Search Results

The passenger car automakers are always competing to excel in vehicle characteristics related to passenger comfort and driveability aspects. The engine calibration is a theoretical and experimental procedure with the intention to extract maximum efficiency from the engine and guarantee satisfactory levels of driving for both conventional and racing cars. This paper describes the calibration procedure of a Formula SAE race car engine. The engine was a four cylinder 600 cm3 four-strokes with modified intake and exhaust systems, controlled by an engine control unit (Motec M800 ECU). These engines present optimized characteristics for high speed, in exchange for some combustion degradation in some specific operating conditions at low speed that may impair vehicle driveability. Therefore, good tip-in reaction and the progression of the torque delivery are fundamental criteria to increase the vehicle performance, specially, to those submitted to short acceleration distances.

In the way of achieving maximum performance of a racecar several aspects of it have to be optimized. The whole picture of vehicle performance involves crossing data to find relationship among systems and identifying trends, pitfalls and optimum points. In this paper, a straightforward software tool for tire data analysis is developed and described. The software aims to integrate tire data analysis in early stages of the development process of a Formula SAE racecar. In addition, it is thought to be a learning environment to fresh team members. To establish and achieve the necessary goals, an affordancebased model was used to elicit user needs. Regarding the tires, it was possible to precisely point out what data is required to quickly fit a Pacejka tire mode and to cross raw tire data of different tires and preview the steady state balance of a vehicle.

Renewable fuels have received more attention in the last few decades since the fuel demand is constantly increasing. In this scenario, fuels from vegetable oils are emerging as an interesting alternative. In this study, biodiesel produced from used cooking oil was studied. Several concentrations of biofuel were tested to evaluate their performance and combustion characteristics i.e. 7% (B07), 17% (B17), 27% (B27), 52% (B52), 77% (B77) and 100% by volume of Biodiesel (B100) on conventional diesel. Tests were conducted in a single cylinder four-stroke compression ignition engine. A 1-D computational model was built and compared to experimental results. The biodiesel concentration in the blends had influence on engine performance by increasing fuel consumption due to its reduced lower heating value. In addition, larger fractions of biodiesel on conventional diesel presented higher peak of heat release.

Ethanol with high levels of hydration is a low cost fuel that offers the potential to replace fossil fuels and contribute to lower carbon dioxide (CO2) emissions. However, it presents several ignition challenges depending on the hydration level and ambient temperature. Advanced combustion concepts such as homogeneous charge compression ignition (HCCI) have shown to be very tolerant to the water content in the fuel due to their non-flame propagating nature. Moreover, HCCI tends to increase engine efficiency while reducing oxides of nitrogen (NOx) emissions. In this sense, the present research demonstrates the operation of a 3-cylinder power generator engine in which two cylinders operate on conventional diesel combustion (CDC) and provide recycled exhaust gas (EGR) for the last cylinder running on wet ethanol HCCI combustion. At low engine loads the cylinders operating on CDC provide high oxygen content EGR for the dedicated HCCI cylinder.

The prediction of ignition delay times is very useful during the development phase of internal combustion engines. When it comes to biofuels such as ethanol and its blends with gasoline, its importance is enhanced, especially when it comes to flex-fuel engines and the need to address current and future emissions legislations and efficiency goals. The ignition delay time measured as the angular difference between the spark discharge time, as commanded by the ECU and a relevant fraction of fuel mass burned (usually, 2, 5 or 10%). Experimental tests were performed on a downsized state-of-the-art internal combustion engine. Engine speed of 2500 rpm, with load of 6 and 13 bar IMEP were set for investigation. Stoichiometric operation and MBT or knock-limited spark timings were used, while valve overlap was varied, in order to address the effects of scavenging and residuals on ignition delay times.

Stringent emission legislations have pushed engine operation to borderline knock. Knocking combustion limits engine efficiency, putting a threshold in carbon emission reduction that impairs further decarbonization of the transport sector. In this way, online knock monitoring is very important during engine development and calibration to allow operation with higher efficiency levels. Commonly, knock detection methods require complex calculations with high computational cost. Furthermore, these methods normally need previous calibration of a threshold value for each specific engine to indicate the knock limit, requiring important engineering resources and time. Hence, this paper proposes a novel methodology for knock detection that is simple, does not require prior calibration and can be used for sensorless knock detection. The method is applied by relating the crank angle of maximum pressure rise rate (AMPRR) with the angle of 50% of fuel mass burned (CA50), the so-called G Index (GI).

Low cost ethanol with high levels of hydrations is a fuel that can be easily produced and that offers the potential to replace fossil fuels and contribute to reduce greenhouse gas emissions. However, it shows several ignition challenges depending on the hydration level, ambient temperature compression ratio and other engine-specific aspects. Advanced combustion concepts such as homogeneous charge compression ignition (HCCI) have shown to be very tolerant to the water content in the fuel due to their non-flame propagating nature. Moreover, HCCI tends to increase engine efficiency while reducing oxides of nitrogen (NOx) emissions. In this sense, the present research demonstrates the operation of a 3-cylinder power generator engine in which two cylinders operate on conventional diesel combustion (CDC) and provide recycled exhaust gas (EGR) for the last cylinder running on wet ethanol HCCI combustion.

In the present paper, a typical Formula SAE double-wishbone suspension is discussed. This study aims to point out a preliminary chassis setup to reduce testing time on track and improve the overall performance of a prototype in a Formula SAE Skid Pad event. The influence of kinematic parameters of the suspension are analyzed to quantify how they change the capability of the tire to generate lateral force due to camber effects. To enhance results, special attention is given to a Magic Formula tire model based on a constrained forces and moments tire test data. Camber and Ackermann steering geometry showed up as major tuning tools to attempt during test period.

Several motorsport competitions impose restrictions on intake systems to limit maximum engine power. Since the restriction interferes with the efficiency of the intake system as a whole, it is necessary to study ways to minimize the negative effect of changes in engine performance. In practice, the regulation imposes restrictions to the inlet air which motivates the search for the minimum pressure loss in the restrictor while maintaining an equal volumetric efficiency between the cylinders. This way, it is necessary to tune the duct lengths and diameters, and plenum volume to obtain the maximum volumetric efficiency in the most required speeds. Formula SAE competition imposes an intake system restriction of 20 mm or 19 mm diameter (for gasoline or ethanol fueled engines, respectively). Thus, to reduce pressure loss in the imposed restriction orifice, a system with a convergent divergent duct forming a venturi tube was used.

Experimental aviation engines face numerous challenges, including the need for energy efficiency, alternative fuel sources, reduced weight and size, greater durability with reliability, emissions reduction, and integration with advanced control and monitoring systems. This study presents the performance of a two-stroke engine with a Uniflow scavenging system with a flathead valve concept, with lower specific fuel consumption than conventional two-stroke aircraft engines. The engine’s maximum speed is limited to 3000 rpm for better cylinder scavenging efficiency, which also eliminates the need for a reduction gearbox, simplifies the design, and reduces the engine’s total mass. 1D simulations were conducted to evaluate combustion and performance parameters using aviation.