Search Results

A novel computer vision technique for rapid measurement of surface coordinates is presented. The technique is based on the marriage of a digital fringe projection technique and a fringe-phase extraction algorithm. A digitally controlled video signal in the form of linear and parallel fringes of cosinusoidal intensity variation is projected onto an object. The fringe pattern is perturbed by the three-dimensional object surface with fringe-phase containing information on the depth of the object. A phase extraction algorithm is used to determine the fringe-phase distribution, from which the three-dimensional surface coordinates are determined. The theoretical basis of this technique and some experimental results are presented in this paper.

An investigation of the possibility to extend the 3-dimensional modeling capabilities from conventional diesel to the HCCI combustion mode simulation was carried out. Experimental data was taken from a single cylinder engine operating with early injections for the HCCI and a split-injection (early pilot+main) for the high speed Diesel engine operation. To properly phase the HCCI mode in the experiments, high amounts of cooled EGR and a decreased compression ratio were used. In numerical simulation performed using KIVA3-V code, modified to incorporate the Detailed Chemistry Approach the same conditions were reproduced. Special attention is paid on the analysis of the events leading up to the auto-ignition, which was reasonably well predicted.

Manufacturers of heavy-duty diesel engines are facing increasingly stringent, emission standards. These standards have motivated new research efforts towards improving the performance of diesel engines. The objective of the present program is to develop a comprehensive analytical model of the diesel combustion process that can be used to explore the influence of design changes. This will enable industry to predict the effect of these changes on engine performance and emissions. A major benefit of the successful implementation of such models is that engine development time and costs would be reduced through their use. The computer model is based on the three-dimensional KIVA-II code, with state-of-the-art submodels for spray atomization, drop breakup / coalescence, multi-component fuel vaporization, spray/wall interaction, ignition and combustion, wall heat transfer, unburned HC and NOx formation, and soot and radiation.

Ever increasing specific power of diesel engines has put huge demand on effective thermal management of the pistons for the desired reliability and durability. The piston temperature control is commonly achieved by injecting cooling oil into piston galleries, but the design of the cooling system as well as the boundary conditions used in FEA simulations have so far relied mostly on empirical methods. A numerical procedure using 3D computational fluid dynamics (CFD) has therefore been developed to simulate the cooling process and to estimate the cooling efficiency of gallery. The model is able to predict the detailed oil flow and heat transfer in gallery, of different designs and engine applications, under dynamic conditions. The resulted spatially resolved heat transfer coefficient from the CFD model, with better accuracy, enables improved prediction of piston temperature in finite element analysis (FEA).

The thermal performance of an engine coolant system is efficient when the engine head temperature is maintained within its optimum working range. For this, it is desired that air should not be entrapped in the coolant system which can lead to localized hot spots at critical locations. However, it is difficult to eliminate the trapped air pockets completely. So, the target is to minimize the entrapped air as much as possible during the coolant filling and deaeration processes, especially in major components such as the radiator, engine head, pump etc. The filling processes and duration are typically optimized in an engine test stand along with design changes for augmenting the coolant filling efficiency. However, it is expensive and time consuming to identify air entrapped locations in tests, decide on the filling strategy and make the design changes in the piping accordingly.

Increased torque values passing from engine to transmission have, increasingly become a problem regarding shaft misalignment. Engineers are restricted with regard to applying ISO standards when investigating bearing life cycles as they tend only to cover normal [radial thrust] load conditions. Depending on the application, the need has arisen for numerical models to determine reduction in normal life cycles due to abnormal running conditions. The Simulia Finite Element package Abaqus v6.7 provides trends in the deformations, contact pressures and their respective distribution. It was found the most efficient profile, with regards to a uniform contact pressure, under both radial and misaligned conditions is the toroidal profile.

A 3-D numerical analysis model of transient heat transfer among the multi-component coupling system in combustion chamber of internal combustion engine has been developed successfully in the paper. The model includes almost all solid components in combustion chamber, such as piston assembly, cylinder liner, cylinder head gasket, cylinder head, intake valves and exhaust valves, etc. With two different coupling heat transfer modes, one is the lubricant film heat conduction between two moving components, another is the contact heat conduction between two immovable solid components, and with the direct coupled-field analysis method of FEM, the heat transfer relation among the components is established. The simulation result dedicates the transient heat transfer process among the components such as moving piston assembly and cylinder liner, moving valves and cylinder head. The effect of cylinder head gasket on heat transfer among the components is also studied.

