Search Results

This paper gives a history of simulation of commercial vehicles, starting with the early models and progressing to today's multibody models. This is followed by a discussion of the key questions faced by simulators. Finally, the paper presents a new method to postprocess results through videoanimation.

This paper applies basic statistics to the simulation of vehicle dynamics in the time domain and the frequency domain. The methods presented here yield an expectation for the variation of the computed results as a function of variation in input parameters. Applications include important steady state measures of vehicle performance such as understeer gradient and yaw rate gain. Follow up analysis includes measures of transient response in the time domain and of amplitude and phase relationships in the frequency domain. There are several potential applications for this methodology, perhaps most important, an understanding of the consequences of parameter uncertainty on the credibility of simulated results.

This paper presents an analytical study of the performance improvements that can be obtained at both high and low speed using multiple steered axles on heavy articulated trucks. At high speed, rollover usually represents a worst case scenario. Therefore we have chosen to evaluate possible steering designs based on their ability to reduce lateral acceleration of the semitrailer center of gravity. This is in contrast to passenger cars where four-wheel steering has typically been evaluated based on measures that were thought to be related to driver acceptance. This paper also investigates the effects of steering rear tractor axles on the low-speed maneuverability of the vehicle. Steering algorithms for the rear tractor tires were evaluated using frequency response and simulation of an obstacle avoidance maneuver. Results indicate that at high speeds considerable reductions in trailer lateral acceleration can be obtained during transient maneuvers.

The objective of this work was to identify methods of reliably predicting optimum operating conditions in an experimental compression ignition engine using multiple injections. Abstract modeling offered an efficient way to predict large volumes data, when compared with simulation, although the initial cost of constructing such models can be large. This work aims to reduce that initial cost by adding knowledge about the favorable network structures and training rules which are discovered. The data were gathered from a high pressure common rail direct injection turbocharged compression ignition engine utilizing a high EGR configuration. The range of design parameters were relatively large; 100 MPa - 240 MPa for fuel pressure, up to 62% EGR using a modified, long-route, low pressure EGR system, while the pilot timing, main timing, and pilot ratio were free within the safe operating window for the engine.

Accurate quantification of 3D shapes of the complex ice structures accreted on wind turbine blades is highly desirable to develop ice prediction models for more accurate prediction of the aerodynamic performance degradation and power reduction due to the ice accretion on wind turbine blades. In the present study, an experimental investigation was conducted to quantitatively characterize the 3D shapes of the ice structures accreted over a DU91-W2-250 wind turbine airfoil model in the Icing Research Tunnel available at Iowa State University (ISU-IRT). A glaze icing condition and a rime icing condition that wind turbines usually experience in winter were duplicated by using ISU-IRT. A high-resolution non-intrusive 3D scanning system was used to make detailed 3D-shape measurements to quantify the complicated ice structures accreted on the wind turbine airfoil model as a function of the ice accretion time.

An explorative study was performed to demonstrate the feasibility of using a novel hybrid anti-/de-icing strategy for aircraft icing mitigation. The hybrid method was developed by combining the electro-thermal heating mechanism and specialized surfaces/coatings with different wettabilities. While an electrical film heater was utilized to provide thermal energy around the leading edge of a NACA0012 airfoil model, two different coating strategies, (i.e., (a). Superhydrophobic coating covering the entire airfoil surface to increase droplets bounce-off and accelerate surface water runback vs. (b). super-hydrophilic coating at the leading edge to increase evaporation area + superhydrophobic coating in downstream to prevent runback refreezing) were proposed and evaluated aiming at maximizing the anti-/de-icing efficiency of the hybrid method.

In the present study, an experimental investigation was conducted to characterize a hot-air-based anti-/de-icing system for the icing protection of aero-engine inlet guide vanes(IGVs). The experimental study was conducted in a unique icing research tunnel available at Iowa State University (i.e., ISU-IRT). A hollowed IGV model embedded with U-shaped hot-air flowing conduit was designed and manufactured for the experimental investigations. During the experiments, while a high-speed imaging system was used to record the dynamic ice accretion or anti-/de-icing process over the surface of the IGV model for the test cases without and with the hot-air supply system being turned on, the corresponding surface temperature distributions on the IGV model were measured quantitatively by using a row of embedded thermocouples.

The electro-thermal method is most commonly used for wind turbine anti-/de-icing. The upmost drawback of such systems is the high power consumption. In the present study, we proposed to use a durable slippery liquid-infused porous surface (SLIPS) to effectively reduce the power requirement of the heating element during the anti-/de-icing process. The explorative study was conducted in the Icing Research Tunnel at Iowa State University (ISU-IRT) with a DU91-W2-250 wind turbine blade model exposed under severe icing conditions. During the experiments, while a high-speed imaging system was used to record the dynamic ice accretion process, an infrared (IR) thermal imaging system was also utilized to achieve the simultaneous surface temperature measurements over the test model.

An experimental study was conducted to investigate the dynamic ice accretion processes on bridge cables with different surface modifications (i.e., 1. Standard plain, 2. Pattern-indented surface, and 3. helical fillets). The icing experiments were performed in the unique Icing Research Tunnel available at Iowa State University (i.e., ISU-IRT). In order to reveal the transient ice accretion processes and the associated aerodynamic loadings on the different cable models under the different icing conditions (i.e., rime vs. glaze), while a high-speed imaging system was used to capture the transient details of the surface water transport and ice accretion over the cable surfaces, a high-accuracy dual-transducer force measurement system was also utilized to measure the aerodynamic loadings acting on the ice accreting cable models.

Understanding the fundamental details of drop/wall interactions is important to improving engine performance. Most of the drop-wall interactions studies are based on the impact of a single drop on the wall. To accurately mimic and model the real engine conditions, it is necessary to characterize spray/wall interactions with different impingement frequencies at a wide range of wall temperatures. In this study, a numerical method, based on Smoothed Particle Hydrodynamics (SPH), is used to simulate consecutive droplet impacts on a heated wall both below and above the Leidenfrost temperature. Impact regimes are identified for various impact conditions by analyzing the time evolution of the post-impingement process of n-heptane drops at different impingement frequencies and wall surface temperatures. For wall temperature below the Leidenfrost temperature, the recoiled film does not leave the surface.