2024-03-19
Search Results
2024-03-19
2024-03-19
Technical Paper
10 KWe Dual-Mode Space Nuclear Power System for Military and Scientific Applications
1992-08-03
929072
A 10 KWe dual-mode space power system concept has been identified which is based on INEL's Small Externally-fueled Heat Pipe Thermionic Reactor (SEHPTR) concept. This power system will enhance user capabilities by providing reliable electric power and by providing two propulsion systems; electric power for an arc-jet electric propulsion system and direct thrust by heating hydrogen propellant inside the reactor. The low thrust electric thrusters allow efficient station keeping and long-term maneuvering. The direct thrust capability can provide tens of pounds of thrust at a specific impulse of around 730 seconds for maneuvers that must be performed more rapidly. The direct thrust allows the nuclear power system to move a payload from Low Earth Orbit (LEO) to Geosynchronous Earth Orbit (GEO) in less than one month using approximately half the propellant of a cryogenic chemical stage.
Technical Paper
1970s Development of 21st Century Mobile Dispersed Power
1973-02-01
730709
A mobile and dispersed power system is necessary for an advanced technological-industrial society. Today's petroleum-based system discharges waste products and heat and is growing exponentially. Energy resource commitment has already intersected “ultimate” low-cost petroleum supplies in the United States and will do so for the world before 2000; this portends major changes and cost increases. The twenty-first century system for mobile-dispersed power will reflect the energy source selected to replace petroleum-for example, coal, solar insolation, or uranium. It will incorporate a fuel intermediate such as methanol, ammonia, or hydrogen, and a suitably matched “engine.” The complete change will require more than 25 years because of the magnitude, fragmentation, structural gaps, complexity, and variety of the mobile-dispersed power system.
Technical Paper
2-Cycle Methanol LHR Engine and It's Characteristics
1994-10-01
941910
Methanol fuel was tested in a prototype 2-cycle ceramic heat insulated engine with a swirl chamber. It was found that the 2-cycle ceramic heat insulated engine with a compression ratio of 18:1 could ignite methanol without an auxiliary ignition system and emissions were substantially reduced in the whole load range.
Technical Paper
A 3D-CFD Numerical Approach for Combustion Simulations of Spark Ignition Engines Fuelled with Hydrogen: A Preliminary Analysis
2023-04-11
2023-01-0207
With growing concern about global warming, alternatives to fossil fuels in internal combustion engines are searched. In this context, hydrogen is one of the most interesting fuels as it shows excellent combustion properties such as laminar flame speed and energy density. In this work a CFD methodology for 3D-CFD in-cylinder simulations of engine combustion is proposed and its predictive capabilities are validated against test-bench data from a direct injection spark-ignition (DISI) prototype. The original engine is a naturally aspirated, single cylinder compression ignition (Diesel fueled) unit. It is modified substituting the Diesel injector with a spark plug, adding two direct gas injectors, and lowering the compression ratio to run with hydrogen fuel. A 3D-CFD model is built, embedding in-house developed ignition and heat transfer models besides G-equation one for combustion.
Technical Paper
A 3D-Simulation with Detailed Chemical Kinetics of Combustion and Quenching in an HCCI Engine
2008-06-23
2008-01-1655
A 3D-CFD model with detailed chemical kinetics was developed to investigate the combustion characteristics of HCCI engines, especially those fueled with hydrogen and n-heptane. The effects of changes in some of the key important variables that included compression ratio and chamber surface temperature on the combustion processes were investigated. Particular attention was given, while using a finer 3-D mesh, to the development of combustion within the chamber crevices between the piston top-land and cylinder wall. It is shown that changes in the combustion chamber wall surface temperature values influence greatly the autoignition timing and location of its first occurrence within the chamber. With high chamber wall temperatures, autoignition takes place first at regions near the cylinder wall while with low surface temperatures; autoignition takes place closer to the central region of the mixture charge.
Technical Paper
A Before Treatment Method for Reduction of Emissions in Diesel Engines
2000-10-16
2000-01-2791
Through an addition of a small amount of hydrogen to the main fuel, combustion process can be considerably enhanced in internal combustion engines producing significantly lower levels of exhaust emissions. This improvement in combustion can be mainly attributed to the faster and cleaner burning characteristics of hydrogen in comparison to conventional liquid and gaseous fuels. An oxygen-enrichment of a fuel-air mixture also improves thermal efficiency and reduces especially particulate, carbon monoxide and unburned hydrocarbon emissions in exhaust. This contribution describes the results of experimental investigation where a small amount of hydrogen and oxygen is produced by Hydrogen Generating System through the electrical dissociation of water and are added to the intake of a compression ignition engine operating on a commercial diesel fuel. It is shown that level of exhaust emissions including NOx can be moderately reduced using such a pre-treatment method in diesel engines.
