Search Results

In this study the authority of the available engine controls are characterized as the high load limit of homogeneous charge compression ignition (HCCI) combustion is approached. A boosted single-cylinder research engine is used and is equipped with direct injection (DI) fueling, a laboratory air handling system, and a hydraulic valve actuation (HVA) valve train to enable negative valve overlap (NVO) breathing. Results presented include engine loads from 350 to 650 kPa IMEPnet and manifold pressure from 98 to 190 kPaa. It is found that in order to increase engine load to 650 kPa IMEPnet, it is necessary to increase manifold pressure and external EGR while reducing the NVO duration. While both are effective at controlling combustion phasing, NVO duration is found to be a "coarse" control while fuel injection timing is a "fine" control.

Rapid progress in the interdisciplinary field of automotive engineering and the pressing need for an environmental friendly alternative to metal and synthetic fiber-reinforced composites for vehicle structure have triggered recent research in the field of natural fiber-based composites. Their potential advantages are attributed to their light weight, low cost and biodegradability. However, their usage in present day automotive systems is restricted due a lower magnitude range of mechanical properties and limited study in this area. In contrast to mechanical joints, the adhesively bonded joints aid in reducing stress concentration, joining of dissimilar materials, corrosion prevention, weight reduction and a smoother finish. Thus, in the present study, failure load, and mean shear stress of single lap shear and double lap shear joints as a function of joint overlap length, are evaluated using a two part epoxy adhesive made by Huntsman.

As engines advance toward greater efficiency and lower emissions, there is increasing need for accurate real-time residual models for engine control. Both the formulation of real-time-capable models and the development of methods for measuring or estimating residuals during engine calibration have been difficult and longstanding problems. This paper describes development of a low-cost, easy-to-use tool for on-line residual estimation in all cylinders of an IC engine. The basic method, hardware required, and software structure are described. The residual estimation tool was applied to estimate residuals over the operating map in all cylinders of a six-cylinder direct-injection SI engine equipped with dual-independent phasers. The data was used to calibrate a real-time residual model integrated into the engine management system. Validation data confirming accuracy of the model are presented.

Because of their robustness and cost performance, multi-hole gasoline injectors are being adopted as the direct injection (DI) fuel injector of choice as vehicle manufacturers look for ways to reduce fuel consumption without sacrificing power and emission performance. To realize the full benefits of direct injection, the resulting spray needs to be well targeted, atomized, and appropriately mixed with charge air for the desirable fuel vapor concentration distributions in the combustion chamber. Ethanol and ethanol-gasoline blends synergistically improve the turbo-charged DI gasoline performance, especially in down-sized, down-sped and variable-valve-train engine architecture. This paper presents the spray imaging results from two multi-hole DI gasoline injectors with different design, fueled with pure ethanol (E100) or gasoline (E0), under homogeneous and stratified-charge conditions that represent typical engine operating points.

This paper first presents a basic mean value engine plant model implemented in a hardware-in-the-loop (HIL) system. The plant model includes some basic engine parameters such as engine speed, manifold absolute pressure, etc., which are critical to both control algorithm integrity and default actions that result from improper signal performance (e.g., ECU shuts down due to corrupted signal(s)). The model is then improved to develop the HIL bench-based testing capabilities in the areas where a vehicle has traditionally been required. The on-board diagnostic monitor tests covered by SID $06 of SAE J1979 are selected as a case study. Specifically, for OBD exhaust gas sensor monitor testing purposes, the oxygen sensor model is developed to simulate normal or abnormal binary switching signals which might have asymmetric “lean to rich” and “rich to lean” transitions, or largely off maximum/minimum sensor voltages, etc.

Signals indicative of in-cylinder combustion have been under investigation for the control of diesel engines to meet stringent emission standards and other production targets in performance and fuel economy. This paper presents the results of an investigation on the use of the ion current signal for the close loop control of a heavy duty four cylinder turbocharged diesel engine equipped with a common rail injection system. A correlation is developed between the start of ion current signal (SIC) and the location of the peak of premixed combustion (LPPC) in the rate of heat release trace. Based on this correlation, a PID closed loop controller is developed to adjust the injection timing for proper combustion phasing under steady and transient engine operating conditions.

Gasoline direct injection provides reduced engine emissions, increased power, and increased fuel economy as compared to port fuel injection (PFI). Reduced emissions are largely due to starting the engine using high fuel pressure (up to 150 bar) and injecting into the compression stroke. During a cold start, fuel pressure must be increased from lift pump pressure (typically 4 to 6 bar) to desired injection pressure (typically 25 bar minimum). Start times are therefore impacted by the high pressure pump's ability to quickly build fuel pressure during crank. This study investigates the temperature and pressure affects during engine soak which allow vapor and air to form in the fuel system. Vapor and/or air in the system cause a slower fuel pressure build and increases start times. The scope of the problem and possible solutions were determined using theoretical and empirical testing.

Delphi has developed a Continuously Variable Valve Lift [CVVL] mechanism to improve spark ignition engine part throttle fuel economy through the minimization of pumping losses and reduction of cam drive torque. The latest CVVL design is focused on meeting valve lift duration targets derived from combustion analysis at key speed and load points, reducing packaging envelope, and reducing part count for low cost. Delphi's CVVL design process, simulation used to predict performance, and hardware confirmation testing will be presented and discussed in this paper.

