Search Results

This paper presents the experimental investigation of combustion stability and nano-particle emissions from the CNG-diesel RCCI engine. A modified automotive diesel engine is used to operate in RCCI combustion mode. An open ECU is used to control the low and high reactivity fuel injection events. The engine is tested for fixed engine speed and two different engine load conditions. The tests performed for various port-injected CNG masses and diesel injection timings, including single and double diesel injection strategy. Several consecutive engine cycles are recorded using in-cylinder combustion pressure measurement system. Statistical and return map techniques are used to investigate the combustion stability in the CNG-diesel RCCI engine. Differential mobility spectrometer is used for the measurement of particle number concentration and particle-size and number distribution. It is found that advanced diesel injection timing leading to higher cyclic combustion variations.

Fatigue design has to account for the scatter of component geometry, material behavior and loading. Scatter of the first two variables is mainly due to manufacturing and material sourcing. Loading on the other hand depends decisively on operating conditions and customer usage. Loading is certainly most difficult to determine. Tests on proving ground or even long-term real time measurements are used to obtain actual load time histories. Because of the costs of measurements and safety measure, real-time measurements are used exceptionally to gain changes in the usage profile. In this paper, an attempt has been made to find the difference in the extrapolated data to the actual data. A comparison has been made between the actual road distance of 2000 km to the extrapolated data of 100 km, 500 km and 1000 km to 2000 km. The front Axle channel is taken for the study.

An analysis of the rollover propensity of a make of a TSR used extensively in S.E. Asia roads is presented using a 6-degree of freedom simulation. Verification of the model was against measured accelerations measured over speed breakers. Rollover stability was analyzed through simulating Increasing Steer, NHTSA J Turn, and Road Edge Recovery maneuvers.

Advanced research in ABS (Anti-lock Braking System), traction control, electronic LSD's (Limited Slip Differential) and electrical powertrains have led to an architecture development which can be used to provide a controlled yaw moment to stabilize a vehicle. A steer assistance mechanism that uses the same architecture and aims at improving the vehicle response to the driver steering inputs is proposed. In this paper a feed-forward approach where the steering wheel angle is used as the main input is developed. An optimal control system is designed to improve vehicle response to steering input while minimizing the H2 performance of the body slip angle. The control strategy developed was simulated on a 14 DOF full vehicle model to analyze the response and handling performance.

A novel Air-Alcohol INDUCTOR with an inherent flexibility to tailor the alcohol flow rate, has been developed for a multi-cylinder, variable-speed, vehicular Diesel engine to enable operation in the Alcohol-Diesel bi-fuel mode. Tests have been carried out on the dynamometer over the whole speed range of the engine. Also road tests have been carried out under constant vehicular speed conditions. Upto 48% Diesel substitution was achieved on road without reduction in thermal efficiency. Laboratory tests indicate lower exhaust temperatures and lower smoke intensities than in the diesel mode.

This paper deals with simulation studies on surface densification of PM gears by rolling process using finite element method. The PM gear is considered as a porous continuum and analysis is performed using constitutive relations based on Gurson model for porous materials. The influence of various parameters such as initial position of mating gears, braking torque applied, friction between mating surfaces and roll stock allowance on the process have been studied. The density obtained by the process is highly influenced by the braking torque applied. The results presented provide a better understanding of the PM gear rolling process.

Road accidents and persons killed in India have been reported to the tune of 4,90,383 and 1,38,258 respectively during 2012. On National Highways (NHs), major share of accidents (about 29%) and number of persons killed (35.3%) are observed out of total accidents. National Highways in India constitute about 2% of total road network (92,851 km) in India, but carries about 40% of traffic. 46% (42,829 km) of NHs in India comprises of two-lane and about 19% (17239 km) of NHs are single or intermediate-lane. Road accidents being multi-disciplinary in nature involves attention of multiple departments such as Highways Authority, Police, Motor Vehicles, Automobile Manufacturers, NGOs, etc. Owing to spurt in growth of motor vehicle population in India, road accidents are not reduced significantly despite improvement in NHs (widening of carriageway and riding quality).

Improving vehicle performance in terms of both torque and power is a strong customer need in both conventional and electric vehicles. In this work, different two speed automatic transmission (AT) concepts are developed to improve the energy efficiency and performance of battery electric two wheelers. Developed transmission systems are simple, compact and cost effective and results in relatively high energy efficiency of an electric motor. The unique shift control strategy ensures motor to operate at higher efficiency zones to minimize the overall energy consumption. Virtual simulations of electric vehicle were carried out for different driving conditions and optimal transmission ratios were determined. Mechanical behaviors such as gear shift characteristics, linear and angular velocities, inertial forces of each components are analyzed by using Multi body dynamics simulation. Forces predicted here are further used for durability studies of these components.

This research paper focuses on the modelling and analysis of a flywheel energy storage system (FESS) specifically designed for electric vehicles (EVs) with a particular emphasis on the flywheel rotor system associated with active magnetic bearings. The methodology used simulation approaches to investigate the dynamics of the flywheel system. The objective of this study is to explore the effects of implementing the flywheel energy storage system on the performance of the EV. The paper presents a comprehensive model of the flywheel energy storage system, considering the mechanical and electrical aspects. The mechanical model accounts for the dynamic behaviors of the flywheel, including parameters such as rotational speed, inertia, and friction. The electrical model describes the interaction between the flywheel and the power electronics, such as the converter and motor/generator. To evaluate the benefits of the flywheel energy storage system, simulations are conducted.