Search Results

To meet stringent emissions regulations, filtration devices are often used in engine exhaust systems to reduce particulate mass (PM) and particulate number (PN). Diesel particulate filters (DPFs) are a well-established means of reducing PM from diesel engines to meet emissions regulations. New emissions regulations will most likely require a similar technology on gasoline engines with direct injection, gasoline particulate filters (GPFs). Due to differences in the exhaust and particulate characteristics, the design and operation of GPFs and DPFs differ. In a DPF filtration is dominated by the buildup of a soot cake. Whereas in a GPF, much of the soot is trapped inside the porous substrate, or filter wall, where deep-bed filtration is dominant. Thus, an accurate model describing the porous filtration properties of GPF substrates is desired. The pore filtration model (PFM) was developed to more accurately model the deep-bed filtration process that occurs in a GPF.

Modeling ignition kernel development in spark ignition engines is crucial to capturing the sources of cyclic variability, both with RANS and LES simulations. Appropriate kernel modeling must ensure that energy transfer from the electrodes to the gas phase has the correct timing, rate and locations, until the flame surface is large enough to be represented on the mesh by the G-Equation level-set method. However, in most kernel models, geometric details driving kernel growth are missing: either because it is described as Lagrangian particles, or because its development is simplified, i.e., down to multiple spherical flames. This paper covers the geometric aspects of kernel development, which makes up the core of a Triangulated Lagrangian Ignition Kernel model. One (or multiple, if it restrikes) spark channel is initialized as a one-dimensional Lagrangian particle thread.

A novel 2-zone combustion chamber concept (patent pending) was developed using multi-dimensional modeling. At minimum volume, an axial projection in the piston divides the volume into distinct zones joined by a communication channel. The projection provides a means to control the mixture formation and combustion phasing within each zone. The novel combustion system was applied to reactivity controlled compression ignition (RCCI) combustion in both light-duty and heavy-duty diesel engines. Results from the study of an 8.8 bar BMEP, 2600 RPM operating condition are presented for the light-duty engine. The results from the heavy-duty engine are at an 18.1 bar BMEP, 1200 RPM operating condition. The effect of several major design features were investigated including the volume split between the inner and outer combustion chamber volumes, the clearance (squish) height, and the top ring land (crevice) volume.

While Low Temperature Combustion (LTC) strategies such as Reactivity Controlled Compression Ignition (RCCI) exhibit high thermal efficiency and produce low NOx and soot emissions, low load operation is still a significant challenge due to high unburnt hydrocarbon (UHC) and carbon monoxide (CO) emissions, which occur as a result of poor combustion efficiencies at these operating points. Furthermore, the exhaust gas temperatures are insufficient to light-off the Diesel Oxidation Catalyst (DOC), thereby resulting in poor UHC and CO conversion efficiencies by the aftertreatment system. To achieve exhaust gas temperature values sufficient for DOC light-off, combustion can be appropriately phased by changing the ratio of gasoline to diesel in the cylinder, or by burning additional fuel injected during the expansion stroke through post-injection.

The SCR Filter simultaneously reduces NOx and Particle Matter (PM) in the exhaust and is considered an effective way to meet emission regulations. By combining the function of a Diesel Particulate Filtration (DPF) and a Selective Catalytic Reduction (SCR), the SCR Filter reduces the complexity and cost of aftertreatment systems in diesel vehicles. Moreover, it provides an effective reaction surface and potentially reduces backpressure by combining two devices into one. However, unlike traditional flow through type SCR, the deNOx reactions in the SCR Filter can be affected by the particulate filtration and regeneration process. Additionally, soot oxidation can be affected by the deNOx process. A 1-D kinetic model for integrated DPF and NH3-SCR system over Cu-zeolite catalysts was developed and validated with experimental data in previous work[1].

Homogeneous low temperature combustion is believed to be a promising approach to resolve the conflict of goals between high efficiency and low exhaust emissions. Disadvantageously for this kind of combustion, the whole process depends on chemical kinetics and thus is hard to control. Reactivity controlled combustion can help to overcome this difficulty. In the so-called RCCI (reactivity controlled compression ignition) combustion concept a small amount of pilot diesel that is injected directly into the combustion chamber ignites a highly diluted gasoline-air mixture. As the gasoline does not ignite without the diesel, the pilot injection timing and the ratio between diesel and gasoline can be used to control the combustion process. A phenomenological multi-zone model to predict RCCI combustion has been developed and validated against experimental and 3D-CFD data. The model captures the main physics governing ignition and combustion.