This work is to propose a new Iterative Learning Observer (ILO)-based strategy for State Of Charge (SOC) estimation. The ILO is able to estimate the SOC in real time while identifying modeling errors and/or disturbances at the same time. An Electrical-Circuit Model (ECM) is adopted to characterize the Lithium-ion battery behavior. The ILO is designed based on this ECM and the stability is proved. Several experiments are conducted and the collected data is used to extract ECM parameters. The effectiveness of the estimated SOCs via ILO is verified by the experimental results. This implies that the ILO-based SOC determination scheme is effective to identify the SOC in real time.

SwRI has developed the DCO® ignition system, a unique continuous discharge system that allows for variable duration/energy events in SI engines. The system uses two coils connected by a diode and a multi-striking controller to generate a continuous current flow through the spark plug of variable duration. A previous publication demonstrated the ability of the DCO system to improve EGR tolerance using low energy coils. In this publication, the work is extended to high current (≻ 300 mA/high energy (≻ 200 mJ) coils and compared to several advanced ignition systems. The results from a 4-cylinder, MPI application demonstrate that the higher current/higher energy coils offer an improvement over the lower energy coils. The engine was tested at a variety of speed and load conditions operating at stoichiometric air-fuel ratios with gasoline and EGR dilution.

Estimation of soot in real time would help in the development of engine controls during engine production to meet the emissions goals and for on-board diagnostics. This paper presents a new approach to the estimate the soot emissions from the ion current measured inside the cylinder during engine operation. The investigation was carried out on a 4.5L heavy duty, turbocharged diesel engine. The glow plug was modified to act as an ion current probe, in addition to its main function. Algorithms were developed for the ion current signal to estimate the soot formed on a cycle-by-cycle basis. A comparison was made between the estimated soot emissions and measurements made by using an opacity meter under steady state as well as under transient engine operating conditions. In this research, a non-linear multiple regression model (NLMR) was used to estimate soot percentage from the ion current signal.

This paper investigates the relationship between NOx and ion current measured inside the combustion chamber of a heavy duty diesel engine under different operating conditions. Nevertheless, ion current is a local signal, thus it is important to measure NOx concentrations at the same exact location of the ion current probe. A novel technique is developed to simultaneously sample in-cylinder NOx and measure the ion current signal by adapting gas sampling probes for ion sensing. The cycle-resolved traces for the rate of heat release, NO mole fraction and ion current were analyzed to determine the contribution of the premixed combustion and the mixing-diffusion controlled combustion on NO formation and ionization in diesel engines.

RACam [1] is an Active Safety product designed and manufactured at Delphi and is part of their ADAS portfolio. It combines two sensors - Electronically Scanned RADAR and Camera in a single package. RADAR and Vision fusion data is used to realize safety critical systems such as Adaptive Cruise Control (ACC), Autonomous Emergency Braking (AEB), Lane Departure Warning (LDW), Lane Keep Assist (LKA), Traffic Sign Recognition (TSR) and Automatic Headlight Control (AHL). Figure 1 RACam Front View. With an increase in Active Safety features in the automotive market there is also a corresponding increase in the complexity of the hardware which supports these safety features. Delphi’s hardware design for Active Safety has evolved over the years. In Delphi’s RACam product there are a number of critical components required in order to realize RADAR and Vision in a single package. RACam is also equipped with a fan and heater to improve the operating temperature range.

Idealized mathematical models, also known as lumped parameter models (LPMs), are widely used in analyzing vehicles for ride comfort and driving attributes. However, the limitations of some of these LPMs are sometimes not apparent and a rigorous comparative study of common LPMs is necessary in ascertaining their suitability for various dynamic situations. In the present study, the mathematical descriptions of three common LPMs, viz. quarter, half and full car models, are systematically presented and solved for the appropriate response parameters such as body acceleration, body displacement, and, pitch and roll angles using representative passive suspension system properties. By carrying out a comparison of the three stated LPMs for hump-type road profiles, important quantitative insights, not previously reported in the literature, are generated into their behaviors so that their applications can be judicious and efficient.

In the current state of the art automotive fuel pumps there is only one channel on each side of the impeller. For high flow and pressure applications the size of such pumps becomes excessive. In order to reduce the size to a manageable level it may be necessary to have two or more channels on each side. But the problem with a multichannel pump is that the peak efficiency of each channel happens at a different operating point and the overall pump efficiency may not be that good. This problem can be overcome by synchronizing the channels. In a synchronous pump the channel diameter and cross sectional area of channels are such that the peak efficiency happens at the same operating point and the overall pump efficiency is improved. In this paper we derive the governing equations for flow, pressure and efficiency and layout a methodology for synchronizing the channels.

Despite being developed more than 100 years ago, the diesel engine has yet to achieve mass acceptance in the North American passenger car sector. In most other parts of the world, however, diesel engines have made considerable strides due in part to the common rail fuel injection system. Significant fuel economy, reduced exhaust emissions, invincible low-speed torque, and all-around good drivability are a few of the benefits associated with common rail technology, which are covered in-depth in Diesel Common Rail and Advanced Fuel Injection Systems.