Refine Your Search

Date

Date

Topic

Topic

Wheels SAE IC Powertrain Steering Committee Assembling Materials

Search Results

Viewing 1 to 20 of 44
123Next >Last >>
Sort by published
Standard

Overcenter Clutch Spin Test Procedure
2012-10-23
CURRENT
J1079_201210
This SAE Recommended Practice applies to driving ring type overcenter clutches such as are used in industrial power takeoffs.
Standard

O.D. Coatings for Radial Lip-Type Shaft Seals
2002-10-25
CURRENT
J1947_200210
This SAE Information Report covers thin coatings of resinous based materials that can be placed on the metallic outer diameter of radial lip-type shaft seals to provide sealing when the mating bore finish is too rough to insure a proper seal (typically when finish exceeds 2.54 µm Ra, or in pressurized applications.) The coatings will have the following characteristics: a. Material shall dry to a tough, flexible, and non-tacky film. b. Thickness typically ranges from 0.005 to 0.076 mm. c. It shall not crack, flake, or powder when scraped. d. Coating shall adhere to seal case as noted in text. e. The sealer shall not show any evidence of peeling, blistering, softening, or dissolution when tested in media to be sealed.
Standard

THRUST WASHERS—DESIGN AND APPLICATION
1995-02-01
HISTORICAL
J924_199502
This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.
Standard

Thrust Washers – Design and Application
2011-06-13
CURRENT
J924_201106
This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.
Standard

THRUST WASHERS—DESIGN AND APPLICATION
1981-01-01
HISTORICAL
J924_198101
This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.
Standard

MAXIMUM ALLOWABLE ROTATIONAL SPEED FOR INTERNAL COMBUSTION ENGINE FLYWHEELS
1995-07-03
HISTORICAL
J1456_199507
This SAE Recommended Practice applies to flywheels and flywheel-starter ring gear assemblies used with internal combustion engines of the spark ignition and diesel type equipped with a governor or speed limiting device. Engine sizes are those capable of using SAE No. 6 through SAE No. 00 flywheel housings. This document applies to methods used to determine the rotational speed capability of flywheels for stresses imposed by centrifugal forces only.
Standard

Maximum Allowable Rotational Speed for Internal Combustion Engine Flywheels
2012-10-23
CURRENT
J1456_201210
This SAE Recommended Practice applies to flywheels and flywheel-starter ring gear assemblies used with internal combustion engines of the spark ignition and diesel type equipped with a governor or speed limiting device. Engine sizes are those capable of using SAE No. 6 through SAE No. 00 flywheel housings. This document applies to methods used to determine the rotational speed capability of flywheels for stresses imposed by centrifugal forces only.
Standard

MAXIMUM ALLOWABLE ROTATIONAL SPEED FOR INTERNAL COMBUSTION ENGINE FLYWHEELS
1984-12-01
HISTORICAL
J1456_198412
This practice applies to flywheels and flywheel-starter ring gear assemblies used with internal combustion engines of the spark ignition and diesel type equipped with a governor or speed limiting device. Engine sizes are those capable of using SAE No. 6 through SAE No. 00 flywheel housings. This practice applies to methods used to determine the rotational speed capability of flywheels for stresses imposed by centrifugal forces only.
Standard

MAXIMUM ALLOWABLE ROTATIONAL SPEED FOR INTERNAL COMBUSTION ENGINE FLYWHEELS
1990-06-01
HISTORICAL
J1456_199006
This SAE Recommended Practice applies to flywheels and flywheel-starter ring gear assemblies used with internal combustion engines of the spark ignition and diesel type equipped with a governor or speed limiting device. Engine sizes are those capable of using SAE No. 6 through SAE No. 00 flywheel housings. This document applies to methods used to determine the rotational speed capability of flywheels for stresses imposed by centrifugal forces only.
Standard

