Search Results

Classic vehicle production had limitations in bringing the driving commands to the actuators for vehicle motion (engine, steering and braking). Steering columns, hydraulic tubes or steel cables needed to be placed between the driver and actuator. Change began with the introduction of e-gas systems. Mechanical cables were replaced by thin, electric signal wires. The technical solutions and legal standardizations for addressing the steering and braking systems, were not defined at this time. Today, OEMs are starting E/E-Architecture transformations for manifold reasons and now have the chance to remove the long hydraulic tubes for braking and the solid metal columns used for steering. X-by-wire is the way forward and allows for higher Autonomous Driving (AD) levels for automated driving vehicles. This offers new opportunities to design the vehicle in-cabin space. This paper will start with the introduction of x-by-wire technologies.

The lack of inherent security controls makes traditional Controller Area Network (CAN) buses vulnerable to Machine-In-The-Middle (MitM) cybersecurity attacks. Conventional vehicular MitM attacks involve tampering with the hardware to directly manipulate CAN bus traffic.

OBD, J1939 and UDS on CAN / IP), and a glimpse into the near future covering remote, cloud-based diagnostics and cybersecurity threats.

This book, in its second edition, examines the energy sources that play a vital role in society today, as well as those that may be the primary energy sources of tomorrow. From our reliance on fossil fuels to the quest for energy independence, and the environmental issues that follow each decision, this book delves into the most prominent energy issues of our time. Armed with this information, the reader can think critically about the direction they want this world to take. Contents: Brief History of Energy Consumption Fossil Energy - Coal Fossil Energy - Oil and Gas Peak Oil Nuclear Energy Renewable Energy - Solar Energy Renewable Energy - Wind Energy Renewable Energy - Energy from Water Renewable Energy - Bioenergy and Synfuels Energy Carrier, Energy Storage and Hybrid Energy Systems Electricity Generation and Distribution Energy Economics Future Issues - Geopolitics of Energy Future Issues - Energy Forecasts

Access mechanisms to system data and/or control is a primary use case of the hardware protected security environment (hardware protected security environment) during different uses and stages of the system. The hardware protected security environment acts as a gatekeeper for these use cases and not necessarily as the executor of the function. This section is a generalization of such use cases in an attempt to extract common requirements for the hardware protected security environment that enable it to be a gatekeeper. Examples are: Creating a new key fob Re-flashing ECU firmware Reading/exporting PII out of the ECU Using a subscription-based feature Performing some service on an ECU Transferring ownership of the vehicle Some of these examples are discussed later in this section and some have detailed sections of their own. This list is by no means comprehensive.

Rockets re-engineered-a step further into the cosmos Powertrain design for reliability Ice breaker Mazda's Skyactiv-X beats the big companies to market with a promising new engine that marries Otto and Diesel attributes. Advances for off-highway engine design As manufacturers continue to drive out cost and meet a worldwide patchwork of regulatory frameworks, the tools for developing those engines are advancing. From showcase prototypes to advanced analytical techniques, suppliers are helping the cause. Aeroacoustic simulation delivers breakthroughs in aircraft noise reduction Autonomy testing: Simulation to the rescue Autonomous technology development injects new rigors on vehicle-development testing.

Introduction to Managing Energy Data: The Internet of Things (IoT) revolution (eg. the vast spread of smart meters worldwide) is generating massive amounts of energy data, drastically transforming the sector and current energy systems. This digital transformation gives rise to more intelligent ways of managing energy and brings about opportunities for energy companies to improve their business models and services. This course contains a brief introduction to the topics presented in the course, from smart meters and smart metering data to data science.

The comeback car The Cal Poly Pomona FSAE Team implements several measures to help overcome setbacks and achieve a podium finish at Formula SAE Lincoln. Going deep The uBox concept car developed as part of Clemson's Deep Orange program features a uniquely formed roof part. Creating a monster North Dakota State University SAE Clean Snowmobile Challenge team brings to life a war-torn engine pieced together with parts from another.

Annual conference government policy, regulatory makers, automotive industry neutral forum discuss US government regulation, technology, customer acceptance future vehicle design. industry event safety, emission control, fuel efficiency, automated vehicles.

Registration for the Government/Industry Meeting

Registration for the Government/Industry Meeting will be open on September 1, 2023. Please check back soon.

Connected vehicles can provide data from multiple sensors that monitor both the vehicle and the environment through which the vehicle is passing. The data, when shared, can be used to enhance and optimize transportation operations and management—specifically, traffic flow and infrastructure maintenance. This document describes an interface between vehicle and infrastructure for collecting vehicle/probe data. That data may represent a single point in time or may be accumulated over defined periods of time or distance, or may be triggered based on circumstance. The purpose of this document is to define an interoperable means of collecting the vehicle/probe data in support of the use cases defined herein. There are many additional use cases that may be realized based on the interface defined in this document. Note that vehicle diagnostics are not included within the scope of this document, but diagnostics-related features may be added to probe data in a future supplemental document.

