Standards Under Development (WIP)

Commercial Vehicle

Viewing 1 to 50 of 113

Document Title Date Committee
J2698 Primary Single Phase Nominal 120 VAC Wiring Distribution Assembly Design - Truck and Bus
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 V...
2022-05-18 Truck and Bus Electrical Systems Committee -
J1842 Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for whi...
2022-05-17 Truck and Bus Wheel Committee -
J444 Cast Shot and Grit Size Specifications for Peening and Cleaning
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal t...
2022-05-11 Surface Enhancement Committee -
J3078/2 Off-Road Self-Propelled Work Machines Operator enclosure environment Part 2:Air filter element test method
SAE J3078/2 specifies two uniform test methods to determine performance levels for fresh and recirculation air filters used in operator enclosures with an air ventilation system. It is not applicable ...
2022-05-06 HFTC6, Operator Accommodation -
J1533 Air Filter Element Test Method
This SAE test method establishes a uniform test procedure for determining the gravimetric (mass based) efficiency and pressure drop performance levels of operator enclosure panel type filters on off-r...
2022-05-06 HFTC6, Operator Accommodation -
J89 Dynamic Cushioning Performance Criteria for Snowmobile Seats
This SAE Recommended Practice encompasses the significant factors which determine the effectiveness of a seat system in limiting spinal injury during vertical impacts between the rider and the snowmob...
2022-05-02 Snowmobile Technical Committee -
J1609 Air Reservoir Capacity Performance Guide - Trucks and Buses

This SAE Recommended Practice establishes performance guidelines of the air reservoir systems used on trucks, towing trucks, truck-tractors, trailers, and converter dollies, with GVWRs over 10 000 ...

2022-04-29 Truck and Bus Brake Supply and Control Components Committee -
J1730 ABS Exciter Ring Location Standardization
This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of spoke whe...
2022-04-28 Truck and Bus Wheel Committee -
J2580 Identification and Installation of Air Brake System Components
This Recommended Practice covers air braked trucks, truck-tractors, trailers and buses. It enumerates the identification and installation of the air brake components not covered in other SAE recommend...
2022-04-28 Truck and Bus Brake Systems Committee -
J533 Flares for Tubing

This SAE Standard covers specifications and performance requirements for 37 degree and 45 degree single and double flares for tube ends intended for use with SAE J512, SAE J513, SAE J514, and ISO 8...

2022-04-25 Hydraulic Tube Fittings Committee -
J2899 Brake Adjustment Limit for Air Brake Actuators
This SAE Recommended Practice applies to S-CAM, Wedge, and Disc air brake actuators where the stroke can be measured without disassembly from the brake.
2022-04-25 Truck and Bus Brake Actuator Committee -
J3057 Ambulance Modular Body Evaluation-Quasi-Static Loading for Type I and Type III Modular Ambulance Bodies
This SAE Recommended Practice describes the test procedures for conducting quasi-static modular body strength tests for ambulance applications. Its purpose is to establish recommended test practices w...
2022-04-19 Truck Crashworthiness Committee -
J3027 Ambulance Litter Integrity, Retention, and Patient Restraint
This SAE Recommended Practice describes the testing procedures required to evaluate the integrity of a ground ambulance-based patient litter, litter retention system, and patient restraint when expose...
2022-04-19 Truck Crashworthiness Committee -
J3058 Ambulance Interior Storage Compartment Integrity
This SAE Recommended Practice describes the dynamic testing procedures required to evaluate the integrity of patient compartment interior Storage Compartments such as cabinets, drawers, or refillable ...
2022-04-19 Truck Crashworthiness Committee -
J3059 Ambulance Patient Compartment Seated Occupant Excursion Zone Evaluation
This SAE Information Report describes the testing and reporting procedures that may be used to evaluate and document the excursion of a worker or civilian when transported in a seated and restrained p...
2022-04-19 Truck Crashworthiness Committee -
J3102 Ambulance Patient Compartment Structural Integrity Test to Support SAE J3027 Compliant Litter Systems
This SAE Recommended Practice describes the dynamic and static testing procedures required to evaluate the integrity of the ambulance substructure, to support the safe mounting of an SAE J3027 complia...
2022-04-19 Truck Crashworthiness Committee -
J2917 Occupant Restraint and Equipment Mounting Integrity – Frontal Impact Ambulance Patient Compartment
This SAE Recommended Practice describes the test procedures for conducting frontal impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its ...
2022-04-19 Truck Crashworthiness Committee -
J2956 Occupant Restraint and Equipment Mounting Integrity – Side Impact Ambulance Patient Compartment
This SAE Recommended Practice describes the test procedures for conducting side impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its pur...
2022-04-19 Truck Crashworthiness Committee -
J99 Lighting and Marking of Industrial Equipment on Highways
To provide specifications for lighting and marking of industrial wheeled equipment whenever such equipment is operated or traveling on a highway.
2022-04-06 OPTC3, Lighting and Sound Committee -
J1834 Seat Belt Comfort, Fit, and Convenience - Truck and Bus
This SAE Recommended Practice provides design, test, and performance guidelines on the comfort, fit, and convenience for active restraint systems for heavy trucks and multipurpose passenger vehicle ap...
2022-04-04 Truck Crashworthiness Committee -
J3078/3 Off-Road Self-Propelled Work Machines Operator Enclosure Environment Part 3: Operator Enclosure Pressurization System Test Procedure

