Search Results

Three-dimensional transient simulations using KIVA-3V were conducted on a 4-stroke high-compression ratio, methanol-fueled, direct-injection (DI) engine. The engine had two intake ports that were designed to impart a swirling motion to the intake air. In some cases, the intake system was modified, by decreasing the ports diameter in order to increase the swirl ratio. To investigate the effect of adding shrouds to the intake valves on swirl, two sets of intake valves were considered; the first set consisted of conventional valves, and the second set of valves had back shrouds to restrict airflow from the backside of the valves. In addition, the effect of using one or two intake ports on swirl generation was determined by blocking one of the ports.

Numerical simulations of lean Methanol combustion in a four-stroke internal combustion engine were conducted on a high-compression ratio engine. The engine had a removable integral injector ignition source insert that allowed changing the head dome volume, and the location of the spark plug relative to the fuel injector. It had two intake valves and two exhaust ports. The intake ports were designed so the airflow into the engine exhibited no tumble or swirl motions in the cylinder. Three different engine configurations were considered: One configuration had a flat head and piston, and the other two had a hemispherical combustion chamber in the cylinder head and a hemispherical bowl in the piston, with different volumes. The relative equivalence ratio (Lambda), injection timing and ignition timing were varied to determine the operating range for each configuration. Lambda (λ) values from 1.5 to 2.75 were considered.

A numerical study on the combustion of Methanol in a directly injected (DI) engine was conducted. The study considers the effect of the bowl-in-piston (BIP) geometry, swirl ratio (SR), and relative equivalence ratio (λ), on flame propagation and burn rate of Methanol in a 4-stroke engine. Ignition-assist in this engine was accomplished by a spark plug system. Numerical simulations of two different BIP geometries were considered. Combustion characteristics of Methanol under swirl and no-swirl conditions were investigated. In addition, the amount of injected fuel was varied in order to determine the effect of stoichiometry on combustion. Only the compression and expansion strokes were simulated. The results show that fuel-air mixing, combustion, and flame propagation was significantly enhanced when swirl was turned on. This resulted in a higher peak pressure in the cylinder, and more heat loss through the cylinder walls.

Collection of diesel exhaust using the Tapered Element Oscillating Microbalance (TEOM) instrument was investigated as an alternative to the traditional method of filter weighing for particulate matter mass determination. Such an approach, if successful, would eliminate considerable manual labor involved in weighing, as well as the delay of hours or days before final results were known. To avoid known artifacts in the second-by-second mode of operation, the TEOM was used in a phase-by-phase mode and was equilibrated with air of constant temperature and humidity before each measurement. Electrically operated valves were used to automate the equilibration and measurement process. The study also included a comparison between two types of TEOM filter - an older type and a new one designed by the TEOM manufacturer for more uniform flow and less flexing. Best results were obtained with the TEOM using the new filter under no-flow conditions.

A high-speed/high-resolution imaging technique and analysis were applied to study fuel injector spray timed evolution in ambient air and in a motored single-cylinder engine. Alcohol fuel was injected from a mid-pressure injection system into the engine cylinder at shaft speed of 1,000 rpm. The fuel injection system with various nozzles was designed for use in the EPA/NVFEL program to develop clean and efficient engines that use alternative fuels. A 15W copper vapor laser with a fiber optic delivery system synchronized with a high-speed drum streak camera was utilized to expose films at 5,000 frames per second (fps). The spray characteristics were investigated at 15.0 MPa injection pressure and injection duration range of 3-5 ms. A sequence of successive frames was selected from the films to examine the influence of the injector parameters and the valve lift on the atomization process. The spray penetration was quantified by analyzing the high-speed films.

Dynamic traction testing of a sample of drive tires for class 8 tractor-trailers provides information about the relation among rolling resistance, tire design, and traction performance in snow conditions. The tests were conducted to address concerns that low rolling resistance tires used to save fuel and reduce emissions may have inferior traction on snow. In addition to the dynamic traction testing, based on ASTM F-1805, rolling resistance was tested using ISO 28580, and characteristics of the tread design were measured, including tread depth and void ratio, using ASTM F421 and ASTM F-870. In general, tires designed for increased traction, usually made with open shoulders, had a higher snow traction rating than tires designed for highway applications with closed shoulders. There was no significant correlation between the snow traction rating and the coefficient of rolling resistance.

Three-dimensional numerical simulations of a diesel-fueled engine with a pre-chamber located in the cylinder head and a bowl in the piston were performed. The study considers the effect of diesel combustion in the pre-chamber on turbulence generation and hence fuel-air mixing and combustion in the piston-bowl. Diesel fuel was injected directly into the pre-chamber and the piston bowl at different times. In order to better determine the effect of pre-chamber combustion on the main chamber combustion, various pre-chamber injection timings were considered. The results show that pre-chamber combustion caused the average cylinder pressure to increase by up to 20% in some cases.

This paper presents a review of the regulatory, environmental, and health issues surrounding the use of halons as a fire suppressant and a summary of the recently completed Racecar Fire Suppressant Exposure Study by ICF Consulting, Inc., under contract with the U.S. Environmental Protection Agency (EPA) (U.S. EPA, 2004a). In 2003 the EPA learned that the SFI Foundation Inc., the organization responsible for developing safety regulations and testing requirements for numerous Performance Racing Industry (PRI) sanctioning bodies, was revising its Quality Assurance Specification for On Board Fire Suppression Systems (SFI Specification 17.1). The previous Specification 17.1 required either halon 1211 or halon 1301 to be used in these systems. Halons are ozone-depleting substances (ODS) widely used in fire protection applications and whose production and use are controlled under the Montreal Protocol and the Clean Air Act (CAA).

The purpose of the 4-SPACE (4-Stroke Powered gasoline Auto-ignition Controlled combustion Engine) industrial research project is to research and develop an innovative controlled auto-ignition combustion process for lean burn automotive gasoline 4-stroke engines application. The engine concepts to be developed could have the potential to replace the existing stoichiometric / 3-way catalyst automotive spark ignition 4-stroke engines by offering the potential to meet the most stringent EURO 4 emissions limits in the year 2005 without requiring DeNOx catalyst technology. A reduction of fuel consumption and therefore of corresponding CO2 emissions of 15 to 20% in average urban conditions of use, is expected for the « 4-SPACE » lean burn 4-stroke engine with additional reduction of CO emissions.

This paper presents results from a study of the particle size distributions emitted by a heavy-duty diesel engine equipped with a common-rail fuel injection system. The study focused on two key sampling and engine operating variables: dilution ratio and fuel injection pressure. Results show that the number mean diameter of the particle size distributions decreased with increasing dilution ratios. Also, the total number concentration of particles did not change with different dilution ratios. In addition, it was found that fuel injection pressures affected the size distribution of the particles sampled. Under some engine operating conditions increasing the fuel injection pressure resulted in an increased number of nuclei mode particles.

The paper analyzes energy use and emissions per GJ of various fuels delivered to the vehicle fuel tank, covering extraction, fuel production, transportation, storage, and distribution phases of the life cycle of alternative fuels. Drawing on a number of existing studies, the modeling issues and approaches, main results and insights are summarized. The range of estimates in various studies is large; however, common patterns can be observed. The analysis indicates, that conventional gasoline fuel cycle has robust advantages with respect to energy efficiency, conventional pollutant emissions, and most importantly, existing infrastructure compared to alternative fuels. Fossil fuel based alternatives like CNG, NG–Methanol, NG–FTL do not result in significant improvement in fuel cycle environmental performance. Biofuels offer the benefits of lower and even negative GHG emissions, sustainability, and domestic fuel production.