Standards Under Development (WIP)

Automotive

Viewing 1 to 50 of 454

Document Title Date Committee
J3187 Applying System Theoretic Process Analysis (STPA) to Automotive Applications
Scope of this effort intends to provide both educational material and recommended practices in regards to how STPA may be applied within a safety assessment process focusing on automotive vehicle safe...
2018-09-20 Functional Safety Committee -
J2039 Side Turn Signal Lamps for Long Vehicles
This SAE Recommended Practice provides test procedures, requirements, and guidelines for side turn signal lamps intended for use on vehicles 12 m or more in overall length, except pole trailers. Side ...
2018-09-20 Heavy Duty Lighting Standards Committee -
J1839 Coarse Droplet Water/Fuel Separation Test Procedure
To determine the undissolved water removal performance of a fuel/water separator under controlled laboratory conditions, using water droplets.
2018-09-20 Filter Test Methods Standards Committee -
J905 Fuel Filter Test Methods
The purpose of this fuel filter test method is to provide standardized methods for evaluating the performance characteristics of fuel filters by bench test methods. This, combined with data obtained f...
2018-09-20 Filter Test Methods Standards Committee -
J2945/8 Cooperative Perception System
This document provides a description for a V2X-capable device such as a vehicle, an infrastructure or a portable device to broadcast its perception information of other road users/objects nearby, to r...
2018-09-18 DSRC (Dedicated Short Range Communication) Tech Cmte -
J2945/7 Positioning Enhancements for V2X systems
This WIP delivers a technical report with the intent of leveraging existing specifications and reports for V2X positioning enhancements, e.g.SAE6857 Requirements for a Terrestrial Based Positioning, N...
2018-09-17 DSRC (Dedicated Short Range Communication) Tech Cmte -
J3183 Nonmetallic EGR Tubing with One or More Layers
This SAE Standard presents the minimum requirements for nonmetallic tubing with one or more layers manufactured for use in exhaust gas recirculation systems Requirements in this document apply to mono...
2018-09-11 Plastics Committee -
J3184 Diesel Exhaust Fluid (DEF) tubing with one or more layers
This SAE Standard presents the minimum requirements for nonmetallic tubing with one or more layers manufactured for use as liquid carrying DEF lines for diesel engine selective catalyst reduction (SCR...
2018-09-11 Plastics Committee -
J3185 Nonmetallic Air Suspension System Tubing with One or More Layers
This SAE Standard presents the minimum requirements for nonmetallic tubing with one or more layers manufactured for use as pneumatic tubing in automotive air suspension lines. Requirements in this doc...
2018-09-11 Plastics Committee -
J3179 Condenser Corrosion Test Procedure
To develop a standard test procedure for assessing corrosion behavior of an MAC condenser
2018-09-11 Interior Climate Control MAC Supplier Committee -
J3182 Plastic Windshield Washer Tubing
This SAE Standard covers nonreinforced, extruded, plastic tubing intended primarily for use as fluid lines for automotive windshield washer systems which conform to the requirements of SAE J942.
2018-09-11 Plastics Committee -
J3181 Thermoplastic Coolant Tubes
Standard covers material performance requirements for extruded thermoplastic tubes used in engine coolant/water applications.
2018-09-11 Plastics Committee -
J3186 Maneuver Sharing and Coordinating service
This project will provide requirements to support applications for the Maneuver Sharing and Coordinating service (MSCS) in order to improve road safety and traffic efficiency by sharing and coordinati...
2018-09-11 Cellular V2X Technical Committee -
J216 Motor Vehicle Glazing--Electrical Circuits
This SAE Recommended Practice establishes limits for electrical circuits on motor vehicle safety glazing materials.
2018-08-31 Glazing Materials Standards Committee -
J2836/2 Use Cases for Communication between Plug-in Vehicles and Off-Board DC Charger
This SAE Information Report SAE J2836/2TM establishes use cases and general information for communication between plug-in electric vehicles and the DC Off-board charger. Where relevant, this document ...
2018-08-30 Hybrid - EV Committee -
J2344 Guidelines for Electric Vehicle Safety
This SAE Information Report identifies and defines the preferred technical guidelines relating to safety for Electric Vehicles (EVs) during normal operation and charging. Guidelines in this document d...
2018-08-30 Hybrid - EV Committee -
J2312 Automatic Transmission Intake Filter Test Procedure
This test procedure is intended to apply to hydraulic pump suction filters and strainers used in automotive automatic transmissions that include hydraulic power pumps. The various paragraphs of Sectio...
2018-08-28 Automatic Transmission and Transaxle Committee -
J1889 L.E.D. Signal and Marking Lighting Devices
This SAE Recommended Practice applies to functions of motor vehicle signaling and marking lighting devices which use light emitting diodes (L.E.D.’s) as light sources. This report provides test method...
2018-08-24 Signaling and Marking Devices Stds Comm -