A Three-Way Catalyst (TWC) model with global TWC kinetics for lean burn DISI engines were developed and validated. The model incorporates kinetics of hydrocarbons and carbon monoxide oxidations, NOx reduction, water-gas and steam reforming and oxygen storage. Ammonia (NH₃) and new nitrous oxide (N₂O) kinetics were added into the model to study NH₃ and N₂O formation in TWC systems. The model was validated over a wide range of engine operating conditions using various types of experimental data from a lean burn automotive SIDI engine. First, well-controlled time-resolved steady state data were used for calibration and initial model tests. In these steady state operations, the engine was switched between lean and rich conditions for NOx emission control. Then, the model was further validated using a large set of time-averaged steady state data. Temperature dependencies of NH₃ and N₂O kinetics in the TWC model were examined and well captured by the model.

A fundamentally based quasi-dimensional NOx emission model for spark ignition direct injection (SIDI) gasoline engines was developed. The NOx model consists of a chemical mechanism and three sub-models. The classical extended Zeldovich mechanism and N₂O pathway for NOx formation mechanism were employed as the chemical mechanism in the model. A characteristic time model for the radical species H, O and OH was incorporated to account for non-equilibrium of radical species during combustion. A model of homogeneity which correlates fundamental dimensionless numbers and mixing time was developed to model the air-fuel mixing and inhomogeneity of the charge. Since temperature has a dominant effect on NOx emission, a flame temperature correlation was developed to model the flame temperature during the combustion for NOx calculation. Measured NOx emission data from a single-cylinder SIDI research engine at different operating conditions was used to validate the NOx model.

Numerical investigation is carried out to explore various strategies of combustion mode switching in a diesel engine operating at high power. Numerical results are compared with high power single cylinder (CAT 3401E) experiments for combustion phasing and emission characteristics. In this study CFD calculations are carried out using the KIVA CFD code with Large Eddy Simulation turbulence model and Direct Chemistry Solver sub-models. The advanced turbulence and combustion sub-models enabled more realistic visualization of the effects of single-cycle mode switching on in-cylinder flow structures, fuel-air mixing behavior and combustion phasing. Two circumstances of mode switch are presented in this study. Mode switches are performed from traditional High Temperature Combustion to early injection PCCI combustion and vice versa. In this investigation several aspects of combustion control are investigated.

DPF regenerations involve a trade-off between fuel economy and DPF durability. High temperature regenerations of DPFs have fewer fuel penalties but simultaneously tend to give higher substrate temperatures, which can reduce thermal reliability. In order to weaken the trade-off, the integrated system-level model [1,2,3,4] is used to conduct optimization studies and explore novel regeneration strategies for DPF aftertreatment devices. The integrated model developed in the Engine Research Center (ERC) includes sub-models for engines, emissions, aftertreatment devices and controllers. Based on the engine and regeneration fuel economy, multiple and single cycle regeneration tests are performed and analyzed. The optimal soot loadings to initiate and terminate regenerations are discussed. A pulsed regeneration strategy, which is characterized by injecting multiple pulses of fuel (upstream of a DOC) during regenerations, is investigated.

Numerical investigation is carried out in order to explore diesel combustion using advanced turbulence and combustion models. Turbulence is modeled by one-equation non-viscosity dynamic structure Large Eddy Simulation (LES) model. Sub-grid fuel-air mixing is calculated using a dynamic scale similarity sub-grid scalar dissipation model to represent the local state of combustion. Fuel-air mixing time scale is used in order to determine the local in-homogeneity and rate of mixing of fuel and air. Diesel combustion is studied and compared with experimental results for high power diesel engine setup at different conditions representing both low temperature combustion and traditional high temperature combustion regimes. Further studies are carried out in diesel engine to investigate in-cylinder fuel air mixing and the onset of ignition.

Diesel particulate samples were collected from a light duty engine operated at a single speed-load point with a range of biodiesel and conventional fuel blends. The oxidation reactivity of the samples was characterized in a laboratory reactor, and BET surface area measurements were made at several points during oxidation of the fixed carbon component of both types of particulate. The fixed carbon component of biodiesel particulate has a significantly higher surface area for the initial stages of oxidation, but the surface areas for the two particulates become similar as fixed carbon oxidation proceeds beyond 40%. When fixed carbon oxidation rates are normalized to total surface area, it is possible to describe the oxidation rates of the fixed carbon portion of both types of particulates with a single set of Arrhenius parameters. The measured surface area evolution during particle oxidation was found to be inconsistent with shrinking sphere oxidation.

System-level models containing engine model, emission models, and aftertreatment device models have been developed. All the sub-models have been developed separately and come from a variety of different sources. A new phenomenological CO model recently has been coupled into the previous integrated model. The emission models, including PM (particulate matter), NOx, and CO are also calibrated from experimental data. Some modification has been added to improve the integrated model and accept different aftertreatment device models for future work. The objective of this work is to study the DPF (Diesel Particulate Filter) regeneration during transient operating conditions using the integrated model. The integrated system-level model is used to studying the dynamic performance between engine and aftertreatment system. In this study, the calibrated emission models are validated at transient operating conditions.

