Search Results

A 2-stroke combustion cycle has higher power output densities compared to a 4-stroke cycle counterpart. The modern down-sized 4-stroke engine design can greatly benefit from this attribute of the 2-stroke cycle. By using appropriate variable valvetrain, boosting, and direct fuel injection systems, both cycles can be feasibly implemented on the same engine platform. In this research study, two valve strategies for achieving a two-stroke cycle in a four-stroke engine have been studied. The first strategy is based on balanced compression and expansion strokes, while the gas exchange is done through two different strokes. The second approach is a novel 2-stroke combustion strategy - here referred to as 2-stroke Miller - which maintains the expansion as achieved in a 4-stroke cycle but suppresses the gas exchange into the compression stroke.

Homogenous Charge Compression Ignition (HCCI) combustion phasing and stability provides a challenging control problem over conventional combustion technologies of Spark Ignition (SI) and Compression Ignition (CI). Due to the auto ignition nature of the HCCI combustion there are no direct methods for actuation, the combustion and the phasing relies on indirect methods. This in itself creates a nonlinear dynamic problem between the relationships of control actuators and the combustion behavior. In order to control the process, an accurate feedback signal is necessary to determine the state of the actual combustion process. Ideally to ensure that combustion remains stable and phased correctly an in-cylinder feedback of each cylinder for multi cylinder engines would be preferable. Feedback has been seen in studies using piezoelectric pressure sensors for visually monitoring the pressure in the combustion chamber. This is expensive and requires redesign of the combustion chamber.

The Otto cycle delivers theoretical maximum thermal efficiency. The traditional design of internal combustion engines using a simple slide-crank mechanism gives no time for a constant volume combustion which significantly reduces the cycle efficiency. In this study, using a high torque, high bandwidth, permanent magnet electric drive system attached to the crankshaft, variable angular velocities of the engine crankshaft were implemented. The system enabled reductions in piston velocity around the top dead centre region to a fraction of its value at constant crankshaft angular velocity typical in conventional engines. A quasi-constant volume combustion has thus been successfully achieved, leading to improvements in engine fuel consumption and power output which are discussed in detail.

Over the past few decades, Homogeneous Charge Compression Ignition (HCCI) or Controlled Auto-Ignition (CAI) if it is fuelled with gasoline type of fuels has shown its potential to overcome the limitations and environmental issue concerns of the Spark Ignition (SI) and Compression Ignition (CI) engines. However, controlling the ignition timing of a CAI engine over a wide range of speeds and loads is challenging. Combustion in CAI is affected by a number of factors; the local temperature, the local composition of the air/fuel mixture, time and to a lesser degree the pressure. The in-cylinder engine charge flow fields have significant influences on these factors, especially the local gas properties, which leads to the influences towards the CAI combustion. In this study, such influences were investigated using a Computational Fluid Dynamics (CFD) engine simulation package fitted with a real optical research engine geometry.

Closed-loop electronic control is a proven and efficient way to optimize spark ignition engine performance and to control pollutant emissions. In-cylinder pressure sensors provide accurate information on the quality of combustion. The conductivity of combustion flames can alternatively be used as a measure of combustion quality through ion-current measurements. In this paper, combustion diagnostics through ion-current sensing are studied. A single cylinder research engine was used to investigate the effects of misfire, ignition timing, air to fuel ratio, compression ratio, speed and load on the ion-current signal. The ion-current signal was obtained via one, or both, of two additional, remote in-cylinder ion sensors (rather than by via the firing spark plug, as is usually the case). The ion-current signals obtained from a single remote sensor, and then the two remote sensors are compared.

