regions where a premixed front is not present.

In the near future, GM will introduce a new product to the marketplace. The vehicle is a full-size, four-door utility vehicle based on its current C/K full-size truck product line. This new vehicle is smaller than the current Suburban and does not provide room for a third seat. It is expected that this utility will supplement the small truck four-door utility and create a new market niche with its unique size and features. The process used to design, develop and validate the new product in an aggressive 93-week time frame, is the subject of this paper.

The need to reduce the injury to pedestrians that are run over or pinned beneath a bus is an ongoing concern for transit authorities and other operators. Occasionally, a pedestrian will be run over by the right rear wheel while exiting the rear door. This accident occurs in various scenarios such as when people exit the bus and become entangled in the door grab bars, or when they fall between the curb and the bus while it approaches or departs. With all scenarios, the S-1 Gard acts similar to a cow catcher, pushing the fallen pedestrian out and away from the rear tire. This paper will: outline various incident scenarios, evaluate the S-1 Gard's performance in a city environment, review installation of the guard as well as its maintenance requirements. The purpose of this paper is to bring to the attention of transit authorities and shuttle operators the overall value of this device.

A method has been developed which allows prediction of the field performance of structural components based on prototype vehicle test procedures and results. Component designs can then be optimized by selecting prototype durability test objectives which more accurately reflect actual field usage. This procedure, which is based on fatigue damage calculations from component strain histories, has been successfully applied to non-safety related body, frame and suspension structural components of light trucks and vans.