Nowadays, due to the stringent engine emission norms, an efficient technique is required to reduce oxides of nitrogen (NOx) from automobiles especially from the lean burn engines. Selective Catalytic Reduction (SCR) is found to be an efficient after treatment method used to reduce oxides of nitrogen (NOx) from the exhaust. However, for light duty vehicles, because of the limited size of the catalysts, ammonia slip nullifies its advantages. Lack of uniformity of ammonia at the SCR monolith entrance causes ammonia slip. This study addresses the effect of injection parameters, location of injector and shape of injector upon the flow parameters, exhaust gas temperature and flow rate. The results obtained from this study provide useful guidelines for optimizing the injection parameters to avoid the ammonia slip. The evaporation of Urea Water Solution (UWS) is also investigated.

The urea Selective Catalytic Reduction (SCR) exhaust system has been proved to be the reliable aftertreatment device with the capability of reducing tail pipe NOx emission by 75% to 90%, HC by 50% and Particulate Matter (PM) by 30%. Constrained by increasingly stringent packaging envelope, flow mixing in front of substrate is becoming one of the major concerns to achieve ideal performance of higher NOx conversion and lower ammonia (NH3) slip. Three dimensional CFD simulations are performed in current study to investigate flow mixing phenomenon in a SCR system. First, for a traditional tube injector with single or multiple nozzles, the effects of mass flow rates of injected NH3 and exhaust gas on flow mixing and pressure loss are investigated. Then, a concept of ring shape injector with multiple nozzles are initiated and built for 3-D CFD simulations. The comparisons of flow mixing index and injection pressure are made between two type injectors.

The main objective of the current paper was to investigate the fluid flow and pressure loss characteristics of DPF substrates with asymmetric channels utilizing 3-D Computational Fluid Dynamics (CFD) methods. The ratio of inlet to outlet channel width is 1.2. First, CFD results of velocity and static pressure distributions inside the inlet and outlet channels are discussed for the baseline case with both forward and reversed exhaust flow. Results were also compared with the regular DPF of same cell structure and wall material properties. It was found that asymmetrical channel design has higher pressure loss. The lowest pressure loss was found for the asymmetrical channel design with smaller inlet channels. Then, the effects of DPF length and filter wall permeability on pressure loss, flow and pressure distributions were investigated.

The Urea Selective Catalytic Reduction (SCR) technology is one of the major mature exhaust aftertreatment technologies which are demonstrated to be able to lower tail pipe NOx emission by 90%. The system consists of a urea injection at upstream pipe and a downstream SCR converter. A well mixed flow (exhaust gas and NH3) in front of SCR substrate, which is usually constrained by tight design packaging, is very critical to ensure the desired performance. Current paper addresses the geometrical effects on flow mixing by using three dimensional Computational Fluid Dynamics (CFD) tool. The mixing enhancement is achieved by adding flow mixer. The shapes and locations of flow mixers, as well as the number of blades inside mixer are investigated to show the effect on fluid mixing in downstream along the flow direction. Results show great improvement of flow mixing by adding a delta wing mixer.

Three-dimensional behaviors of direct injection (D.I.) gasoline sprays were investigated using 2-D and 3-D particle image velocimetry (PIV) techniques. The fuel was injected with a swirl type injector for D.I. gasoline engines into a constant volume chamber in which ambient pressure was varied from 0.1 to 0.4 MPa at room temperature. The spray was illuminated by a laser light sheet generated by a double-pulsed Nd:YAG laser (wave length: 532 nm) and the succeeding two tomograms of the spray were taken by a high-resolution CCD camera. The 2-D and 3-D velocity distributions of the droplet cloud in the spray were calculated from these tomograms by using the PIV technique. The effects of the swirl groove flows in the injector and the ambient pressure on the structural behavior of the droplet cloud in the spray were also examined.

