Search Results

In the air conditioning system, flow-induced noise is very disturbing, including the noise generated in the expansion device and the heat exchangers. In the past few decades, most researches related to flow-induced noise focused on the relationship between the flow regimes near the expansion device and the amplitude of flow-induced noise when the measurements are not synched. In this paper, an experimental approach is used to explore the simultaneous relationships between flow-induced noise characteristics and flow regimes at the inlet of TXV of evaporators used in automobiles. A pumped R134a loop with microphones and transparent visualization sections is used to simulate the vapor compression system. Also, the paper evaluates the severity of flow-induced noise from not only the amplitude of noise but also the frequency of noise with a parameter called psychoacoustic annoyance (PA).

As the cost and complexity of modern aircraft systems increases, emphasis has been placed on model-based design as a means for reducing development cost and optimizing performance. To facilitate this, an appropriate modeling environment is required that allows developers to rapidly explore a wider design space than can cost effectively be considered through hardware construction and testing. This wide design space can then yield solutions that are far more energy efficient than previous generation designs. In addition, non-intuitive cross-coupled subsystem behavior can also be explored to ensure integrated system stability prior to hardware fabrication and testing. In recent years, optimization of control strategies between coupled subsystems has necessitated the understanding of the integrated system dynamics.

Future aircraft systems are projected to have order of magnitude greater power and thermal demands, along with tighter constraints on the performance of the power and thermal management subsystems. This trend has led to the need for a fully integrated design process where power and thermal systems, and their interactions, are considered simultaneously. To support this new design paradigm, a general framework for codifying and checking specifications and requirements is presented. This framework is domain independent and can be used to translate requirement language into a structured definition that can be quickly queried and applied to simulation and measurement data. It is constructed by generalizing a previously developed power quality analysis framework. The application of this framework is demonstrated through the translation of thermal specifications for airborne electrical equipment, into the SPecification And Requirement Evaluation (SPARE) Tool.

The performance of a more-electric aircraft (MEA) power system electrical accumulator unit (EAU) architecture consisting of a 57000 rpm induction machine (IM) coupled to a controllable shaft load and controlled using direct torque control (DTC) is examined through transient modeling and simulation. The simplicity and extremely fast dynamic torque response of DTC make it an attractive choice for this application. Additionally, the key components required for this EAU system may already exist on certain MEA, therefore allowing the benefits of EAU technology in the power system without incurring a significant weight penalty. Simulation results indicate that this architecture is capable of quickly tracking system bus power steps from full regenerative events to peak load events while maintaining the IM's speed within 5% of its nominal value.

This paper develops a model for a parallel microchannel evaporator that incorporates quality variation at the tube inlets and variable mass flow rates among tubes. The flow distribution is based on the equal pressure drop along each flow path containing headers and tubes. The prediction of pressure drop, cooling capacity, and exit superheat strongly agree with 48 different experimental results obtained in four configurations using R134a. Predicted temperature profiles are very close to infrared images of actual evaporator surface. When compared to the uniform distribution model (that assumes uniform distribution of refrigerant mass flow rate and quality) results from the new model indicate superior prediction of cooling capacity, and exit superheat. Model results indicate maldistribution of refrigerant mass flow rate among the parallel tubes, caused primarily by pressure drop in the outlet header.

Beginning flight students were taught landings in a flight simulator with a visual landing display to examine the effects of scene detail, visual augmented guidance, and the number of landing training trials. Transfer as assessed in a criterion simulator configuration showed advantages for larger numbers of training trials, visual augmented guidance, and moderate scene detail. Transfer of training to the aircraft showed advantages for low-scene detail over moderate-scene detail for the number of landing training sessions. Subjects who received equal simulator time practicing an instrument pattern (control group) performed better than the moderate-scene detail group on student assisted landings and number of landing training sessions.

An IPTMS hardware facility has been established in the laboratories of the Aerospace Systems Directorate of the Air Force Research Laboratory (AFRL) at Wright-Paterson Air Force Base (WPAFB). This hardware capability was established to analyze the transient behavior of a high power Electrical Power System (EPS) coupled virtually to a Thermal Management System (TMS) under fast dynamic loading conditions. The system incorporates the use of dynamic electrical load, engine emulation, energy storage, and emulated thermal loads operated to investigate dynamics under step load conditions. Hardware architecture and control options for the IPTMS are discussed. This paper summarizes the IPTMS laboratory demonstration system, its capabilities, and preliminary test results.

