Search Results

This paper presents the development of an engine simulation program for SI engines and its application to a two-stage expansion cycle. The two-stage expansion analysis is performed using the engine simulation, where a sudden expansion much faster than the normal expansion takes place during the expansion stroke. The changes in NO emissions and knock tolerance of the resulting new engine cycle are investigated for the same compression ratio. The changes in NO emissions and specific fuel consumption through increasing the compression ratio in order to return to the same amount of work done within the cycle are also studied.

This paper is concerned with the performance of the sensors and associated instrumentation used for the standard cetane tests for diesel fuels according to the ASTM D-613 procedure. The two primary sensors are replaced by modern units, and the analogue monitoring system is replaced by a digital one; the changes in the performance of the instrumentation system are then assessed. It is shown that the main source of inaccuracy in the measurement of ignition delay (on which the cetane test is based) is cyclic instability in the start of combustion, and that the current instrumentation and monitoring methods do not cope well with this instability. Although some of the cyclic variation can be ascribed to the instrumentation system, a large part is contributed by variability in the fuel ignition and injection processes. Improvements to the instrumentation and monitoring systems are presented and assessed.

A brief review is included of previous work aimed at quantifying the knock intensity from cylinder pressure measurements. This is used to identify some of the methods used in the current study. Digital signal processing techniques are also discussed, since their application to non-repetitive truncated signals can lead to results that are dependent on the techniques used. These problems are illustrated with some examples of windowing, and non-linear phase shift filters. A good correlation is demonstrated between knock severity indices calculated with energy methods in the time domain and the frequency domain. It is argued that it is easier to implement such knock indices in the lime domain. Use has also been made of mass fraction burn calculations in conjunction with data for the onset of knock, for data recorded simultaneously by two different pressure transducers.

The measurement of the instantaneous flame temperature and soot concentration in the combustion chamber of a running diesel engine can provide useful information relating to the formation of two important exhaust pollutants, NOx and particulates. The two-colour method is based on optical pyrometry and it can provide estimates of the instantaneous flame temperature and soot concentration. The theoretical basis of the method is outlined in a companion paper. This paper deals with the practical problems involved in the construction of a working system, including suitable calibration techniques. The accuracy of the measurements of flame temperature and soot concentration is also discussed using results from a various sources.

The two-colour method is based on optical pyrometry and can readily be implemented at a modest cost for the measurement of the instantaneous flame temperature and soot concentration in the cylinders of diesel engines. With appropriate modification, this method can be applied to other continuous and intermittent combustion systems, such as those for gas turbine and boiler burners. This paper outlines the theoretical basis of the method, with particular attention being paid to the assumptions relating to the evaluation of the flame temperature and soot concentration. A companion paper deals with the practical problems involved in constructing a working system, including suitable calibration techniques, and assessment of the method accuracy.

This is a first of a series of papers describing how the replacement of some of the inlet air with EGR modifies the diesel combustion process and thereby affects the exhaust emissions. This paper deals with only the reduction of oxygen in the inlet charge to the engine (dilution effect). The oxygen in the inlet charge to a direct injection diesel engine was progressively replaced by inert gases, whilst the engine speed, fuelling rate, injection timing, total mass and the specific heat capacity of the inlet charge were kept constant. The use of inert gases for oxygen replacement, rather than carbon dioxide (CO2) or water vapour normally found in EGR, ensured that the effects on combustion of dissociation of these species were excluded. In addition, the effects of oxygen replacement on ignition delay were isolated and quantified.

This is the second of a series of papers on how exhaust gas recirculation (EGR) affects diesel engine combustion and emissions. It concentrates on the effects of carbon dioxide (CO2) which is a principal constituent of EGR. Results are presented from a number of tests during which the nitrogen or oxygen in the engine inlet air was progressively replaced by CO2 and/or inert gases, whilst the engine speed, fuelling rate, injection timing, inlet charge total mass rate and inlet charge temperature were kept constant. In one set of tests, some of the nitrogen in the inlet air was progressively replaced by a carefully controlled mixture of CO2 and argon. This ensured that the added gas mixture had equal specific heat capacity to that of the nitrogen being replaced. Thus, the effects of dissociated CO2 on combustion and emissions could be isolated and quantified (chemical effect).

The extraction of small quantities of gas and particulates from diesel engine cylinders allows time-resolved gas and particulate analysis to be performed outside the engine during a short window of a few degrees crank angle at any stage of the engine cycle. The paper describes the design features and operation of a high-speed, intermittent sampling valve for extracting in-cylinder gases and particulates from diesel engines at any selected instant of the combustion process. Various sampling valve configurations are outlined. Detailed analysis of gas flow through the valve and the performance of the electromagnetic actuator and plunger are given in order to facilitate the design of the sampling valve. Finally, examples of the uses of the sampling valve in a direct-injection diesel engine are provided. These demonstrate how gaseous emissions such as NOx, uHC, CO2, and particulate emissions can be sampled at any part of the combustion process and analysed.

A numerical study was performed to elucidate the link between cyclic combustion variations in spark-ignition engines and instabilities in the non-linear processes occurring during the combustion. The instabilities in combustion were investigated by examining the response of a two-zone phenomenological combustion models to small deviations of mixture and flow conditions in the cylinder, such as the turbulence intensity at ignition, the overall equivalent ratio and the local equivalent ratio around the ignition site. The predicted combustion characteristics were validated and in good agreement with experimental data obtained from a single-cylinder research engine. The study suggested that the main deficiency of combustion in spark-ignition engines is the point-source ignition: it gives rise to slow development of initial flame; variations of the intermittent combustion process can occur when initial conditions at the ignition site are not repeatable from cycle to cycle.

Our earlier experimental study has shown that exhaust unburnt hydrocarbon emissions from spark-ignition engines can be reduced effectively by using in-cylinder catalysts on the surface of the piston top-land crevice. In order to improve the understanding of the process and mechanism by means of which unburnt hydrocarbon emissions are reduced, a phenomenological mathematical model was developed for catalytic oxidation processes in the piston-ring-pack crevice. This paper describes in details the modelling of the processes of the gas flow, mass diffusion and reaction kinetics in the crevices. The flow in the crevices is assumed to be isothermal and at the temperature of the piston crown surface. The overall rate of reaction is calculated using expressions for mass diffusion for laminar flows in channels and a first-order Arrhenius-type expression for catalytic reaction kinetics of hydrocarbon oxidation over platinum.