SAE J3078/3 establishes a uniform test procedure for evaluating performance of operator enclosure pressurization systems. This standard is applicable to off-road, self-propelled work machine, as de...

2022-03-14 HFTC6, Operator Accommodation -
J2267 Minimum Performance Criteria for Operator Front Protective Structure (OFPS) for Certain Equipment
This SAE standard applies to all forestry machines exposed to the hazard of objects penetrating the front of the operator station (other than the roof). This would include: Front guards for yarders wi...
2022-03-11 MTC4, Forestry and Logging Equipment -
J1939-77 Safety Assurance Trailers for SAE J1939-22 C-PGs
This document specifies the technical requirements for several different trailers that may be incorporated into J1939-22 C-PG payloads to provide safety assurance data. Proper use of these trailers is...
2022-02-25 Truck Bus Control and Communications Network Committee -
J2519 Guidelines and Procedures for Directional Drilling Tracking Operators
These general guidelines and precautions apply to personnel operating directional drilling tracking equipment when used with Horizontal Earthboring Machines as defined in SAE J2022.
2022-02-24 MTC9, Trenching and Horizontal Earthboring Machines -
J2305 Hazard Reduction for Horizontal Earthboring Machines
This SAE standard applies to horizontal earthboring machines (SAE J2022) of the following types: a. Auger boring machines; b. Rod pushers; c. Rotary rod machines; d. Impact machines. This document doe...
2022-02-24 MTC9, Trenching and Horizontal Earthboring Machines -
J1939-91A On Board Diagnostics Implementation Guide
This document will provide recommendations to vehicle manufacturers and component suppliers in securing the SAE J1939 network from the cybersecurity risks. It is recognized that not every application ...
2022-02-21 Truck Bus Control and Communications Network Committee -
J1449 Small Craft - Graphic Symbols
This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipmen...
2022-02-18 Marine Technical Steering Committee -
J1939-22 CAN FD Data Link Layer
The SAE J1939 documents are intended for light-, medium-, and heavy-duty vehicles used on or off road, as well as appropriate stationary applications which use vehicle derived components (e.g., genera...
2022-02-09 Truck Bus Control and Communications Network Committee -
J1939 Serial Control and Communications Heavy Duty Vehicle Network - Top Level Document
This top level document provides a general overview of the SAE J1939 network and describes the subordinate document structure. This document includes definitions of terms and abbreviations which are u...
2022-02-06 Truck Bus Control and Communications Network Committee -
J1939-76 SAE J1939 Functional Safety Communications Protocol
This document provides the technical requirements for implementing the SAE J1939 Functional Safety Communication Protocol in a manner determined suitable for meeting industry applicable functional saf...
2022-01-06 Truck Bus Control and Communications Network Committee -
J2030 Heavy-Duty Electrical Connector Performance Standard
This SAE Standard encompasses connectors between two cables or between a cable and an electrical component and focuses on the connectors external to the electrical component. This document provides en...
2021-12-14 CTTC C2, Electrical Components and Systems -
J1939/21 Data Link Layer
The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road, as well as appropriate stationary applications which use vehicle derived components (e.g., generato...
2021-12-08 Truck Bus Control and Communications Network Committee -
J2527 Performance Based Standard for Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Xenon-Arc Apparatus
This SAE Standard specifies the operating procedures for a controlled irradiance, xenon-arc apparatus used for the accelerated exposure of various exterior automotive materials. The sample preparation...
2021-11-18 Textile and Flexible Plastics Committee -
J2848/1 Tire Pressure Monitoring Systems - For Medium and Heavy Duty Highway Vehicles
This SAE recommended practice defines the system and component functions, measurement metrics, testing methodologies for evaluating the functionality and performance of tire pressure systems, and reco...
2021-11-16 Truck and Bus Tire Committee -
J3060 Automotive and Heavy Duty Storage Battery Vibration
This SAE Standard serves as a guide for vibration testing procedures of Automotive and Heavy Duty storage batteries.
2021-11-10 Starter Battery Standards Committee -
