Refine Your Search

Date

Date

Topic

Topic

Engine components AE-5B Aircraft and Engine Fuel and Lubricant Sys Components Combustion chambers Thermodynamics

Search Results

Viewing 1 to 20 of 24
12Next >Last >>
Sort by title
Standard

AIRCRAFT FUEL PUMP CAVITATION ENDURANCE TEST
1957-11-15
HISTORICAL
ARP492
This procedure is intended to apply to any aircraft fuel pump which supplies liquid hydrocarbon fuel either directly to an aircraft engine or to another pump mounted on an aircraft engine, except that it is not intended to apply to a fuel pump mounted in a fuel tank.
Standard

AIRCRAFT TURBINE ENGINE FUEL SYSTEM COMPONENT ENDURANCE TEST PROCEDURE (ROOM TEMPERATURE CONTAMINATED FUEL)
2007-12-04
HISTORICAL
MAP749B
This recommended practice describes a method for conducting room temperature, contaminated fuel, endurance testing when the applicable specification requires nonrecirculation of the contaminants. The objective of the test is to determine the resistance of engine fuel system components to wear or damage caused by contaminated fuel operation. It is not intended as a test for verification of the component’s filter life. ARP1827 is recommended for filter evaluation.
Standard

Aircraft Engine Fuel Feed and Transfer Component Pressure Definitions
2013-02-05
HISTORICAL
AIR1749
The information in this document is limited to aircraft engine fuel feed, refueling, and transfer components (reference 2.1). It is assumed that isothermal, liquid fluid conditions exist, herein referred to as fuel. Where a unit of measure is suffixed, this is intended to show a generally associated unit for illustration only and is not an exclusive endorsement of this particular term. Where applicable and allowable it is understood that a referee fluid may be substituted for fuel.
Standard

Aircraft Engine Fuel Pump Cavitation Endurance Test
2022-04-28
WIP
ARP492D
This SAE Aerospace Recommended Practice (ARP) defines procedures for testing aircraft engine fuel pumps for the purpose of determining their resistance to deterioration, during steady state endurance test, while receiving MIL-T-5624 Grade JP-4 fuel as a homogenous mixture of gas and liquid expressed as a ratio of vapor volume to liquid volume (V/L).

If any of the above conditions do not apply, refer to Section 2.

The procedure recommended herein is based on experience gathered by a number of laboratories conducting component qualification tests to MIL-E-5009, currently MIL-E-5007. It is intended to produce a uniform reproducible steady state test condition for fuel pump cavitation testing as required by various military engine specifications.

This test is not intended to establish altitude or climb rate, starting, or other transient performance of the article tested.

Standard

Aircraft Engine Fuel Pump Cavitation Endurance Test
2021-03-09
CURRENT
ARP492C
This SAE Aerospace Recommended Practice (ARP) defines procedures for testing aircraft engine fuel pumps for the purpose of determining their resistance to deterioration, during steady state endurance test, while receiving MIL-T-5624 Grade JP-4 fuel as a homogenous mixture of gas and liquid expressed as a ratio of vapor volume to liquid volume (V/L). If any of the above conditions do not apply, refer to Section 2.
Standard

Aircraft Turbine Engine Fuel System Component Endurance Test Procedure (Room Temperature Contaminated Fuel)
2022-05-02
CURRENT
MAP749C
This SAE Aerospace Recommended Practice describes a method for conducting room temperature, contaminated fuel, endurance testing when the applicable specification requires nonrecirculation of the contaminants. The objective of the test is to determine the resistance of engine fuel system components to wear or damage caused by contaminated fuel operation. It is not intended as a test for verification of the component's filter performance and service life. ARP1827 is recommended for filter performance evaluation.
Standard

Aircraft/Engine Fuel Pump Net Positive Suction Pressure Performance Test and Evaluation
2020-04-29
CURRENT
ARP4024
This procedure applies to engine or airframe-mounted fuel pumps. The procedure recommends single-pass operation to minimize changes in fuel properties affecting NPSP capability. An optional method using a recirculation system is also included and may be specified at the discretion of the equipment specification. This procedure defines the recommended test setup, test procedure, data acquisition, and data presentation.
Standard

Aircraft/Engine Fuel Pump Two Phase (Slugging Flow) Inlet Performance Test and Evaluation
2020-04-29
CURRENT
ARP4028
This procedure is intended to apply to all engine or airframe mounted fuel pumps and controls when required by the applicable specification. The procedure recommends a recirculation system similar to ARP492 to control the fuel properties affecting the fluid and its ability to "release" fuel vapors and dissolved air and have these "re-entrained or dissolved" during the fluid recovery process back to the tank and the original starting conditions.
Standard

Contaminants for Aircraft Turbine Engine Fuel System Component Testing
2002-04-19
HISTORICAL
AIR4246B
This document discusses descriptions of fluid contamination products. These contaminants are used for design evaluation and formal component qualification/certification testing. Such tests are routinely performed on candidate aircraft engine fuel and pneumatic system components. Typical of these components are fuel pumps, fuel filters, fuel controls, pressurizing valves, flow dividers, selector valves, and combustor nozzles. The purpose of this document is to recommend standard descriptions to be used by specification writers.
Standard

Contaminants for Aircraft Turbine Engine Fuel System Component Testing
2010-08-05
HISTORICAL
AIR4246C
This document discusses descriptions of fluid contamination products. These contaminants are used for design evaluation and formal component qualification/certification testing. Such tests are routinely performed on candidate aircraft engine fuel and pneumatic system components. Typical of these components are fuel pumps, fuel filters, fuel controls, pressurizing valves, flow dividers, selector valves, and combustor nozzles. The purpose of this document is to recommend standard descriptions to be used by specification writers.
Standard

Fire Testing of Fluid Handling Components for Aircraft Engines and Aircraft Engine Installations
2007-02-15
CURRENT
AS4273A
This document establishes requirements, test procedures, and acceptance criteria for the fire testing of fluid handling components and materials used in aircraft fluid systems. It is applicable to fluid handling components other than those prescribed by AS1055 (e.g., hoses, tube assemblies, coils, and fittings). It also is applicable to materials, wiring, and components such as reservoirs, valves, gearboxes, pumps, filter assemblies, accumulators, fluid-cooled electrical/electronic components, in-flight fluid system instrumentation, hydromechanical controls, actuators, heat exchangers, and manifolds. These components may be used in fuel, lubrication, hydraulic, or pneumatic systems.
Standard

Measuring Aircraft Gas Turbine Engine Fine Fuel Filter Element Performance
2021-07-23
CURRENT
ARP1827D
This SAE Aerospace Recommended Practice (ARP) delineates two complementary filter element performance parameters: (1) dirt capacity, and (2) filtration efficiency, and corresponding test procedures. It is intended for non-cleanable (disposable), fine fuel filter elements, rated at 25 µm(c) or finer, used in aviation gas turbine engine fuel systems.
12Next >Last >>
X