J1742 Connections for High Voltage On-Board Road Vehicle Electrical Wiring Harnesses - Test Methods and General Performance Requirements
SCOPE Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and comp...
2018-08-23 Connector Systems Standards Committee -
J928 Electrical Terminals--Pin and Receptacle Type
This SAE Standard covers general requirements and terminal interface dimensions of various sizes of pin and receptacle type terminals.
2018-08-23 Connector Systems Standards Committee -
J561 Electrical Terminals--Eyelet and Spade Type
This SAE Standard covers general requirements and dimensions of various sizes of eyelet and spade type terminals.
2018-08-23 Connector Systems Standards Committee -
J1453/2 Specification for O-Ring Face Seal Connectors: Part 2 - Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Braze-on Tube Ends, Caps, and Connectors with ISO 6149-2 Metric Stud Ends and ISO 6162 4-Bolt Flange Heads
The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal (ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose...
2018-08-23 Hydraulic Tube Fittings Committee -
J1239 Four-, Five-, and Eight-Conductor Electrical Connectors for Automotive Type Trailers
This SAE Recommended Practice covers the wiring and rectangularly shaped connector standards for all types of trailers whose gross weight does not exceed 4540 kg (10 000 lb). These trailers are groupe...
2018-08-23 Connector Systems Standards Committee -
J1237 Metric Thread Rolling Screws
This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.
2018-08-20 Fasteners Committee -
J1737 Test Procedure to Determine the Hydrocarbon Losses from Fuel Tubes, Hoses, Fittings, and Fuel Line Assemblies by Recirculation
This SAE Recommended Practice is intended for the determination of the losses of hydrocarbon fluids, by permeation through component walls as well as through 'microleaks' at interfaces of assembled co...
2018-08-13 Fuel Systems Standards Committee -
J2380 Vibration Testing of Electric Vehicle Batteries
This SAE Recommended Practice describes the vibration durability testing of a single battery (test unit) consisting of either an electric vehicle battery module or an electric vehicle battery pack. Fo...
2018-08-09 Battery Standards Testing Committee -
J3178 Adhesives, Sealants, and Heat Transfer Materials in Battery Systems: A Primer on Applications, Manufacturing and End-Use Performance Requirements
This document provides an overview of adhesives, sealants, and heat transfer materials commonly used in battery packs. Specific attention is given to the location where such materials are used within ...
2018-07-30 Battery Systems Adhesives, Sealants and Heat Transfer Matl's -
J1939/81 Network Management
SAE J1939-81 Network Management defines the processes and messages associated with managing the source addresses of applications communicating on an SAE J1939 network. Network management is concerned ...
2018-07-23 Truck Bus Control and Communications Network Committee -
J1993 High-Carbon Cast-Steel Grit
This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.
2018-07-23 Surface Enhancement Committee -
J445 Metallic Shot and Grit Mechanical Testing
This SAE Information Report is intended to provide users and producers of metallic shot and grit with general information on methods of mechanically testing metal shot in the laboratory.
2018-07-23 Surface Enhancement Committee -
J441 Cut Wire Shot
This SAE Recommended Practice is considered to be tentative and is subject to modification to meet new developments or requirements. It is offered as a guide in the selection and use of cut wire shot.
2018-07-23 Surface Enhancement Committee -
J1645 Fuel Systems and Components - Electrostatic Charge Mitigation
This SAE Surface Vehicle Recommended Practice deals with electrostatic charge phenomena that may occur in automotive fuel systems and applies to the following: • Fuels that are in a liquid state at am...
2018-07-23 Fuel Systems Standards Committee -
J827 High-Carbon Cast-Steel Shot
This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high carbon cast-steel shot to be used for shot peening or blast cleaning operations.
2018-07-23 Surface Enhancement Committee -
J306 Automotive Gear Lubricant Viscosity Classification
This SAE Standard defines the limits for a classification of automotive gear lubricants in rheological terms only. Other lubricant characteristics are not considered.
2018-07-18 Fuels and Lubricants TC 3 Driveline and Chassis Lubrication -
J2836/1 Use Cases for Communication Between Plug-in Vehicles and the Utility Grid
This SAE Information Report J2836 establishes use cases for communication between plug-in electric vehicles and the electric power grid, for energy transfer and other applications.
2018-07-16 Hybrid - EV Committee -
J2847/1 Communication for Smart Charging of Plug-in Electric Vehicles using Smart Energy Profile 2.0
This document describes the details of the Smart Energy Profile 2.0 (SEP2.0) communication used to implement the functionality described in the SAE J2836/1™ use cases. Each use case subsection include...
2018-07-16 Hybrid - EV Committee -
J2867 Laboratory Testing of Light Duty Vehicle Electric Cooling Fan Assemblies for Airflow Performance