This work integrated a CA10 (crank angle at 10% heat release) controller into an integrated engine, emissions and aftertreatment model platform. Two CA10 phasing targets were chosen to analyze how advancing (or retarding) the target combustion phasing (CA10) affect the formation of NO and CO. The effect of intake valve closure (IVC) timing, which is the control mechanism for maintaining the target combustion phasing, on the cylinder trapped mass, and hence the charge temperature after compression is detailed. Finally, the relation between combustion phasing and the blow-down process leading to the exhaust process is discussed. Retarding the target combustion phasing by two degrees saw a 330 K drop in compressed charge temperature and a quadrupled reduction of peak NO emitted. Peak NO₂ emission reduced three times on account of the same. However, an increase in CO emission was observed when the combustion phasing was advanced.

Diesel engine combustion is simulated using Large Eddy Simulation (LES) with a multi-mode combustion (MMC) model. The MMC model is based on the combination of chemical kinetics, chemical equilibrium, and quasi-steady flamelet calculations in different local combustion regimes. The local combustion regime is identified by two combustion indices based on the local temperature and the extent of mixture homogeneity. The LES turbulence model uses the dynamic structure model (DSM) for sub-grid stresses. A new spray model in the LES context is used, and the Reynolds-averaged Navier-Stokes (RANS) based wall model is retained with the LES derived scales. These models are incorporated in the KIVA3V-ERC-Release 2 code for engine combustion simulations. A wide range of diesel engine operating conditions were chosen to validate the combustion model.

This article presents nondestructive neutron computed tomography (nCT) measurements of Diesel Particulate Filters (DPFs) as a method to measure ash and soot loading in the filters. Uncatalyzed and unwashcoated 200cpsi cordierite DPFs exposed to 100% biodiesel (B100) exhaust and conventional ultra low sulfur 2007 certification diesel (ULSD) exhaust at one speed-load point (1500 rpm, 2.6 bar BMEP) are compared to a brand new (never exposed) filter. Precise structural information about the substrate as well as an attempt to quantify soot and ash loading in the channel of the DPF illustrates the potential strength of the neutron imaging technique.

Two different types of mesh used for diesel combustion with the KIVA-4 code are compared. One is a well established conventional KIVA-3 type polar mesh. The other is a non-polar mesh with uniform size throughout the piston bowl so as to reduce the number of cells and to improve the quality of the cell shapes around the cylinder axis which can contain many fuel droplets that affect prediction accuracy and the computational time. This mesh is specialized for the KIVA-4 code which employs an unstructured mesh. To prevent dramatic changes in spray penetration caused by the difference in cell size between the two types of mesh, a recently developed spray model which reduces mesh dependency of the droplet behavior has been implemented. For the ignition and combustion models, the Shell model and characteristic time combustion (CTC) model are employed.

A kinetic carbon monoxide (CO) emission model is developed to simulate engine out CO emissions for conventional diesel combustion. The model also incorporates physics governing CO emissions for low temperature combustion (LTC). The emission model will be used in an integrated system level model to simulate the operation and interaction of conventional and low temperature diesel combustion with aftertreatment devices. The Integrated System Model consists of component models for the diesel engine, engine-out emissions (such as NOx and Particulate Matter), and aftertreatment devices (such as DOC and DPF). The addition of CO emissions model will enhance the capability of the Integrated System Model to predict major emission species, especially for low temperature combustion. In this work a CO emission model is developed based on a two-step global kinetic mechanism [8].

System level modeling was used to develop a suitable control strategy for Diesel Homogeneous Charge Compression Ignition (HCCI) transient operation. Intake temperature and pressure, engine speed, engine load, cylinder wall temperature, exhaust gas recirculation, etc. all significantly affect combustion phasing generating a scenario where simple ECU mapping techniques prove inadequate. Two-stage fuels such as diesel fuel pose additional challenges for accurate combustion control. Low-temperature cool-flame chemical heat release can significantly alter the thermodynamic state of the trapped gaseous mixture and hence combustion phasing. Operator and environmentally induced transients can rapidly alter combustion phasing parameters suggesting a need for model-based control. A model-based control strategy featuring the identified essential physics has been developed to control diesel HCCI combustion phasing through transient operation.

An integrated system model containing sub-models for a multi-cylinder diesel engine, NOx and soot(PM) emissions, diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) has been developed to simulate the engine and aftertreatment systems at transient engine operating conditions. The objective of this work is two-fold; ensure correct implementation of the integrated system level model and apply the integrated model to understand the fuel economy trade-off for various DPF regeneration strategies. The current study focuses on a 1.9L turbocharged diesel engine and its exhaust system. The engine model was built in GT-Power and validated against experimental data at full-load conditions. The DPF model is calibrated for the current engine application by matching the clean DPF pressure drop for different mass flow rates. Load, boost pressure, speed and EGR controllers are tuned and linked with the current engine model.