Search Results

The Direct Numerical Simulation (DNS) approach to solving the fundamental transport equations down to the smallest scales of motion is favorable should the requirement be a truly predictive solution of fluid dynamic problems, but the simulation run times are unacceptable for most practical industrial applications. Despite the steadily increasing computational capabilities, Reynolds Averaged Navier-Stokes (RANS) based frameworks remain the most commercially viable option for high volume sectors, like automotive. The sub models within RANS simplify the description of key physical phenomena and include several numerical constants. These so-called “tuning constants” introduce multivariable dependencies that are almost impossible to untangle with local sensitivity studies.

The conventional Diesel cycles engine is now approaching the practical limits of efficiency. The recuperated split cycle engine is an alternative cycle with the potential to achieve higher efficiencies than could be achieved using a conventional engine cycle. In a split cycle engine, the compression and combustion strokes are performed in separate chambers. This enables direct cooling of the compression cylinder reducing compression work, intra cycle heat recovery and low heat rejection expansion. Previously reported analysis has shown that brake efficiencies approaching 60% are attainable, representing a 33% improvement over current advanced heavy duty diesel engine. However, the achievement of complete, stable, compression ignited combustion has remained elusive to date.

Diesel fuel injection pressures have increased steadily on heavy duty engines over the last twenty years and pressures as high as 300MPa are now possible. This was driven by the need to control toxic exhaust emissions, in particular particulate emissions using advanced in-cylinder combustion strategies. With the introduction of efficient aftertreatment systems for both particulate and NOx emissions control there is less demand for in-cylinder emissions control especially considering the drive for improved fuel economy. In this paper we consider the benefit of high fuel injection pressure for a number of emissions control strategies with different balances of in-cylinder and exhaust aftertreatment emissions control. A test program was undertaken on a single cylinder heavy duty research engine installed at the University of Brighton, in collaboration with Ricardo.

Concerns over the impact of road transport emissions on the climate have led to increased focus on how CO2 emissions could be reduced from the sector. This is of particular concern in the commercial vehicle sector, where engine downsizing and electrification have limited benefit due to the vehicle duty cycle. In this paper, we present results from an experimental program to investigate the impact of dual fueling a heavy duty engine on hydrogen and diesel. Hydrogen is potentially a zero carbon fuel, if manufactured from renewable energy but could also be manufactured on the vehicle through steam reformation of part of the liquid fuel. This opens a novel pathway for the recovery of waste heat from the exhaust system through the endothermic steam reformation process, improving the overall system efficiency. For these concepts to be viable, it is essential the dual fueled combustion system is both thermally efficient, and does not increase toxic emissions such as NOx.

This paper presents the summary of the development of a two-phase spray model of a hollow-cone fuel injector commonly applied to spray-guided, gasoline direct injection, (SGDI) engines. The model was simulated using the Ricardo VECTIS CFD code and takes into account the physical and chemical effects of oxygenated fuel blends (flexfuels). The characteristics of the fuel sprays at typical gasoline part-load conditions, identified in a parallel study, were of particular interest. An injection duration of 0.3 ms was chosen which represented a stratified charge, unthrottled, part-load operating condition in a spray guided GDI engine with a piezoelectric fuel injector and a fuel injection pressure of 200 bar gauge. In the first instance, the spray model was validated against data recorded in a constant volume spray chamber. Secondly, the robustness of the model was tested against data measured in an optically-accessed engine.

Compared to conventional homogeneous direct injection or port-fuel injected engines, the second generation, spray guided, direct injection engine (SGDI) has the potential for significantly improved fuel economy during part load stratified charge operation. Multiple fuel injection strategies can be utilised to increase the unthrottled operating range, leading to further improvements in fuel economy. However, careful optimisation of these strategies is essential to ensure that benefits are maintained whilst further minimising emissions within combustion stability limits and consumer driveability demands. The effects of multiple injection strategies upon fuel consumption, emissions and combustion stability were investigated in a single cylinder Ricardo Hydra engine with a spray guided combustion system. An outwardly opening piezoelectric actuated injector was employed. The fuel injection strategy utilised up to five injections per engine cycle.