The interdependency between propulsion, power, and thermal subsystems on military aircraft such as the F-35 Joint Strike Fighter (JSF) and F-22 Raptor continues to increase as advanced war-fighting capabilities including solid-state radars, electronic attack, electric actuation, and Directed Energy Weaponry (DEW) expand to meet Air Force needs. Novel analysis and testing methodologies are required to predict these interdependencies and address adverse interactions prior to costly hardware prototyping. As a result, the Air Force Research Laboratory (AFRL) has established a dynamic hardware-in-the-loop (HIL) test-bed wherein transient simulations can be integrated through advanced real-time simulation with prototype hardware for integrated system studies and analysis. This paper details a test-bed configuration where a dynamic simulation of an aircraft turbine engine is utilized to control a dual-head electric drive stand.

Directed Energy weapon (DEW) systems are being developed for both ground and airborne applications. Typically, they consist of microwave or laser powered guns. Both the microwave application and the diode based laser applications require significant amount of power. This power ranges from several hundred kilowatts (kW) for microwave applications to Megawatts (MW) for laser applications. The laser application requires that the full power be available for short duration, typically 5 seconds, which could be repeated several times with short pauses in between. The control of a generator, which delivers Megawatt of the intermittent power greatly differs from the of normal steady state generator control. It poses significant challenges. Application of power (and for this matter its removal) is a transient phenomenon that takes time and its effects ripple through the whole system.

The Wireless Integrated Cockpit Information Display (WICID) program developed a method for pilots to remotely control and display carry-on laptop based applications from the aircraft cockpit. Because flight safety concerns do not allow the pilot/copilot to use the standard keyboard and mouse devices during flight, the WICID program developed a multifunction display (MFD) that uses customized input devices such as bezel keys and a touch screen. The subsequent design of the WICID system became especially valuable in enhancing certain technologies critical to the military cockpit. This paper will address how the WICID system topology is uniquely suited to improve cockpit access to four main technology categories: Enhanced Situation Awareness (SA), Mission Planning/On-board Replanning, Enhanced Communication, and Navigation Aids.

Aircraft power demands continue to increase with the increase in electrical subsystems. These subsystems directly affect the behavior of the power and propulsion systems and can no longer be neglected or assumed linear in system analyses. The complex models designed to integrate new capabilities have a high computational cost. Hardware-in-the-loop (HIL) is being used to investigate aircraft power systems by using a combination of hardware and simulations. This paper considers three different real-time simulators in the same HIL configuration. A representative electrical power system is removed from a turbine engine simulation and is replaced with the appropriate hardware attached to a 350 horsepower drive stand. Variables are passed between the hardware and the simulation in real-time to update model parameters and to synchronize the hardware with the model.

A primary challenge in performing integrated system simulations is balancing system simulation speeds against the model fidelity of the individual components composing the system model. Traditionally, such integrated system models of the electrical systems on more electric aircraft (MEA) have required drastic simplifications, linearizations, and/or averaging of individual component models. Such reductions in fidelity can take significant effort from component engineers and often cause the integrated system simulation to neglect critical dynamic behaviors, making it difficult for system integrators to identify problems early in the design process. This paper utilizes recent advancements in co-simulation technology (DHS Links) to demonstrate how integrated system models can be created wherein individual component models do not require significant simplification to achieve reasonable integrated model simulation speeds.

As aircraft continue to increase their power and thermal demands, transient operation of the power and propulsion subsystems can no longer be neglected at the aircraft system level. The performance of the whole aircraft must be considered by examining the dynamic interactions between the power, propulsion, and airframe subsystems. Larger loading demands placed on the power and propulsion subsystems result in thrust, speed, and altitude transients that affect the aircraft performance and capability. This results in different operating and control parameters for the engine that can be properly captured only in an integrated system-level test. While it is possible to capture the dynamic interactions between these aircraft subsystems by using simulations alone, the complexity of the resulting system model has a high computational cost.