This SAE Recommended Practice is intended for use in testing and evaluating the performance of Light Duty automotive electric engine cooling fans. These Electric Cooling Fan (ECF) Assemblies are pu...

2018-07-13 Cooling Systems Standards Committee -
J1004 Glossary of Engine Cooling System Terms
The objective of this glossary is to establish uniform definitions of parts and terminology for engine cooling systems. Components included are all those through which engine coolant is circulated: wa...
2018-07-13 Cooling Systems Standards Committee -
J2883 Laboratory Measurement of Random Incidence Sound Absorption Tests Using a Small Reverberation Room
This SAE Recommended Practice describes a laboratory test procedure for measuring the random incidence sound absorption performance of a material or a part in a small size reverberation room by measur...
2018-07-10 Acoustical Materials Committee -
J2807 Performance Requirements for Determining Tow-Vehicle Gross Combination Weight Rating and Trailer Weight Rating
This document establishes minimum performance criteria at GCWR and calculation methodology to determine tow-vehicle TWR for passenger cars, multipurpose passenger vehicles and trucks. This includes al...
2018-06-28 Tow Vehicle Trailer Rating Committee -
J3138 Diagnostic Link Connector Security
This document describes some of the actions that should be taken to help ensure safe vehicle operation in the case that any such connected device (external test equipment, connected data collection de...
2018-06-23 Data Link Connector Vehicle Security Committee -
J2534/1 Recommended Practice for Pass-Thru Vehicle Programming
This SAE Recommended Practice describes a standardized interface that connects between a standard personal computer (PC) and vehicle. The purpose of this interface is to enable the reprogramming of em...
2018-06-14 Vehicle E E System Diagnostic Standards Committee -
J175 Wheels - Lateral Impact Test Procedure - Road Vehicles
The SAE Recommended Practice establishes minimum performance requirements and related uniform laboratory test procedures for evaluating lateral (curb) impact collision resistance of all wheels intende...
2018-06-03 Wheel Standards Committee -
AIR6975 Hard Bearing Balancing Machine Technology - Proper Use of Rotor Type-Specific Calibration
The scope of this Aerospace Information Report includes practical applications; theory; process management, audit, and control recommendations; recommended validation intervals; verification and valid...
2018-05-30 EG-1A Balancing Committee -
J2487 SAE No. 2 Friction Test Machine 3600 r/min Stepped Power Test
This SAE Recommended Practice is intended as the definition of a standard test, but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind w...
2018-05-30 Automatic Transmission and Transaxle Committee -
J2488 SAE No.2 Friction Test Machine 6000 r/min Stepped Power Test
This SAE Recommended Practice is intended as the definition of a standard test, but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind w...
2018-05-30 Automatic Transmission and Transaxle Committee -
J2490 SAE No. 2 Friction Test Machine μPVT Test
This SAE Recommended Practice is intended as the definition of a standard test, which may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind...
2018-05-30 Automatic Transmission and Transaxle Committee -
J3177 Incorporating Shared and Digital Mobility Services into Household Travel Surveys
This Recommended Practice addresses data collection techniques regarding shared and digital mobility services in the context of household travel surveys. It recognizes the diversity in contemporary mo...
2018-05-24 Shared and Digital Mobility Committee -
J1477 Measurement of Interior Sound Levels of Light Vehicles
This SAE Recommended Practice establishes the test procedure, environment, instrumentation, and data analyses for comparing interior sound level of passenger cars, multipurpose vehicles, and light tru...
2018-05-24 Light Vehicle Exterior Sound Level Standards Committee -
J1352 Compression and Recovery of Insulation Paddings
This test method is applicable for determining the relative compression and recovery of fibrous insulation padding materials. 1.1 Purpose The purpose of this test method is to establish a means of mea...
2018-05-24 Acoustical Materials Committee -

X