Search Results

Icing is a major hazard for aviation safety. Over the last decades an additional risk has been identified when flying in clouds with high concentrations of ice-crystals where ice accretion may occur on warm parts of the engine core, resulting in engine incidents such as loss of engine thrust, strong vibrations, blade damage, or even the inability to restart engines. Performing physical engine tests in icing wind tunnels is extremely challenging, therefore, the need for numerical simulation tools able to accurately predict ICI (Ice Crystal Icing) is urgent and paramount for the aeronautics industry, especially regarding the development of new generation engines (UHBR = Ultra High Bypass Ratio, CROR = Counter rotating Open Rotor, ATP = Advanced Turboprop) for which analysis methods largely based on previous engines experience may be less and less applicable. The European research project MUSIC-haic has been conceived to fill this gap and has started in September 2018.

The increasing complexity of distributed embedded systems, as found today in airplanes or cars, becomes more and more a critical cost-factor for their development. Model-based approaches have recently demonstrated their potential for both improving and accelerating (software) development processes. Therefore, in the project DECOS1, which aims at improving system architectures and development of distributed safety-critical embedded systems, an integrated, model-driven tool-chain is established, accompanying the system development process from design to deployment. This paper gives an overview of this tool-chain and outlines important design decisions and features.

In the present work we investigated experimentally and computationally the unsteady flow around a BMW car model including wheels*. This simulation yields mean flow and turbulence fields, enabling the study aerodynamic coefficients (drag and lift coefficients, three-dimensional/spatial wall-pressure distribution) as well as some unsteady flow phenomena in the car wake (analysis of the vortex shedding frequency). Comparisons with experimental findings are presented. The computational approach used is based on solving the complete transient Reynolds-Averaged Navier-Stokes (TRANS) equations. Special attention is devoted to turbulence modelling and the near-wall treatment of turbulence. The flow calculations were performed using a robust, eddy-viscosity-based ζ - ƒ turbulence model in the framework of the elliptic relaxation concept and in conjunction with the universal wall treatment, combining integration up to the wall and wall functions.

For the development of sophisticated digital (e.g., Finite-Element-models like CASIMIR) or physical (e.g.,ASPECT-Dummy) models of the mechanisms of human-seat-interaction it is very important to know the shape of the contact surface between the human buttocks and back and the seat cushion and backrest, respectively. Currently, these surfaces are usually determined by purely experimental procedures, that require complicated and expensive measuring equipment. This paper presents an alternative hybrid approach of standard experimental investigations of the pressure distributions between human body and seat (cushion and backrest) and proceeding numerical simulations with the Finite-Element-Method (FEM). Pressure distributions are measured with standard measuring equipment for individual persons or defined percentile groups. Due to the simplicity of these measurements, they can be performed for a larger number of individuals at low cost.

Future on-board vehicle control systems can be further improved through new types of mechatronic systems. In particular, these systems'' capacities for interaction enhance safety, comfort and economic viability. The Automotive Engineering Department (fzd) of Darmstadt University of Technology is engaged in research of the mechatronic vehicle corner, which consists of three subsystems: sensor tire, electrically actuated wheel brake and smart suspension. By intercommunication of these three systems, the brake controller receives direct, fast and permanent information about dynamic events in the tire contact area provided by the tire sensor as valuable control input. This allows to control operation conditions of each wheel brake. The information provided by the tire sensor for example helps to distinguish between straightline driving and cornering as well as to determine μ-split conditions.

In comparison to other vehicles motorcycles have very special driving characteristics, so the typical use of motorcycles is clearly distinct from the use of passenger cars. At Darmstadt University the riding behavior of motorcyclists has been experimentally investigated [2, 3, 4, 5], especially in order to determine their exhaust and noise emissions in real traffic. The results and the essential differences between motorcycles and cars should be considered in the discussion of testing methods and limiting values, e.g., for exhaust and noise emissions of two-wheelers. This paper presents a comparison between the typical driving performance of motorcycles and passenger cars and contains results of motorcycle exhaust and noise emission measurements in real traffic and in statutory tests. The current legal measuring standards are found not to represent the reality of motorcycle traffic in a sufficient manner.

In the scope of a research collaboration, Continental Teves (formerly ITT Automotive Europe) and Darmstadt University of Technology are developing control strategies for a low-cost Brake-by-Wire system, using no clamping-force or brake-torque sensor as feedback [1]. However, since there is a wide range of variation in the efficiency of the gear units used in electromechanical brakes, this becomes a demanding task. The paper first describes the assembly and operation of Continental Teves' third generation brake actuator, which is still operated using an integrated clamping force sensor [2]. It introduces the development environment of Darmstadt University of Technology, consisting of a brake test stand, a complex brake actuator model, and a simplified brake actuator model.

In the scope of a research collaboration, ITT Automotive Europe and Darmstadt University of Technology are developing control strategies for a low-cost Brake-by-Wire system. However, since there is a wide range of variation in the efficiency of the gear units used in electromechanical brakes, this becomes a demanding task. The paper first describes the assembly and operation of ITT's early generation brake actuator. It introduces a model of the electromechanical brake with its structure and subsystems as a major tool in the development process. A detailed analysis of the signals, already available from the brake and the vehicle, is discussed for their advantages and disadvantages with regard to a possible use in the controller design. Different approaches for clamping-force, peripheral-force and brake-torque sensing are compared. An integrated clamping force sensor for feedback control of prototype actuators was developed.

Faced with the need to reduce development time and cost, the hardware-in-the-loop (HIL) simulation increasingly proves to be an efficient tool in the automotive industry. It offers the possibility to investigate new engine control systems with fewer expensive engine dynamometer experiments and test drives. In the scope of a research collaboration, Daimler Benz and Darmstadt University of Technology are developing a hardware-in-the loop simulator for the investigation of the electronic engine management of the new Mercedes Benz truck engine series 500 and 900. This paper first describes the necessary models for real-time simulation of the subsystems Diesel engine, turbo charger and vehicle. Then the setup of the simulator test bench is introduced and the performance of the simulator is demonstrated by several experimental results.