Detailed machine models are, and will continue to be, a critical component of both the design and validation processes for engineering future aircraft, which will undoubtedly continue to push the boundaries for the demand of electric power. This paper presents a survey of experimental testing procedures for typical synchronous machines that are applied to brushless synchronous machines with rotating rectifiers to characterize their operational impedances. The relevance and limitations of these procedures are discussed, which include steady-state drive stand tests, sudden short-circuit transient (SSC) tests, and standstill frequency response (SSFR) tests. Then, results captured in laboratory of the aforementioned tests are presented.

Model based design is a standard practice within the aerospace industry. However, the accuracies of these models are only as good as the parameters used to define them and as a result a great deal of effort is spent on model tuning and parameter identification. This process can be very challenging and with the growing complexity and size of these models, manual tuning is often ineffective. Many methods for automated parameter tuning exist. However, for aircraft systems this often leads to large parameter search problems since frequency based identification and direct gradient search schemes are generally not suitable. Furthermore, the cost of experimentation often limits one to sparse data sets which adds an additional layer of difficulty. As a result, these search problems can be highly sensitive to the definition of the model fitness function, the choice of algorithm, and the criteria for convergence.

Future aircraft will demand a significant amount of electrical power to drive primary flight control surfaces. The electrical system architecture needed to source these flight critical loads will have to be resilient, autonomous, and fast. Designing and ensuring that a power system architecture can meet the load requirements and provide power to the flight critical buses at all times is fundamental. In this paper, formal methods and linear temporal logic are used to develop a contactor control strategy to meet the given specifications. The resulting strategy is able to manage multiple contactors during different types of generator failures. In order to verify the feasibility of the control strategy, a real-time simulation platform is developed to simulate the electrical power system. The platform has the capability to test an external controller through Hardware in the Loop (HIL).

Integrated system-level analysis capability is critical to the design and optimization of aircraft thermal, power, propulsion, and vehicle systems. Thermal management challenges of modern aircraft include increased heat loads from components such as avionics and more-electric accessories. In addition, on-going turbine engine development efforts are leading to more fuel efficient engines which impact the traditionally-preferred heat sink - engine fuel flow. These conditions drive the need to develop new and innovative ways to manage thermal loads. Simulation provides researchers the ability to investigate alternative thermal architectures and perform system-level trade studies. Modeling the feedback between thermal and engine models ensures more accurate thermal boundary conditions for engine air and fuel heat sinks, as well as consideration of thermal architecture impacts on engine performance.

The Air Force Research Laboratory (AFRL), in cooperation with the University of Dayton Research Institute (UDRI) and Fairchild Controls Corporation, is building a test facility to study the use of advanced vapor cycle systems (VCS) in an expanded role in aircraft thermal management systems (TMS). It is dedicated to the study and development of VCS control and operation in support of the Integrated Vehicle ENergy Technology (INVENT) initiative. The Two Phase Thermal Energy Management System (ToTEMS1) architecture has been shown through studies to offer potential weight, cost, volume and performance advantages over traditional thermal management approaches based on Air Cycle Systems (ACS). The ToTEMS rig will be used to develop and demonstrate a control system that manages the system capacity over both large amplitude and fast transient changes in the system loads.

Expansion work recovery by two-phase ejector is known to be beneficial to vapor compression cycle performance. However, one of the biggest challenges with ejector vapor compression cycles is that the ejector cycle performance is sensitive to working condition changes which are common in automotive applications. Different working conditions require different ejector geometries to achieve maximum performance. Slightly different geometries may result in substantially different COPs under the same conditions. The ejector motive nozzle throat diameter (motive nozzle restrictiveness) is one of the key parameters that can significantly affect ejector cycle COP. This paper presents the experimental results of the application of a new two-phase nozzle restrictiveness control mechanism to an automotive transcritical R744 ejector cycle.

Vapor compression systems (VCS) offer significant benefits as the backbone for next generation aircraft thermal management systems (TMS). For a comparable lift, VCS offer higher system efficiencies, improved load temperature control, and lower transport losses than conventional air cycle systems. However, broad proliferation of VCS for many aircraft applications has been limited primarily due to maintenance and reliability concerns. In an attempt to address these and other VCS system control issues, the Air Force Research Laboratory has established a Vapor Cycle System Research Facility (VCSRF) to explore the practical application of dynamic VCS control methods for next-generation, military aircraft TMS. The total refrigerant mass contained within the closed refrigeration system (refrigerant charge) is a critical parameter to VCS operational readiness. Too much or too little refrigerant can be detrimental to system performance.