Technical Paper
A COMPARISON OF GRID-CONNECTED HYBRID AND HYDROGEN FUEL-CELL ELECTRIC VEHICLES
2007-09-16
2007-24-0073
For fuelling road transportation in the future, particularly light-duty vehicles, there has been much speculation about the use of hydrogen and fuel cells to provide electrical power to an all-electric drive train. An alternative powertrain would use a simple battery to store electricity directly, using power from the electrical grid to charge the battery when the vehicle is not in use. The energy efficiency of these two different approaches has been compared, using a complete “energy conversion chain analysis”. The successful development and introduction into the marketplace of grid-connected hybrid vehicles could eliminate the need for road vehicles to use petroleum fuels, at least for the majority of miles traveled. If electricity were to be generated primarily from sustainable primary energy sources, then road transportation would also become sustainable, resulting in an “Electricity Economy”, rather than a “Hydrogen Economy.
Technical Paper
A Characterization of Exhaust Emissions from Lean Burn, Rotary, and Stratified Charge Engines
1977-02-01
770301
This paper reports the results of an exhaust emissions characterization from the non-catalyst control systems employed on the Mazda RX-4 rotary, the Honda CVCC, and the Chrysler electronic lean burn. Throughout the paper, exhaust emissions from these vehicles are compared to those from a Chrysler equipped with an oxidation catalyst and an air pump. The emissions characterized are carbon monoxide, hydrocarbons, nitrogen oxides, sulfur dioxide, sulfates, hydrogen sulfide, carbonyl sulfide, hydrogen cyanide, aldehydes, particulate matter, and detailed hydrocarbons. A brief description of the sampling and analysis procedures used is included within the discussion.
Technical Paper
A Combustion Products Analyzer for Contingency Use During Thermodegradation Events on Spacecraft
1991-07-01
911479
As mission length and the number and complexity of payload experiments increase, so does the probability of thermodegradation contingencies (e.g. fire, chemical release and/or smoke from overheated components or burning materials), which could affect mission success. When a thermodegradation event occurs on board a spacecraft, potentially hazardous levels of toxic gases could be released into the internal atmosphere. Experiences on board the Space Shuttle have clearly demonstrated the possibility of small thermodegradation events occurring during even relatively short missions. This paper will describe the Combustion Products Analyzer (CPA), which is being developed under the direction of the Toxicology Laboratory at Johnson Space Center to provide necessary data on air quality in the Shuttle following a thermodegradation incident.
Technical Paper
A Compact 10 kW Electric Power Range Extender Suitable for Plug-In and Series Hybrid Vehicles
2011-09-11
2011-24-0085
The paper discusses the concept, specification and overall performance of a 10 kW electric power range extender suitable for electric plug-in and series hybrid vehicles, based on a single cylinder, high speed, four stroke internal combustion engine, tested and developed at Istituto Motori CNR of Italy. This unit has been conceived from the beginning as a compact on board recharging system for the mentioned kind of means, and especially for city cars and small commercial vehicles. The paper starts by defining some characteristics, advantages and drawbacks of an electric city car, followed by the criteria adopted to characterize the nominal power of the range extender. Then, the ratio which leaded to the adoption of a single cylinder internal combustion engine is discussed, followed by an explanation of the main design characteristics of the whole unit.
Technical Paper
A Comparative Analysis of Alternative Fuel Infrastructure Requirements
1989-09-01
892065
This paper presents results of an assessment that identifies vehicle technology and fuel distribution system changes and costs associated with providing sufficient alternative fuels to displace one million barrels/day petroleum in the transportation sector in the 1995-2005 timeframe. The paper concludes that the capital cost of developing fuel delivery systems and a sufficient number of vehicles to achieve this displacement will be $22 billion if the alternative fuel is methanol, $36 billion if natural gas, and $288 billion if electricity. The predominant component of these costs is that of the incremental cost of the vehicles.
Journal Article
A Comparative Assessment of Electric Propulsion Systems in the 2030 US Light-Duty Vehicle Fleet
2008-04-14
2008-01-0459
This paper quantifies the potential of electric propulsion systems to reduce petroleum use and greenhouse gas (GHG) emissions in the 2030 U.S. light-duty vehicle fleet. The propulsion systems under consideration include gasoline hybrid-electric vehicles (HEVs), plug-in hybrid vehicles (PHEVs), fuel-cell hybrid vehicles (FCVs), and battery-electric vehicles (BEVs). The performance and cost of key enabling technologies were extrapolated over a 25-30 year time horizon. These results were integrated with software simulations to model vehicle performance and tank-to-wheel energy consumption. Well-to-wheel energy and GHG emissions of future vehicle technologies were estimated by integrating the vehicle technology evaluation with assessments of different fuel pathways. The results show that, if vehicle size and performance remain constant at present-day levels, these electric propulsion systems can reduce or eliminate the transport sector's reliance on petroleum.
