Search Results

The efforts of the ISO “Test Variability Task Force” have been aimed at improving the understanding and at reducing brake dynamometer test variability during performance testing. In addition, dynamometer test results have been compared and correlated to vehicle testing. Even though there is already a vast amount of anecdotal evidence confirming the fact that different procedures generate different friction coefficients on the same brake corner, the availability of supporting data to the industry has been elusive up to this point. To overcome this issue, this paper focuses on assessing friction levels, friction coefficient sensitivity, and repeatability under ECE, GB, ISO, JASO, and SAE laboratory friction evaluation tests.

The introduction of MultiAir technology [8] has had a strong impact on engine performance, fuel consumption, emissions and control. This technology, intended at first for gasoline engines and applied only on intake valves, is aiming at the reduction of engine breathing losses and, as a consequence, reduction of pollutant emissions and fuel consumption, together with an improvement of maximum intake efficiency. Further positive effects of MultiAir technology have been a significant improvement of Low End Torque, engine driveability (“fun-to-drive” index) and other operating conditions (e.g. idle control). Current development of MultiAir technology is focusing on a better management of hot EGR (Exhaust Gas Recirculation), still acting only on the intake side, although with specifically designed valve lift profiles. This application of MultiAir technology is pushing gasoline engines towards new levels of performance improvements.

A review of many years of published work has shown that hydrogen embrittlement can occur under rolling contact conditions. Breakdown of lubrication and contamination with water have been cited as the probable sources of atomic hydrogen. In this paper, a unique fracture morphology is identified and the mechanism of the fracture progression from initiation to final catastrophic failure is proposed. Development of beneficial residual compressive stress near the contacting surfaces is one approach used to avoid this type of failure. Several alternative methods capable of developing a more desirable stress distribution will be discussed.

This paper provides a review of the fatigue properties reported in the open literature for die cast magnesium-based alloys. Recently developed fatigue data, in the form of stress versus number of cycles to failure for bending fatigue (R=-1), are presented for die cast AM60B and AZ91D alloy specimens with thicknesses between 1 and 10 mm. The effects of specimen thickness and macrostructural features, such as porosity distributions and surface features (parting line and ejection pin marks), on the fatigue data are discussed.

There is an ongoing interest in biodegradable hydraulic fluids. Biodegradable fluids are often considered to include only vegetable oils, polyol esters and diester base stocks. However, other fluid base stocks including highly refined mineral oils, poly(alpha olefins) and fire-resistant fluids such as water-glycol hydraulic fluids are also biodegradable fluid alternatives. This paper will provide an overview of the international literature on biodegradable fluids, various international testing protocol, fluid base stocks, effect of oxidative stability, material compatibility and pump performance.

A brief overview of the history and scope of the SAE Oil Labeling Assessment Program is presented. Then, the results of analyses on 893 samples of engine oil purchased in the retail market over the first three years of the program, are discussed. All samples were labeled with the API SF or SG Service Category, separately, or in combination with an API “C” category designation. Additionally, 43 engine oil samples found to be questionably labeled, were repurchased and analyzed; these results are included.

Of the many research approaches investigated over the years to measure the lubrication properties of aviation turbine fuels, the Ball-on-Cylinder Lubricity Evaluator (BOCLE) has emerged as the most significant test. BOCLE was originally a lubricant research device modified for low viscosity jet fuel when the Air Force encountered fuel control problems in 1965 with JP-4. It proved to be capable of detecting the presence of additives such as corrosion inhibitors which improve boundary lubrication properties and also the absence of natural lubricity agents in highly refined jet fuel. The Coordinating Research Council carried out several programs to investigate test variables such as cylinder type, humidity control and load. A semi-automated version using Falex test rings has now been commercialized and is being used to test fuels from aircraft experiencing abnormal pump wear and fuel control hang-up.

The aerodynamics of the STOL aircraft can experience significant changes in proximity to the ground. A review of the existing data base and methodologies has been made and the results of that review are presented in this paper. The existing data show that in ground proximity the STOL aircraft will generally experience a reduction in the lift component regardless of the lifting configuration. Those configurations with integrated power and lift systems will have an additional effect of ground induced aerodynamic changes. This paper will discuss the existing data base and the deficiencies of that data base.

This paper presents an overview of the Driver Performance Data Book under preparation by the National Highway Traffic Safety Administration (NHTSA). It includes a brief discussion of the purpose of the Data Book, the restrictions placed on the development effort, and how it is expected that it will be used by Agency personnel and others. Sample pages from the document are reproduced to illustrate the basic format, and the Table of Contents of each section is presented to identify the major topics covered and indicate the number of pages devoted to each.

The purpose of this paper is to survey the adverse environmental impacts resulting from motor vehicles, to review technologies developed to address these problems, and to summarize the current status of pollution control programs around the world.