This document applies to the development of Plans for integrating and managing COTS assemblies in electronic equipment and Systems for the commercial, military, and space markets; as well as other ADHP markets that wish to use this document. For purposes of this document, COTS assemblies are viewed as electronic assemblies such as printed wiring assemblies, relays, disk drives, LCD matrices, VME circuit cards, servers, printers, laptop computers, etc. There are many ways to categorize COTS assemblies1, including the following spectrum: At one end of the spectrum are COTS assemblies whose design, internal parts2, materials, configuration control, traceability, reliability, and qualification methods are at least partially controlled, or influenced, by ADHP customers (either individually or collectively). An example at this end of the spectrum is a VME circuit card assembly.

The new generation vehicles these days are managed by networked controllers. A large portion of the networks is planned with more security which has recently roused researchers to exhibit various attacks against the system. This paper talks about the liabilities of the Controller Area Network (CAN) inside In-vehicle communication protocol and a few potentials that could take due advantage of it. Moreover, this paper presents a few security measures proposed in the present examination status to defeat the attacks. In any case, the fundamental objective of this paper is to feature a comprehensive methodology known as Intrusion Detection System (IDS), which has been a significant device in getting network data in systems over many years. To the best of our insight, there is no recorded writing on a through outline of IDS execution explicitly in the CAN transport network system.

Clearing the air Sensors, diagnostics and controls advance to help trap emissions. Bringing the heat on cooling technologies Electronic controls, variable-speed fans cool engines, heat aftertreatment systems. 3D printing machines can't be built fast enough In the additive manufacturing world, the costs of components are dropping, the technology is becoming more reliable and parts are fabricated faster, allowing industries beyond aerospace to adopt additive technologies, says Oak Ridge Lab's Ryan Dehoff.

HMIs extend beyond the cab Telematics functions are being integrated into multi-function user interfaces. Standards step forward in design of off-highway electronics Functional safety standards are starting to impact many development projects, while the auto industry's AUTOSAR standard is being deployed to help enable software reuse and simplify designs. Leveraging automotive lightweighting techniques to improve off-highway emissions Where systems engineers can gain efficiencies in off-highway equipment is agnostic, they'll take it anywhere, and so they should, but one of the ways, often underestimated, is through the use of strong and lightweight advanced materials. Waste heat recovery for the long haul A WHR system based on an organic Rankine cycle has been developed for a long-haul Iveco Stralis truck.

Connectivity takes center stage Telematic links have become the norm, helping fleet owners and operators improve efficiency and letting OEMs predict component failures. More power, less noise, fewer emissions These key attributes drive development of new generators both big and small. TARDEC pursues advanced power generation U.S. Army, GM collaborate on fuel-cell-generated electricity to power the vehicle's propulsion system and onboard electronics, while providing off-vehicle power via an Exportable Power Take-Off unit. Developing an alternative engine concept Ricardo's CryoPower engine leverages two unique combustion techniques for reduced emissions and fuel consumption-liquid nitrogen and split combustion. Long-haul trucking and stationary power generation will be the first beneficiaries of the technologies. Technology time-warp The road to autonomous driving has been under construction for decades, as showcased by SAE's Mobility History Committee at the 2018 WCX in Detroit.

Headliners from Las Vegas Big reveals abounded at the triennial CONEXPO trade show. Following are some of the most notable unveilings from the desert. Cat doubles down on diesel with new C13D platform Deere pursues electric construction machines and charging infrastructure JCB debuts clean-sheet hydrogen combustion engine Volvo CE unveils electric asphalt compactor, announces NA arrival of L350H loader Honda reveals next-gen Autonomous Work Vehicle Deere 3D-prints fuel valves for tractors HP's binder jetting technology and GKN's manufacturing expertise helped John Deere realize its first 3D-printed metal part for mass production. Returning to the SAE presidency for 2023 Setting a "prudently aggressive" mindset in advancing SAE's goals in the mobility ecosystem.

Software needs security. That's a consequence of using software to control critical systems. It's difficult because software is inherently a complex artifact, even when the code just consists of a single sequential program in a single programming language, with well-defined inputs and outputs. Of course, actual software rarely if ever has such a simple structure. Security needs software. That's a consequence of the complexity just mentioned. No process can ensure security at scale unless it is automated by using software itself: programming languages, verification tools, software platforms.

This interface document SAE J2286 revises the requirements for file formats as described in SAE J1924. This document describes Interface 1 (I/F 1) in SAE J2214. This document does not imply the use of a specific hardware interface, but may be used with other hardware interfaces such as SAE J1939. The requirements of SAE J2286 supersede the requirements defined by SAE J1924.