Search Results

To achieve power output and cooling performance in motorcycle air-cooled engines equivalent to those in water-cooled engines, an engine utilizing air-flow generated by the moving motorcycle and a new oil-cooling system for an air-cooled engine was studied. The engine temperature distribution was obtained based on a CFD (Computational Fluid Dynamics) analysis of cooling-air/oil behavior using an inline four-cylinder 900cm3 engine. As a result of this study, engine temperature was sufficiently decreased and the difference in temperature among cylinders was reduced; the engine was tested in a prototype motorcycle.

The aim of the experiment is to observe the exhaust gas flow starting from the exhaust manifold to the catalytic converter at the 4 stroke engine of the passenger car to enhance the system's improvement. The manifold connects each exhaust pipe from the engine cylinders to the catalytic converter. The velocity pattern inside the exhaust manifold is measured using particle image velocimetry (PIV) meanwhile the time series velocity data is measured by Laser Doppler Anemometer (LDA). In the experiment, flow conditions with four pipes working simultaneously or single pipe working independently are tested. The initial velocity condition shown in the next is set at the upstream where the flow is inside the circular pipe. The initial velocity is 28m/s for the all pipes acting and 14m/s for each pipes acting. There are also 3 conditions of measurement: with catalytic converter, without catalytic converter and with hollow catalytic converter.

The lubrication mechanism is discussed by measuring the oil film behavior. The oil film behavior is evaluated by the oil film thickness and oil film velocity map. The combination method of laser induced fluorescence method (LIF) and particle image velocimetry (PIV) is applied to measure the oil film behavior. The oil film thickness is measured by LIF and its velocity distributions are measured by PIV. The combination method can provide both of the film thickness and velocities simultaneously. The first trial is performed in the model engine for checking the dynamics measurement of the oil film thickness by the LIF. The results show a difference of the oil film thickness distribution with crank angle. The combination method is tested in the engine with 4-cycle and 2-cylinder optical access engine with motoring condition. One cylinder of the engine is sapphire cylinder for observing oil film behavior on the piston skirt. Two clearances of the piston skirt of 30 µm and 100 µm is tested.

Air velocities in the cylinder of motored engine were measured by laser Doppler anemometer (LDA) and particle image velocimetry (PIV) to make the standard database that will be used for verification of the numerical simulation. A 4-stroke, 4-valve test engine with transparent cylinder was operated with engine speed of 600rpm. The velocities on that condition were measured individually in vertical- and swirl-direction. The distributions of mean- and RMS- velocities are obtained from the measured data. Flow velocity through the intake valve was also measured at the top of the cylinder. As the results, the flow structure by each crank angle can be clarified. The present data can be commonly used for some numerical research group of RC238 in JSME for verification of numerical simulation results. The effect of the tumble generation valve (TGV) is evaluated by velocity distributions.

This paper presents two factors for improving the performance and emissions characteristics in HCCI diesel combustion, one is reducing compression ratio and another is changing the injector position. In a previous study, it was shown that HCCI diesel combustion could be realized by utilizing a hollow-cone spray with normal injection pressure. However there remained two major problems of engine instability and increase in BSFC (decrease in brake thermal efficiency). By reducing the compression ratio from 18.8 to 16.8, the engine stability was much improved to the level of conventional diesel combustion and the increase in BSFC became almost half, which was mainly due to the change of combustion phasing. In addition to this, application of 5 mm inside position of the injector realized almost no penalty of BSFC at higher load condition.

Velocity measurement of an intermittent high-speed flow inside a micro wave rotor cell was carried out using a laser Doppler anemometry (LDA). The cell is 3 × 3 mm rectangular tube, whose length is 42 mm. The pressure ratio and rotor speed of the wave rotor were set at 2.5 and 5,000 rpm, respectively. Ethanol droplets were seeded into the flow as scattering particles. By use of laser beam expanders, the probe volume of the LDA optics was minimized, and sub-millimeter special resolution is realized while a wide velocity range (-100 to 300 m/s) is kept. It is shown that the velocity histories at local positions inside the wave rotor cell can be obtained with the LDA optics. The rapid velocity increase and decrease, due to the primary and secondary shock waves, are observed, and the propagation speed of the shock waves was estimated. It is shown that the velocity profile inside the cell is flat and that the boundary layer thickness inside the cell is smaller than 0.5 mm.

The combination method for measuring the oil film thickness and velocity is proposed. The oil film thickness is measured by laser induced fluorescence (LIF) method and its velocity is measured by particle image velocimetry (PIV). A model engine is employed in order to check the LIF measurement for oil film thickness, and an optical access engine based on production engine is utilized for both measurements of oil film thickness and velocity. In the combination method, LIF images are used in the PIV measurement instead of particle images. From the results, the oil film thickness and velocity can be measured simultaneously by the combination method utilizing only LIF dye. The oil film thickness and velocity are presented along with crank angle of the engine under the motoring operation. The oil film velocity is also measured under the firing operation.

This paper describes the evaluation of flow characteristics inside a model engine cylinder using particle image velocimetry (PIV), laser Doppler anemometry (LDA), and numerical simulation by Partial Cells in Cartesian coordinate (PCC) method. The main goal of the study is to clarify the differences in the velocity characteristics obtained by these methods. The model engine head has a four-valve system. Single- and dual- valve opening conditions of the model engine head were tested by a steady flow test rig. The flow structures were completely different for these valve opening conditions. The mean velocities and their distributions obtained by the three methods show satisfactory agreement. However, there were differences in the turbulence intensities under several conditions and measuring positions. Taylor's hypothesis in the integral length scale of turbulence was also compared with single LDA and PIV measurements.