Search Results

This paper is on the design of a steer-by-wire system for a light commercial vehicle. A hardware-in-the-loop simulation test rig with the actual rack and pinion mechanism of the light commercial vehicle under study was built for this purpose. The steer-by-wire actuator can be placed on either the second pinion, the first pinion or both in the double pinion steering test system used. The hardware and geometry of the steering test rig are identical to the implementation of the steering system in the test vehicle. Unnecessary and expensive road testing is avoided with this approach as most problems are identified and solved in the hardware-in-the-loop simulation phase conducted in the laboratory where the steering subsystem and its controller exist as hardware and the rest of the vehicle exist as a software model running in real time. Hardware-in-the-loop simulation results show the effectiveness of the proposed controller design in tracking desired steering dynamics.

This paper presents the development of a transient active control (TABC) system for the Ford Transit Connect light commercial vehicle using semi active suspensions. The control objective is to improve the ride comfort and road holding together with achieving roll and pitch stability using four semi active suspension dampers, hence called transient active body control. Semi-active control algorithms such as sky-hook, ground-hook and hybrid are applied to each suspension while the roll and pitch stabilizing controllers are designed separately and interfere with the local semi-active controllers through a supervisory control algorithm, if necessary. Simulation and experimental results are presented to demonstrate the effectiveness of the proposed technique.

There is an increasing trend in the worldwide automotive area towards developing hybrid electric vehicles as an intermediate solution to fulfill the new, more stringent pollutant emission level requirements set by governments. Conversion of braking energy into electrical energy stored in the battery through regenerative braking is an important aspect of hybrid electric vehicles that increases their fuel efficiency. This paper presents an electric regenerative power assisted brake algorithm developed to enhance energy efficiency of a front and rear wheel drive parallel hybrid electric commercial vehicle. The commercial vehicle used in this study is a second generation research prototype Ford Transit Parallel Hybrid Electric Van. The existing hydraulic brake system of this van was not altered for reasons of safety and reliability in the case of a problem with regenerative barking.

This paper is on the application of electric power assisted steering and yaw stability control to a light commercial vehicle. An active steering system is developed and used for both purposes. Steering system and vehicle dynamics models are derived and built in Simulink and their response is compared to that of a validated Adams/Chassis model of the vehicle. A boost curve type electric power assisted steering controller and a yaw stability control system based on the model regulator steering controller are developed. Their performance is demonstrated through simulation results. A steering test rig built for safely developing steering controllers in a hardware-in-the-loop setting is introduced. Details of the experimental vehicle with active steering, built to test the concepts developed in the paper is also presented.

Advances in sensor solutions in the automotive sector make it possible to develop better ADAS and autonomous driving functions. One of the main tasks of highway chauffeur and highway pilot automated driving systems is to keep the vehicle between the lane lines while driving on a pre-defined route. This task can be achieved by using camera and/or GPS to localize the vehicle between the lane lines. However, both sensors have shortcomings in certain scenarios. While the camera does not work when there are no lane lines to be detected, an RTK GPS can localize the vehicle accurately. On the other hand, GPS requires at least 3 satellite connections to be able to localize the vehicle and more satellite connections and real-time over-the-air corrections for lane-level positioning accuracy. If GPS localization fails or is not accurate enough, lane line information from the camera can be used as a backup.

In this paper, the optimum linear/nonlinear spring and linear/nonlinear damper force versus displacement and force versus velocity characteristic functions, respectively, are determined using simple lumped parameter models of a quarter car front independent suspension and a half car rear solid axle suspension of a light commercial vehicle. The complexity of a nonlinear function optimization problem is reduced by determining the shape a priori based on typical shapes supplied by the car manufacturer and then scaling it up or down in the optimization process. The vehicle ride and handling responses are investigated considering models of increased complexity. The linear and nonlinear optimized spring characteristics are first obtained using lower complexity lumped parameter models. The commercial vehicle dynamics software Carmaker is then used in the optimization as the higher complexity, more realistic model.