J1393 Heavy Duty Vehicle Cooling Test Code
The purpose of this SAE Recommended Practice is to establish a testing procedure to determine the performance capability of heavy duty vehicle cooling systems to meet Original Equipment Manufacturer o...
2021-10-28 Cooling Systems Standards Committee -
J1301 Truck Deformation Classification
The scope and purpose of this SAE Recommended Practice is to provide a classification system for deformation sustained by trucks involved in collisions on the highway. Application of the document is l...
2021-09-27 Data Collection and Archiving Standards Committee -
J1116_202109 Categories of Off-Road Self-Propelled Work Machines
This SAE Standard applies to self-propelled off-road work machines. Included are the following categories: Earthmoving Implements and Attachments Forestry Road Building and Maintenance Specialized Min...
2021-09-27 Machine Technical Steering Committee -
J371_202109 Drain, Fill, and Level Plugs for Off-Road, Self-Propelled Work Machines
This SAE Recommended Practice applies to off-road, self-propelled work machine categories of earthmoving, forestry, road building and maintenance, and specialized mining machinery as defined in SAE J1...
2021-09-27 Machine Technical Steering Committee -
J1702 Self-Propelled Sweepers Sweep-Ability Performance
This SAE Standard establishes a method of disclosing the sweep-ability performance of self-propelled sweepers that use broom means for sweeping and collection, together with either a mechanical- or pn...
2021-09-24 MTC2, Sweeper, Cleaner, and Machinery -
J2258 Light Utility Vehicles
This SAE Standard defines requirements relating to the elements of design, operation, and maintenance of light utility vehicles. The safety specifications in this document apply to any self-propelled,...
2021-08-31 Special Purpose Vehicle Committee -
J3191_TEST1 Guidelines for Aerodynamic Assessment of Mass-Produced Cars and Light-Duty Trucks Using Computational Fluid Dynamics_TestDoc1
Guidelines for Aerodynamic Assessment of Mass-Produced Cars and Light-Duty Trucks Using Computational Fluid Dynamics_TestDoc_scope
2021-08-11 Test GV Committee 1 -
J1939-91 Security Recommendations for Interfaces to On-vehicle Networks
This document will provide recommendations to vehicle manufacturers and component suppliers in securing the SAE J1939-13 connector interface from the cybersecurity risks posed by the existence of this...
2021-08-06 Truck Bus Control and Communications Network Committee -
J44 Snowmobile Service Brake System
This SAE Standard establishes a uniform testing procedure and performance requirements for the level surface testing of hand-operated service brake systems on snowmobiles.
2021-07-21 Snowmobile Technical Committee -
J1526 SAE Fuel Consumption Test Procedure (Engineering Method)
This document describes a fuel-consumption test procedure that utilizes industry accepted data collection and statistical analysis methods to determine the difference in fuel consumption between vehic...
2021-07-08 Truck and Bus Aerodynamics and Fuel Economy Committee -
J1029 Lighting and Marking of Construction, Earthmoving Machinery
This SAE Standard establishes minimum requirements for lighting and marking earthmoving construction machinery as defined in SAE J1116, 1.1 Self-Propelled Construction Machines - Earthmoving (excludin...
2021-04-16 OPTC3, Lighting and Sound Committee -
J899 Operator's Seat Dimensions for Off-Road Self-Propelled Work Machines
For off-road work machines listed in SAE J1116.
2021-04-14 HFTC4, Operator Seating and Ride -
J920 Technical Publications for Off-Road Self-Propelled Work Machines
This Recommended Practice applies to technical publications which present instructions for the proper unloading, set-up, installations, pre-delivery inspection, operation, and servicing of off-road se...
2021-04-14 Machine Technical Steering Committee -
J2473 Self-Propelled Sweepers and Scrubbers - Maximum Gradient Rating During Hopper Discharge
This SAE Standard establishes the maximum gradient rating during hopper discharge of self-propelled, driver-operated sweepers and scrubbers as defined by SAE J2130-1 and SAE J2130-2.
2021-04-12 MTC2, Sweeper, Cleaner, and Machinery -
J994 Alarm—Backup—Electric Laboratory Performance Testing
The scope of this SAE Standard is the definition of the functional, environmental, and life cycle test requirements for electrically operated backup alarm devices primarily intended for use on off-roa...
2021-04-06 OPTC3, Lighting and Sound Committee -

X