In the design and development of modern cars with respect to comfort, silence and safety, state of the art experimental modal analysis is one of the essential development tools. Due to the large amount of degrees of freedom of such a large and complex system like a car with all its components, a complete simulation by FEM can not be realised easily and requires an enormous expenditure of work and calculations. In addition the simulations are based on assumed system parameters and thus the vibration behaviour of the resulting prototypes often is not completely identical to the simulated model. In contrast to conventional measurements with accelerometers, the 3-D Scanning Vibrometer enables fast and efficient non-contact measurements of the in-plane and out-of-plane vibration behaviour at all optical accessible surfaces. The method easily allows to increase the number of measured points to obtain a high measurement point density.

3-D shell components are used intensively in the automotive industry. Many structural topology optimization techniques were developed to reduced the total weight of shell structures while retaining its structural performance. One common approach is to utilize the concept of the design domain, such as the homogenization method and the density function approach. In this paper, a new micro-structure based design domain method is introduced to solve 3-D shell topology optimization problems. Based on physical micro-structure model, simple closed-form expressions for effective Young's modulus and effective shear modulus are rigorously derived. Using these simple relations, topology optimization problems can be formulated and solved with sequential convex approximation algorithms. Two design examples obtained from the new method are presented.

A three-dimensional model is used to compute the flow,sprays and combustion in a stratified-charge rotary engine. Wall temperatures estimated from available measurements are used as boundary conditions for the energy equation. The computations provide local and instantaneous heat fluxes on the rotor and the rotor housing. The instantaneous heat fluxes are integrated in time over one cycle of the rotor to obtain estimates of local cycle averaged heat flux through the rotor and the rotor housing. These are then used as boundary conditions in a thermal analysis of the rotor and rotor housing with known coolant-side flow rates and heat transfer coefficients. The thermal analysis is done using a finite-element three-dimensional code which provides updated estimates of the rotor and rotor housing wall temperatures. These wall temperatures agree within ±20°C of the measured wall temperatures.

A displacement based finite element model is developed to predict 3-D thermal stress induced by high temperature and temperature gradient during diesel particulate filter (DPF) regeneration. The temperature field predicted by 3-D conservation of energy is used as input. This finite element model is self-contained and independent of commercial package. It includes functions of meshing body, assembling global stiffness matrix and force vector, solving final equilibrium equations as well as post-processing. This model is validated by commercial software ANSYS and good agreement is observed. Typically, it is the peak temperature rather than temperature gradients that lead to maximum compressive thermal stress in DPF during regeneration. The maximum stress always appears at the channel corner located at the end of DPF. Parametric studies of DPF during loading and regeneration as well as the effect of particulate loading on thermal stress during regeneration are carried out.

Ultrasound is attractive for medical imaging in space because scanners can be small, lightweight, low power, and have minimal electromagnetic emissions. In addition, unlike conventional 2-D ultrasound. 3-D ultrasound allows an operator with no diagnostic skills to collect high-quality scans that can be interpreted by a remote expert. This allows 3-D ultrasound to be used effectively in remote locations. These capabilities are illustrated by the MUSTPAC-1, a portable 3-D ultrasound telemedicine system recently developed for the U.S. military. Design, implementation, and field experiences with the MUSTPAC-1 are discussed, and extensions for use in space are proposed.

A 3-D video sensor designed for in-vehicle operation is presented in this paper. This sensor enables improved occupant protection according to the Federal Motor Vehicle Safety Standard (FMVSS) 208 and beyond. Interior sensors integrated in current occupant protection systems are especially designed for Occupant Classification (OC). However, these interior sensors do not measure the distance between the head and the air bag module. As a result, the air bags deploy independently from the occupants' Out-Of-Position (OOP) status in crash situations. On the contrary, the sensor presented in this paper overcomes this shortcoming by providing dynamic Out-Of-Position Sensing (OOPS) capabilities in addition to occupant classification. The requirements of dynamic OOPS are discussed and an appropriate test device and test procedure are described. Furthermore, the paper presents the sensor principle, the hardware architecture and algorithms for image data processing.

MRO providers are discovering ways to innovate their procedures while remaining viable and profitable through the current downturn in government spending.

The demand for innovative manufacturing technology that produces lighter parts with stronger material grows each day in the competitive aerospace industry. 3-D printing, also known as “additive manufacturing,” is at the center of this innovation.