Technical Paper
A Comparative Review of Fuel Cell Vehicles (FCVs) and Hybrid Electric Vehicles (HEVs) Part II: Control Strategies, Power Train, Total Cost, Infrastructure, New Developments, and Manufacturing & Commercialization
2003-06-23
2003-01-2299
In this paper, a number of issues of concern in relation to hybrid electric vehicles (HEVs) and fuel cell vehicles (FCVs) are discussed and comparatively reviewed. Currently, almost all the activities in the development of new generation of vehicles are focused on FCVs and HEVs. However, there are still uncertainties as to which provides the maximum benefits in terms of performance, energy savings, impact on environment etc. In particular, potential control strategies for FCVs and HEVs will be discussed and compared. For FCVs, these include power-averaging control as well as control based on maximum conversion efficiency, among others. HEV control strategies include electrically peaking hybrid propulsion, and parameter optimization approaches such as battery SOC maximization, emissions minimization, and optimal power management.
Technical Paper
A Comparative Study of Methanol-Gasoline Blends on Performance and Emissions on BS-IV and BS-VI Class of Two Wheeler Vehicles
2024-01-16
2024-26-0073
Methanol, a fuel obtainable through the capture and conversion of Carbon Dioxide (CO2), has garnered attention as a suitable alternative fuel for gasoline. Methanol-gasoline blends, characterized by their high-octane rating, commendable performance, and reduced carbon emissions, present themselves as promising alternative fuels for internal combustion engines. In the present study, a comprehensive comparative analysis was conducted to assess the performance and emissions characteristics of unmodified vehicles utilizing methanol blends at lower concentrations, ranging up to 30%, in gasoline. The research focused on two distinct classes of vehicles commonly found on the roads of India: those compliant with BS-IV (Euro IV) and BS-VI (Euro VI) emission standards. Experimental evaluations were carried out on a chassis dynamometer, with the vehicles subjected to the Worldwide Harmonized Motorcycle Test Cycle (WMTC) and Wide open throttle (WOT) driving tests.
Technical Paper
A Comparative Study on Different Methods of Using Waste Cooking Oil as Fuel in a Compression Ignition Engine
2017-03-28
2017-01-0876
Different methods to improve the performance of a WCO (waste cooking oil of sunflower) based mono cylinder compression ignition (CI) engine were investigated. Initially WCO was converted into its emulsion by emulsification process and tested as fuel. In the second phase, the engine intake system was modified to admit excess oxygen along with air to test the engine with WCO and WCO emulsion as fuels under oxygen enriched environment. In the third phase, the engine was modified to work in the dual fuel mode with hydrogen being used as the inducted fuel and either WCO or WCO emulsion used as the pilot fuel. All the tests were carried out at 100% and 40% of the maximum load (3.7 kW power output) at the rated speed of 1500 rpm. Engine data with neat diesel and neat WCO were used for comparison. WCO emulsion indicated considerable improvement in performance. The smoke and NOx values were noted to be less than neat WCO.
Technical Paper
A Comparative Study on the Effect of Alcohol Induction and Addition on Performance Behavior of a CI Engine Fueled with “Madhuca Indica” as Fuel
2015-04-14
2015-01-0853
The effect of methanol addition (by blending) and methanol induction (by carburetion) on performance of a vegetable oil (Madhuca Indica called as Mahua oil) based diesel engine was studied experimentally. A single cylinder, water cooled, DI, diesel engine was used. Baseline data was generated with neat diesel and neat Mahua oil as fuels. Subsequently methanol was blended with Mahua oil in different proportions such as 5, 10, 15 and 20% by mass and tested for engine's performance. Finally the engine was operated in dual fuel mode of operation with methanol induction and Mahua oil injection. Engine performance, emission and combustion characteristics of ND (neat diesel), NMO (neat Mahua oil), MOMB (Mahua oil+15% methanol blend by mass) and MOMDFE (Mahua oil dual fuel engine at 15% mass share) were compared and analyzed at 100% and 40% loads. NMO resulted in inferior performance and increased emissions at both power outputs as compared to ND.
Technical Paper
A Comparison Between the Combustion of Isooctane, Methanol, and Methane in Pulse Flame Combustors with Closed Loop A/F Control
1992-02-01
920799
CO/H2 (ratios i.e. water gas shift equilibria) in exhaust gases produced from the combustion of pure isooctane, methanol, and methane in a pulse flame combustor were measured. Measured CO/H2 ratios were directionally consistent with C/H ratios of the respective fuels. The average CO/H2 ratios in combusted isooctane, methanol, and methane were found to be 3.8, 1.25, and 2.0, respectively. The effect of these differences on feedback A/F control with a HEGO (heated exhaust gas oxygen) sensor were also examined. Feedback control of isooctane combustion produced operation very near to stoichiometry. On the other hand, the combustion of methanol under feedback control resulted in steady state lean operation while feedback control of methane combustion produced rich operation. For all three fuels, operation shifted in the lean direction as combustion efficiency was degraded.