Autonomous vehicle technology has been developing rapidly in recent years. Vehicle parametric uncertainty in the vehicle model, variable time delays in the CAN bus based sensor and actuator command interfaces, changes in vehicle sped, sensitivity to external disturbances like side wind and changes in road friction coefficient are factors that affect autonomous driving systems like they have affected ADAS and active safety systems in the past. This paper presents a robust control architecture for automated driving systems for handling the abovementioned problems. A path tracking control system is chosen as the proof-of-concept demonstration application in this paper. A disturbance observer (DOB) is embedded within the steering to path error automated driving loop to handle uncertain parameters such as vehicle mass, vehicle velocities and road friction coefficient and to reject yaw moment disturbances.

In recent years, there has been increasing research on automated driving technology. Autonomous vehicle path following performance is one of significant consideration. This paper presents discrete time design of robust PD controlled system with disturbance observer (DOB) and communication disturbance observer (CDOB) compensation to enhance autonomous vehicle path following performance. Although always implemented on digital devices, DOB and CDOB structure are usually designed in continuous time in the literature and also in our previous work. However, it requires high sampling rate for continuous-time design block diagram to automatically convert to corresponding discrete-time controller using rapid controller prototyping systems. In this paper, direct discrete time design is carried out. Digital PD feedback controller is designed based on the nominal plant using the proposed parameter space approach.

Having connectivity among ground vehicles brings about benefits in fuel economy improvement, traffic mobility enhancement and undesired emission reductions. On the other hand, Unmanned Aerial Vehicles (UAV) have proven to help in getting aerial data to end users in an affordable manner. When UAVs are equipped with cameras, they can get information about the terrain they are flying over. Moreover, using Vehicle-to-Everything (V2X) communication technologies, it is possible to form a communication link between UAVs and the connected ground vehicle networks comprising of Connected and Autonomous vehicles (CAVs). To investigate and exploit the potential benefits and use cases of a broad vehicle network, a microscopic traffic simulator modified previously by our group with the addition of nearby UAVs is used to integrate simulated Connected UAVs flying above a realistic simulation of heterogeneous traffic flow containing both CAVs and non-CAVs.

In the last decade, the accelerated advancements in manufacturing techniques and material science enabled the automotive industry to manufacture commercial vehicles at more affordable rates. This, however, brought about roadways having to accommodate an ever-increasing number of vehicles every day. However, some roadways, during specific hours of the day, had already been on the brink of reaching their capacity to withstand the number of vehicles travelling on them. Hence, overcrowded roadways create slow traffic, and sometimes, bottlenecks. In this paper, a Dynamic Speed Harmonization (DSH) algorithm that regulates the speed of a vehicle to prevent it from being affected by bottlenecks has been presented. First, co-simulations were run between MATLAB Simulink and CarSim to test different deceleration profiles.

Electronic stability control (ESC) has been an essential part of road vehicle safety for almost three decades. In April of 2007, the United States federal government issued a regulation to test the validity of ESC in development vehicles, and the regulation is called Federal Motor Vehicle Safety Standards (FMVSS) 126 in North America (NA), and an equivalent test in other countries outside of NA called ECE13-H (Economic Commission for Europe). While these standards have been used to certify ESC in development passenger cars for over a decade, this has not yet been scrutinized for the application of autonomous vehicles. Autonomous cars have sensors and control systems which can be used to improve ESC, where commercial standard vehicles do not.

Driver’s license examinations require the driver to perform either a parallel parking or a similar maneuver as part of the on-road evaluation of the driver’s skills. Self-driving vehicles that are allowed to operate on public roads without a driver should also be able to perform such tasks successfully. With this motivation, the S-shaped maneuverability test of the Ohio driver’s license examination is chosen here for automatic execution by a self-driving vehicle with drive-by-wire capability and longitudinal and lateral controls. The Ohio maneuverability test requires the driver to start within an area enclosed by four pylons and the driver is asked to go to the left of the fifth pylon directly in front of the vehicle in a smooth and continuous manner while ending in a parallel direction to the initial one. The driver is then asked to go backwards to the starting location of the vehicle without stopping the vehicle or hitting the pylons.