The Homogeneous Charge Compression Ignition (HCCI) engine combustion uses heat energy from trapped exhaust gases enhanced by the piston compression heating to auto ignite a premixed air/gasoline mixture. As the HCCI combustion is controlled by the charge temperature, composition and pressure, it therefore, prevents the use of a direct control mechanism such as in the spark and diesel combustion. Using a large amount of trapped residual gas (TRG), is seen as one of the ways to achieve and control HCCI in a certain operating range. By varying the amount of TRG in the fresh air/fuel mixture (inside the cylinder), the charge mixture temperature, composition and pressure can be controlled and hence, the auto ignition timing and heat release rate. The controlled auto ignition (HCCI) engine concept has the potential to be highly efficient and to produce low NOx, carbon dioxide and particulate matter emissions.

Homogeneous Charge Compression Ignition (HCCI) engine concept has the potential to be high efficient and to produce low NOx and particulate matter emissions. However, the problem of controlling the combustion over the entire load/speed range limits its practical application. The HCCI combustion is controlled by chemical kinetics of the charge mixture, with no influence of the flame diffusion or turbulent propagation. Therefore, to achieve a successful control of the HCCI process, the composition, temperature and pressure of the charge mixture at IVC point have to be controlled. The use of the variable valve timing strategy that enables quick changes in the amount of trapped hot exhaust gases shows the potential for the control of the HCCI combustion.

Valve timing strategies aimed at producing internal exhaust gas re-circulation in a conventional spark ignition, SI, engine have recently demonstrated the ability to initiate controlled auto-ignition, CAI. Essentially the exhaust valves close early, to trap a quantity of hot exhaust gases in-cylinder, and the fresh air-fuel charge is induced late into the cylinder and then mixing takes place. As a logical first step to understanding the fluid mechanics, the effects of the standard and modified valve timings on the in-cylinder flow fields under motored conditions were investigated. Laser Doppler anemometry has been applied to an optical engine that replicates the engine geometry and different valve cam timings. The cycle averaged time history mean and RMS velocity profiles for the axial and radial velocity components in three axial planes were measured throughout the inlet and compression stroke.

Controlled Auto Ignition (CAI) uses compression heat to auto ignite a homogeneous air/fuel mixture. Using internal exhaust gas recirculation (IEGR) as an indirect control method, CAI offers superior fuel economy and pollutant emission reductions. Practically, this can readily be achieved by a method of early exhaust valve closure and late inlet valve opening to trap exhaust gas residuals within the cylinder from one cycle to the next. In order to understand the combustion mechanism, we did a comprehensive investigation on CAI fuelled with iso-octane. Test data was gathered from a single cylinder research engine equipped with Lotus' Research Active Valve Train (AVT) System, and the modelling study was based on detailed chemical kinetics. It was found that CAI can only occur when the thermal energy of the engine charge, which is a mixture of air / fuel and IEGR, reaches a certain level.

Controlled auto ignition (CAI) is a form of combustion which uses an auto-ignited homogeneous air/fuel mixture but is controlled (or moderated) by regulating the quantity of internal exhaust gas residuals. In this paper, using a fully variable valve train and a newly developed exhaust valve control strategy, we substituted EGR with hot nitrogen or hot air. We found that the internal exhaust gas residuals have both thermal and chemical effects on CAI combustion. To investigate the thermal effect, nitrogen was used as it is a chemically inert gas. Although its temperature was raised to that of the internal exhaust gas residuals during testing, CAI combustion could not be promoted without assistance from a spark in a form of hybrid CAI, thus indicating that exhaust gas residuals have a chemical effect as well.

Engines with controlled auto-ignition (CAI) combustion offer a number of benefits over conventional spark ignited (SI) and compression ignited (CI) engines, such as much lower NOx emission due to its relatively low combustion temperature, negligible cycle-to-cycle variation due to its self-ignition nature, higher combustion efficiency at part load than its SI counterpart, and low soot emissions since a homogeneous lean air/fuel mixture is being employed. Unlike conventional SI and CI engines, where combustion is directly controlled by the engine management system, the combustion in CAI engines is controlled by chemical kinetics only. Over the past two decades, a number of technologies have been developed to initiate such combustion on both 2 and 4-stroke engines with various fuels, but none of them could maintain the combustion over the wide engine operation range. Remaining problems include control of ignition timing and the heat release rate over the entire engine operation range.