Refine Your Search

Search Results

Standard

Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Xenon-Arc Apparatus

2015-12-14
WIP
J2412
This test method specifies the operating procedures for a controlled irradiance, xenon arc apparatus used for the accelerated exposure of various automotive interior trim components. Test duration as well as any exceptions to the specimen preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers. Any deviation to this test method, such as filter combinations, is to be agreed upon by contractual parties.
Standard

Design Guidelines for Fiberboard Materials

2019-07-10
WIP
J1774
This document provides information on the various fiberboard products, which are available for automotive application. It is intended to give engineers and designers a better understanding of product usage, characteristics, properties and industry terminology. The following sections cover these topics: 2. General Product Information 3. Design Characteristics 4. Physical/Mechanical Properties 5. Fiberboard Definitions In sections 2, 3 and 4 the fiberboard products are categorized. These sections give an overview of product types, with general information about characteristics and properties. In cases where product categories encompass more than one material or material grade, ranges were established to cover all of the products in that category. The individual companies that supply fiberboard products should be consulted for specific information about a particular product or application.
Standard

Determination of the Fogging Characteristics of Interior Automotive Materials

2013-12-06
WIP
J1756
1.1 This recommended practice describes two methods for determining the tendency of interior materials used in automobiles and other vehicles to (a) produce a light scattering deposit (fog) on a glass surface, or (b) produce a measurable deposit (mass) on aluminum foil. 1.2 This document is applicable to the measurement of a fog condensate on glass or aluminum foil surfaces within the limits of the test conditions. 1.3 It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to its use.
Standard

Felts - Wool and Part Wool

2012-08-24
CURRENT
J314_201208
This SAE Standard identifies chemical/mechanical properties, thickness, width, mass, and other requirements recommended for felts (refer to Tables 1 and 2). It was developed with the cooperation of the Standardization Committee of the Felt Association, Inc., and in accordance with the ASTM tests indicated in the document. The commercial trade designations of the more commonly used grades of automotive felts are given along with complete specifications and tolerances for thickness, mass, wool content, chemical and physical requirements, color, and width. General information, recommended uses, etc., are published in Appendix A as a guide in the selection of felts for particular uses, but the requirements for each application should be taken into consideration in making final selections.
Standard

Fiberboard Test Procedure

2016-03-29
WIP
J315
This SAE Standard provides test methods for determining the critical characteristics of basic or finished fiberboard products. Where applicable, methods of test developed by SAE and ASTM have been referenced.
Standard

Flammability of Polymeric Interior Materials - Horizontal Test Method

2019-06-10
WIP
J369
This SAE Standard pertains to automotive vehicles and off-road, self-propelled work machines used in construction, general purpose industrial, agriculture, forestry, and specialized mining machinery. This standard does not address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this document to establish safety and health practices and determine the applicability of regulatory limitations prior to use. Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed when conducting this test.
Standard

Instrumental Color Difference Measurement for Exterior Finishes, Textiles and Colored Trim

2014-10-27
CURRENT
J1545_201410
The practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials that are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film.
Standard

Instrumental Color Difference Measurement for Exterior Finishes, Textiles and Colored Trim

2005-07-25
HISTORICAL
J1545_200507
The practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials that are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film.
Standard

Instrumental Color Difference Measurement for Exterior Finishes, Textiles and Colored Trim

2019-06-05
WIP
J1545
The practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials that are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film.
Standard

Instrumental Color Difference Measurement for Exterior Finishes, Textiles, and Colored Trim

1986-06-01
HISTORICAL
J1545_198606
The intent of this practice is to precisely specify procedures for instrumental color difference measurement of colored parts or colored materials incorporated in the manufacture of vehicles. The recommended practice provides a consistent engineering practice for determination of color difference, for numerical communication of color difference, and for determination of acceptance or rejection compared to numerical tolerances. The practice is intended to be used as a specification and means of communication for color part acceptance in a buyer-seller agreement. The practice applies to parts and materials used in vehicles manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials which are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, and exterior hard trim, and exterior film.
Standard

Instrumental Color Difference Measurements for Colorfastness of Automotive Interior Trim Materials

2019-06-05
WIP
J1767
The practice described applies to textile and flexible plastic parts and materials used in automotive vehicles. Special care should be taken when high pile carpet samples are being evaluated. The intent of this SAE Recommended Practice is to specify procedures for the instrumental measurement of color differences brought about by the exposure of textile and flexible plastic automotive parts to various colorfastness tests. It may be used for the specification of limits of color differences which may be tolerated in a specific test.
Standard

Method of Testing Resistance to Crocking of Organic Trim Materials

2012-08-24
CURRENT
J861_201208
This test can be used to determine the resistance to crocking (color rub-off) of organic trim materials such as fabrics, vinyl coated fabrics, leather, coated fiberboard and carpet. This method is similar to AATCC Method 8 –Colorfastness to Crocking.
Standard

Seam Damage Test Procedure

2014-05-20
CURRENT
J1531_201405
This procedure is used to determine seam strength and seam fatigue of automotive textiles, vinyl coated fabrics and related soft trim materials.
Standard

Seam Damage Test Procedure

2008-05-02
HISTORICAL
J1531_200805
This procedure is used to determine seam strength and seam fatigue of automotive textiles, vinyl coated fabrics and related soft trim materials.
Standard

Standard Specification for Allowable Defects in Rolled Goods for Interior Trim

2014-01-02
WIP
J3064
1.1 This specification is written for rolled goods used for trim sets for automotive seats. Face materials are textiles and plastic goods. This specification covers material rolled goods with and without foam or backing adhered to the face material 1.2 Units shall be SI. 1.3 This standard does not purport to address all of the safety concerns, is any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
X