Refine Your Search

Search Results

Standard

Felts - Wool and Part Wool

1976-01-01
HISTORICAL
J314B_197601
This SAE Standard identifies chemical/mechanical properties, thickness, width, mass, and other requirements recommended for felts (refer to Tables 1 and 2). It was developed with the cooperation of the Standardization Committee of the Felt Association, Inc., and in accordance with the ASTM tests indicated in the document. The commercial trade designations of the more commonly used grades of automotive felts are given along with complete specifications and tolerances for thickness, mass, wool content, chemical and physical requirements, color, and width. General information, recommended uses, etc., are published in Appendix A as a guide in the selection of felts for particular uses, but the requirements for each application should be taken into consideration in making final selections.
Standard

Felts--Wool and Part Wool

2002-07-17
HISTORICAL
J314_200207
This SAE Standard identifies chemical/mechanical properties, thickness, width, mass, and other requirements recommended for felts (refer to Tables 1 and 2). It was developed with the cooperation of the Standardization Committee of the Felt Association, Inc., and in accordance with the ASTM tests indicated in the document. The commercial trade designations of the more commonly used grades of automotive felts are given along with complete specifications and tolerances for thickness, mass, wool content, chemical and physical requirements, color, and width. General information, recommended uses, etc., are published in Appendix A as a guide in the selection of felts for particular uses, but the requirements for each application should be taken into consideration in making final selections.
Standard

Instrumental Color Difference Measurement for Exterior Finishes, Textiles and Colored Trim

2005-07-25
HISTORICAL
J1545_200507
The practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials that are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film.
Standard

Instrumental Color Difference Measurements for Colorfastness of Automotive Interior Trim Materials

2019-06-05
WIP
J1767
The practice described applies to textile and flexible plastic parts and materials used in automotive vehicles. Special care should be taken when high pile carpet samples are being evaluated. The intent of this SAE Recommended Practice is to specify procedures for the instrumental measurement of color differences brought about by the exposure of textile and flexible plastic automotive parts to various colorfastness tests. It may be used for the specification of limits of color differences which may be tolerated in a specific test.
Standard

Method of Testing Resistance to Crocking of Organic Trim Materials

2012-08-24
CURRENT
J861_201208
This test can be used to determine the resistance to crocking (color rub-off) of organic trim materials such as fabrics, vinyl coated fabrics, leather, coated fiberboard and carpet. This method is similar to AATCC Method 8 –Colorfastness to Crocking.
Standard

Outdoor Weathering of Exterior Materials

2012-04-16
CURRENT
J1976_201204
This test method specifies the exposure racks, black boxes, and instrumentation, which shall be used for the outdoor weathering of materials for automotive exterior application.
Standard

Procedure for Visual Evaluation of Interior and Exterior Automotive Trim

2013-08-14
HISTORICAL
J361_201308
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim.
Standard

Procedure for Visual Evaluation of Interior and Exterior Automotive Trim

2016-11-18
HISTORICAL
J361_201611
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
Standard

Procedure for Visual Evaluation of Interior and Exterior Automotive Trim

2017-04-17
CURRENT
J361_201704
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100 Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
Standard

Seam Damage Test Procedure

2014-05-20
CURRENT
J1531_201405
This procedure is used to determine seam strength and seam fatigue of automotive textiles, vinyl coated fabrics and related soft trim materials.
Standard

Seam Damage Test Procedure

2008-05-02
HISTORICAL
J1531_200805
This procedure is used to determine seam strength and seam fatigue of automotive textiles, vinyl coated fabrics and related soft trim materials.
Standard

Test Method for Determining Cold Cracking of Flexible Plastic Materials

2009-11-09
CURRENT
J323_200911
This SAE Recommended Practice is applicable for determining the cold characteristics of flexible plastic materials, as applicable. It consists of three different methods for determining low-temperature properties of materials depending on type of material and end use. The method used shall be as specified by the contractual parties.
X