TURBOCHARGER NOMENCLATURE AND TERMINOLOGY
1979-11-01
HISTORICAL
J922_197911
This recommended practice applies to nomenclature of turbo-charger parts and terminology of performance. Modifying adjectives are omitted in some cases for the sake of simplicity. However, it is considered good practice to use such adjectives when they add to clarity and understanding.
Standard

Application Guide to Radial Lip Seals
2002-10-25
CURRENT
J946_200210
This SAE Recommended Practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of oil seals.
Standard

STANDARD CLASSIFICATION SYSTEM FOR NONMETALLIC AUTOMOTIVE GASKET MATERIALS
1990-06-01
HISTORICAL
J90_199006
The classification system provides a means for specifying or describing pertinent properties of commercial nonmetallic gasket materials. Materials composed of asbestos, cork cellulose, and other organic or inorganic materials in combination with various binders or impregnants are included. Materials normally classified as rubber compounds are not included, since they are covered in SAE J200 - ASTM D 2000. Gasket coatings are not covered, since details thereof are intended to be given on engineering drawings or in separate specifications.
Standard

NONMETALLIC GASKETS FOR GENERAL AUTOMOTIVE PURPOSES
1963-04-01
HISTORICAL
J90A_196304
These specifications for SAE J90 are intended to define the basic properties of commercial nonmetallic gasketing materials commonly used in automotive applications. These include materials composed of asbestos or other inorganic fibers, cork, or cellulose or other organic fibers, in combination with various binders or impregnants. Rubber compounds without fibrous or cork reinforcement are not included since they are covered in SAE Standard, Specifications for Elastomer Compounds for Automotive Applications—SAE J14, and in ASTM D 735-61T. Although the test methods and values are designed to describe the basic properties of the material in each category, they do not define all of, the properties which govern gasket performance. Caution should, therefore, be exercised in using these specifications as a basis for the selection of materials.
Standard

STANDARD CLASSIFICATION SYSTEM FOR NONMETALLIC AUTOMOTIVE GASKET MATERIALS
1995-03-25
HISTORICAL
J90_199503
The classification system provides a means for specifying or describing pertinent properties of commercial nonmetallic gasket materials. Materials composed of asbestos, cork, cellulose, and other organic or inorganic materials in combination with various binders or impregnants are included. Materials normally classified as rubber compounds are not included, since they are covered in SAE J200—ASTM D 2000. Gasket coatings are not covered, since details thereof are intended to be given on engineering drawings or in separate specifications.
Standard

Multiposition Small Engine Exhaust System Fire Ignition Suppression
2020-10-06
CURRENT
J335_202010
This SAE Recommended Practice establishes equipment and test procedures for determining the performance of spark arrester exhaust systems of multiposition small engines (<19 kW) used in portable applications, including hand-held, hand-guided, and backpack mounted devices. It is not applicable to spark arresters used in vehicles or stationary equipment.
Standard

SEALS—TERMINOLOGY OF RADIAL LIP
1997-05-01
HISTORICAL
J111_199705
The purpose of this SAE Recommended Practice is to provide a glossary of radial seal terms and nomenclature which are normally encountered in the design, manufacture, installation, testing, inspection, and failure mode analysis of radial seals. The information will aid in the understanding and communication among those people associated with radial seals.
Standard

Flywheels for Single-Plate Spring-Loaded Clutches
2012-05-31
CURRENT
J618_201205
This SAE Recommended Practice applies to flywheels for dry spring-loaded clutches used on internal combustion engines. Figure 1 and Tables 1, 2, and 3 report information currently used in the industry. Clutches requiring other dimensions are also manufactured. Dimensions given are primarily for single-plate clutches. Flywheels for two plate clutches have the same dimensions if an adaptor for the intermediate plate and second driven disc is supplied with the clutch. If instead the flywheel is to be extended to adapt the intermediate plate and second driven member, consult the clutch manufacturer for the required J dimension and drive arrangements for the intermediate plate. See SAE J1806 for flywheels for size 14 and 15.5 two plate pull-type clutches.
123Next >Last >>
X