Search Results

Standard

Aluminum Alloy Extrusions, 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T73511), Solution Heat Treated, Stress Relieved, and Overaged

2024-03-22

CURRENT

AMS4157F

This specification covers an aluminum alloy in the form of extruded bars, rods, wire, shapes, and tubing 5.000 inches (127.00 mm) and under in nominal diameter or least thickness (wall thickness of tubing) (see 8.5).

Technical Paper

Wear Behavior of Hard Ceramic Coatings by Aluminum Oxide– Aluminum Titanate on Magnesium Alloy

2024-02-23

2023-01-5109

However, the coatings substantially improved these values, resulting in hardness measurements of 715 HV and 850 HV, respectively.

Technical Paper

Study of Corrosion Behavior of Hard Anodized Magnesium Alloy by Dow-17 Process

2024-02-23

2023-01-5176

The key parameters of this research work are Coating Thickness, Anodizing Duration, Hard Anodizing Process and Surface Preparations.

Standard

Anodic Treatment of Magnesium Alloys Acid Type, Thin coat

2024-02-16

CURRENT

AMS2479E

This specification establishes the engineering requirements for producing an acid-type, anodic coating on magnesium alloys and the properties of the coating.

Standard

Anodic Treatment of Magnesium Alloys Acid Type, Full Coat

2023-12-13

CURRENT

AMS2478F

This specification establishes the engineering requirements for producing an acid-type, anodic coating on magnesium alloys and the properties of the coating.

Standard

Magnesium Alloy, Plate 4.0Y - 2.25Nd - 0.5Zr (WE43C - T5) Precipitation Heat Treated

2023-12-13

CURRENT

AMS4371C

This specification covers a magnesium alloy in the form of rolled plate from 0.500 up to 6.0 inches (12.7 to 152.4 mm), inclusive (see 8.5).

Standard

Aluminum Alloy, Extruded Profiles (7055-T77511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress Relieved, and Overaged

2023-12-13

CURRENT

AMS4337C

This specification covers an aluminum alloy in the form of extruded profiles (shapes) 0.500 to 1.500 inch (12.7 to 38.1 mm), inclusive, in nominal thickness, and having a maximum cross-sectional area of 20 square inches (129 cm2) and a maximum circle size of 10 inches (254 mm) (see 8.7).

Standard

Brass, Naval, Bars and Rods, 60.5Cu - 38.5Zn - 0.75Sn, Hard Temper (H04)

2023-10-16

CURRENT

AMS4612L

This specification covers a copper alloy (naval brass) in the form of bars and rods.

Standard

Aluminum Alloy, Drawn, Round, Seamless, Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Close Tolerance, Annealed

2023-08-01

CURRENT

AMS4079J

This specification covers an aluminum alloy in the form of drawn, round, seamless tubing with wall thickness of 0.018 to 0.500 inch (0.46 to 12.70 mm), inclusive (see 8.6).

Standard

Plating, Tin-Lead (Electrodeposited)

2023-05-24

CURRENT

AMSP81728C

This specification covers the requirements for electrodeposited tin-lead plating intended for use as a coating for corrosion protection and as a base for soldering.

Standard

Pressure Testing, Gaseous Media Pressure as Specified

2023-05-24

CURRENT

AMS2610

This specification provides requirements and procedures for gas-pressure leak testing of parts.

Standard

Pressure Testing, Hydraulic Pressure as Specified

2023-05-17

CURRENT

AMS2615G

This specification provides requirements and procedures for hydraulic-pressure leak testing of parts.

Standard

Aluminum Alloy, Drawn, Round, Seamless Hydraulic Tubing 2.5Mg - 0.25Cr (5052-O) Annealed

2023-05-10

CURRENT

AMS4071P

This specification covers an aluminum alloy in the form of drawn, round seamless tubing having a wall thickness of 0.010 to 0.450 inch (0.25 to 11.43 mm), inclusive, and nominal outside diameters of 0.125 to 3.000 inch (3.18 to 76.2 mm), inclusive (see 8.5).

Standard

Aluminum Alloy, Extruded Profiles 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated

2023-05-10

CURRENT

AMS4113G

This specification covers an aluminum alloy in the form of extruded profiles such as angles, channels, tees, zees, I-beams, and H-beams.

Standard

Fuse, Current Limiter Type, Aircraft

2023-03-27

CURRENT

AS5372A

This specification covers the requirements for current limiter type fuses for use in aircraft primary electrical power systems conforming to MIL-STD-704. These limiters are suitable for use in AS53731 fuse holders for operation at −54 to 125 °C.

Standard

Aluminum Alloy, Discontinuously Reinforced Hot Isostatically Pressed Shapes 6061B/SiC/40p (3 μm) (T1P)

2023-03-08

CURRENT

AMS4368A

This specification covers discontinuously reinforced aluminum alloy (DRA) metal matrix composites (MMC) made by mechanical alloying of 6061B aluminum powder and SiC particulate, which is then consolidated by Hot Isostatic Pressing (HIP) into shapes between 12 to 100 square inches (0.008 to 0.065 m2), inclusive, cross-section. Tensile property response to heat treatment has been demonstrated on samples of 1 square inch (645 mm2) maximum cross section (see 8.9).

Standard

Aluminum Alloy, Extruded Profiles (7449-T79511) 8.1Zn - 1.8Cu - 2.2Mg - 0.16Zr Solution Heat Treated, Stress Relieved, and Overaged

2023-03-08

CURRENT

AMS4305A

This specification covers an aluminum alloy in the form of extruded profiles 0.500 to 1.750 inches thick (12.70 to 44.20 mm), inclusive, with a maximum cross-sectional area of 20 square inches (129 cm2) and a maximum circle size of 10 inches (254 mm).

Standard

Silver Alloy, Brazing Filler Metal 54Ag - 40Cu - 5.0Zn - 1.0Ni 1325 to 1575 °F (718 to 857 °C) Solidus-Liquidus Range

2023-01-17

CURRENT

AMS4772L

This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips and a viscous mixture (paste) of powder in a suitable binder.

Standard

Electrolytic Treatment for Magnesium Alloys Alkaline Type, Full Coat

2022-11-22

CURRENT

AMS2476D

This specification establishes the engineering requirements for producing anodic coatings on magnesium and magnesium alloys, from an alkaline electrolyte, and the properties of those coatings. ...This specification establishes the engineering requirements for producing anodic coatings on magnesium and magnesium alloys, from an alkaline electrolyte, and the properties of those coatings.

Standard

Aluminum Alloy, Extruded Profiles, 8.9Zn - 2.2Cu - 2.2Mg - 0.15Zr (7136-T74511), Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged

2022-11-02

CURRENT

AMS4367A

This specification covers an aluminum alloy in the form of extruded rods, bars, and profiles (shapes) 0.040 to 4.500 inches (1.02 to 114.30 mm), inclusive, in thickness produced with maximum cross sectional area of 56.1 square inches (36199 mm2) and a maximum circumscribing circle diameter (circle size) of 24.4 inches (620 mm) (see 2.4.1 and 8.6).