Search Results

Standard

BEADED TUBE HOSE FITTINGS

1993-06-01

HISTORICAL

J1231_199306

This SAE Standard covers complete general and dimensional specifications for beaded tube hose fittings. These fittings are intended for general applications in low-pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figures 1 to 3 and Table 1 are intended for use with low-pressure hose and shall be retained by hose clamps as specified in SAE J1508.

Standard

Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers

2006-03-27

HISTORICAL

J2631_200603

This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.

Standard

Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers

2011-10-25

CURRENT

J2631_201110

This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.

Standard

Formed Tube Ends for Hose Connections and Hose Fittings

1998-07-01

HISTORICAL

J1231_199807

This SAE standard provides general and dimensional specifications for formed tube ends and hose fittings. These connections are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figures 2 and 3 are intended to be retained by hose clamps as specified in SAE J1508. It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.

Standard

Formed Tube Ends for Hose Connections and Hose Fittings

2011-05-16

HISTORICAL

J1231_201105

This SAE Standard provides general and dimensional specifications for formed tube ends and hose fittings. These connections are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figures 2 and 3 are intended to be retained by hose clamps as specified in SAE J1508. It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.

Standard

Formed Tube Ends for Hose Connections and Hose Fittings

2016-08-02

HISTORICAL

J1231_201608

This SAE Standard provides general and dimensional specifications for formed tube ends and hose fittings. These connections are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figures 2 and 3 are intended to be retained by hose clamps as specified in SAE J1508. It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.

Standard

HOSE AND HOSE ASSEMBLIES FOR MARINE APPLICATIONS

1992-05-01

HISTORICAL

J1942_199205

SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 1991,1 as the official document for nonmetallic flexible hose assemblies for marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. A Hose Assemblies Listing of the products which can be used for the applications described in Table 1 is available from SAE, Publication Number EA-1942.

Standard

HOSE AND HOSE ASSEMBLIES FOR MARINE APPLICATIONS

1989-03-01

HISTORICAL

J1942_198903

This standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this standard establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation and maintenance of hose and hose assemblies.

Standard

HOSE AND HOSE ASSEMBLIES FOR MARINE APPLICATIONS

1995-05-01

HISTORICAL

J1942_199505

SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 19911, as the official document for nonmetallic flexible hose assemblies for marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. SAE J1942/1 is a Hose Assemblies Listing of the products which have been certified for use in the applications described in Table 1. This document is updated each year and is available from SAE as a single copy publication.

Standard

HOSE AND HOSE ASSEMBLIES FOR MARINE APPLICATIONS

1993-06-01

HISTORICAL

J1942_199306

SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 19911, as the official document for nonmetallic flexible hose assemblies for marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. A Hose Assemblies Listing of the products which can be used for the applications described in Table 1 is available from SAE as SAE J1942/1.

Standard

Hose and Hose Assemblies for Marine Applications

2019-03-22

CURRENT

J1942_201903

SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 19911, as the official document for nonmetallic flexible hose assemblies for commercial marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems aboard commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. Refer to SAE J1527 for hose to convey gasoline or diesel fuel aboard small craft, including pleasure craft and related small commercial craft regulated directly or by reference under 33 CFR 183 Subpart J, and boats and yachts meeting American Boat and Yacht Council standards.

Standard

Hose and Hose Assemblies for Marine Applications

2014-06-06

HISTORICAL

J1942_201406

SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 19911, as the official document for nonmetallic flexible hose assemblies for commercial marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. Refer to SAE J1527 Marine Fuel Hose for hose to convey gasoline or diesel fuel aboard small craft, including pleasure craft and related small commercial craft regulated directly or by reference under 33 CFR 183 Subpart J, and boats and yachts meeting American Boat and Yacht Council standards.

Standard

Hydraulic Hose Fittings

2011-10-25

HISTORICAL

J516_201110

This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 15 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user. Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies. THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J516 FITTINGS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES.

Standard

Hydraulic Hose Fittings

2016-04-06

HISTORICAL

J516_201604

This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 15 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user. Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies. THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J516 FITTINGS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES.

Standard

Hydraulic Hose Fittings

2019-03-20

HISTORICAL

J516_201903

This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 17 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user. Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies. The rated working pressure of a hose assembly comprising SAE J516 fittings and SAE J517 hoses shall not exceed the lower of the two working pressure rated values.

Standard

TEST AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1993-06-01

HISTORICAL

J343_199306

This SAE Standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1990-05-01

HISTORICAL

J343_199005

This SAE Standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1989-05-01

HISTORICAL

J343_198905

This standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R Series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1991-04-01

HISTORICAL

J343_199104

This SAE Standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1968-06-01

HISTORICAL

J343_196806

This standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R Series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.