Search Results

This SAE Recommended Practice describes the test procedures for conducting free motion headform testing of heavy truck cab interior surfaces and components. A description of the test set-up, instrumentation, impact configuration, target locations, and data reduction is included.

This SAE Recommended Practice provides procedures and methods for testing service, spring applied parking, and combination brake actuators with respect to durability, function, and environmental performance. A minimum of six test units designated A, B, C, D, E, and F are to be used to perform all tests per 1.1 and 1.2.

This Recommended Practice is derived from OEM and tier-1 laboratory tests and applies to two-axle multipurpose passenger vehicles, or trucks with a GVWR above 4536 kg (10 000 pounds) equipped with hydraulic disc or drum service brakes. Before conducting testing for a specific brake sizes or under specific test conditions, review, agree upon, and document with the test requestor any deviations from the test procedure. Also, the applicable criteria for the final test results and wear rates deemed as significantly different require definition, assessment, and proper documentation; especially as this will determine whether or not Method B testing is needed. This Recommended Practice does not evaluate or quantify other brake system characteristics such as performance, noise, judder, ABS performance, or braking under extreme temperatures or speeds. Minimum performance requirements are not part of this recommended practice.

This SAE Recommended Practice establishes methods to determine grade parking performance with respect to:a. Ability of the parking brake system to lock the braked wheels.b. The trailer holding or sliding on the grade, fully loaded, or unloaded.c. Applied manual effort.d. Unburnished or burnished brake lining friction conditions.e. Down and upgrade directions.

This SAE Recommended Practice establishes a method of evaluating the structural integrity of the parking brake system of all new trucks, buses, and combination vehicles designed for roadway use in the following classifications: TRACTOR, TRAILER, TRUCK, AND BUS: over 4500 kg (10 000 lb) GVWR.

This SAE Standard applies to all forestry machines exposed to the hazard of objects penetrating the front of the operator station (other than the roof). This would include:

This SAE Recommended Practice (RP) establishes uniform vehicle level simulation procedure for Forward Collision Avoidance and Mitigation (FCAM) systems (also identified as Automatic Emergency Braking (AEB) systems) used in highway commercial vehicles and coaches greater than 4535 Kg (10,000 lb.) GVWR. For Hardware-in-the-loop implementation of the recommended practice, the ESC system will be part of the test. This RP does not apply to trailers, dollies, etc. and does not intend to exclude any particular system or sensor technology. These FCAM systems utilize various methodologies to identify, track and communicate data to the operator and vehicle systems to warn, intervene and/or mitigate in the longitudinal control of the vehicle.

This SAE Recommended Practice identifies the minimum truck tractor electrical power output of the stop lamp and ABS (antilock brake system) circuits measured at the primary SAE J560 tractor trailer interface connector(s).

SAE J1978-1 specifies a complementary set of functions to be provided by an OBD-II scan tool. These functions provide complete, efficient, and safe access to all regulated OBD (on-board diagnostic) services on any vehicle which complies to SAE J1978-1 The SAE J1978-1 content of this document is intended to satisfy the requirements of an OBD-II scan tool as required by current U.S. on-board diagnostic (OBD) regulations. This document specifies: A means of establishing communications between an OBD-equipped vehicle and an OBD-II scan tool. A set of diagnostic services to be provided by an OBD-II scan tool in order to exercise the services defined in SAE J1979 and SAE J1979-2. The presentation of the SAE J1978 document family, where SAE J1978-1 covers first generation protocol functionality defined in SAE J1979, and SAE J1978-2 covers second generation protocol functionality defined in SAE J1979-2.

The SAE Recommended Practice establishes minimum performance requirements and related uniform laboratory test procedures for evaluating lateral (curb) impact collision resistance of all wheels intended for use on passenger cars and light trucks.

This SAE Recommended Practice is intended to describe a procedure for rating the size of single-stage reciprocating air compressors. It describes the conditions that can be used for testing and it defines a standardized rating expressed in SLPM (SCFM).

This SAE Recommended Practice presents requirements for the structural integrity of the brake system of all new trucks, buses, and combinations of vehicles designed for roadway use and falling into the following classifications: a Truck and Bus—Over 4500 kg (10 000 lb) GVWR b Combination Vehicles—Towing vehicle over 4500 kg (10 000 lb) GVWR The requirements are based on data obtained from SAE J294.

Provide previous stop light activation research into single document for future reference.Relevant documents and interpretations noted in Table 1.

This SAE document defines a recommended practice for implementing circuit identification for electrical power and signal distribution systems of the Class 8 trucks and tractors. This document provides a description of a supplemental circuit identifier that shall be utilized in conjunction with the original equipment manufacturer’s primary circuit identification as used in wire harnesses but does not include electrical or electronic devices which have pigtails. The supplemental circuit identifier is cross-referenced to a specified subsystem of the power and signal distribution system identified in Section 5.

The SAE J1939 communications network is developed for use in heavy-duty environments and suitable for horizontally integrated vehicle industries. The SAE J1939 communications network is applicable for light-duty, medium-duty, and heavy duty vehicles used on-road or off-road, and for appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include, but are not limited to, on-highway and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements.SAE J1939-71 is the SAE J1939 reference document for the conventions and notations used to specify the parameter (SP) placement in PG data, the conventions for ASCII parameters, and conventions for PG transmission rates. This document previously contained the majority of the SAE J1939 OSI application layer data parameters and messages for information exchange between the ECU applications connected to the SAE J1939 communications network.

This SAE recommended practice defines the system and component functions, measurement metrics, testing methodologies for evaluating the functionality and performance of tire pressure systems for use on trailers under 26,000lbs. GVWR within the known operating environments. This document is applicable to all towed trailers under 26,000lbs. GVWR. Examples of towed trailers are recreational vehicle travel trailers and fifth wheels, utility trailers, cargo trailers, livestock trailers, flatbed trailers, boat trailers, and snowmobile trailers. These trailers can be equipped with 1,2 or 3 axles with each axle supporting either 2 or 4 tires. These systems are recommended to address all tires in service as originally installed on a trailer by the OEM. This Recommended Practice can also be applied to external TPMS that also cover tow vehicles and trailers simultaneously. This document will focus on tire pressure systems of the monitoring type.

This SAE Recommended Practice pertains to liquid level determination for any fluid compartment of off-road work machines as defined in SAE J1116 and ISO 6165.

This document is intended to supplement the SAE J1939 documents by offering the SAE J1939 information in a form that can be sorted and search for easier use.

This document will apply to the most common applications of electric motors, used for activating all-wheel drive (AWD) and four-wheel drive (4WD) disconnect systems as used in passenger (car and light truck) vehicles. The standard will provide consistent definition, terminology, tests, and reporting methods.

The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road as well as appropriate stationary applications which use vehicle derived components (e.g. generator sets). Vehicles of interest include, but are not limited to, on- and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements.

The purpose of these documents is to provide an open interconnect system for electronic systems. It is the intention of these documents to allow Electronic Control Units to communicate with each other by providing a standard architecture.

This particular document, SAE J1939-74, describes the message structure for a set of messages which enable the user to determine and announce to others on the network, the parameter placement within a particular message from the special set of messages defined within this document.