Search Results

Ultrasonic spot welds were made between sheets of 0.8-mm-thick hot-dip-galvanized mild steel and 1.6-mm-thick AZ31B-H24. Lap-shear strengths of 3.0-4.2 kN were achieved with weld times of 0.3-1.2 s. Failure to achieve strong bonding of joints where the Zn coating was removed from the steel surface indicate that Zn is essential to the bonding mechanism. Microstructure characterization and microchemical analysis indicated temperatures at the AZ31-steel interfaces reached at least 344°C in less than 0.3 s. The elevated temperature conditions promoted annealing of the AZ31-H24 metal and chemical reactions between it and the Zn coating.

Boosted Homogeneous Charge Compression Ignition (HCCI) has been modeled and has demonstrated the potential to extend the engine's upper load limit. A commercially available engine simulation software (GT-PowerÖ) coupled to the University of Michigan HCCI combustion and heat transfer correlations was used to model a 4-cylinder boosted HCCI engine with three different boosting configurations: turbocharging, supercharging and series turbocharging. The scope of this study is to identify the best boosting approach in order to extend the HCCI engine's operating range. The results of this study are consistent with the literature: Boosting helps increase the HCCI upper load limit, but matching of turbochargers is a problem. In addition, the low exhaust gas enthalpy resulting from HCCI combustion leads to high pressures in the exhaust manifold increasing pumping work. The series turbocharging strategy appears to provide the largest load range extension.

This paper discusses the effects of stroke-to-bore (S/B) ratio on HCCI combustion. KIVA-3V, coupled with a multi-zone detailed chemical kinetics solver, is used to quantify the effects of changes in S/B ratio to heat transfer, thermal stratification and HCCI combustion. Three S/B ratios (0 5, 1.1 and 1.5) are analyzed. The results indicate that a cylinder with smaller S/B has more heat losses and lower thermal efficiency compared with a cylinder with larger S/B ratio, because of larger area-to-volume ratio near TDC. Moreover, the lowest S/B ratio case has a narrower temperature distribution before the onset of combustion. This leads to shorter burn duration, higher heat release rate and, consequently, increased knocking tendency. The emission results also favor the higher S/B ratio, with S/B=0.5 having the highest CO and HC emissions for relatively early combustion phasing; however, this trend is reversed as combustion is retarded.

Side impact field crashes from the University of Michigan Crash Injury Research and Engineering Network (UM CIREN) database were studied in detail. These cases involved seriously injured occupants that spanned 1997 - 2006 model year vehicles. Specific injury risks are not presented because the database used was populated only with occupants requiring treatment at a Level 1 Trauma Center. This study analyzes side impact collisions for AIS ≥ 3 injury patterns in crash configuration, injury contact locations, gender and by age. Field crashes were also categorized into those that represent existing standard side impact laboratory test methods. Over half of the cases were identified as collisions into the passenger compartment with occupants seated on the near side of the vehicle closest to the impact, which is consistent with current standard laboratory tests. The next two largest categories involved either far-side occupants or impacts primarily centered onto the engine compartment.

Failure mode of laser welds in lap-shear specimens of high strength low alloy (HSLA) steel is investigated in this paper. The experimental results from quasi-static tests show that the laser welds failed in a ductile necking/shear failure mode near the heat affected zone. In order to understand the failure mode of these welds, a finite element analysis under plane strain conditions was conducted to identify the effects of the different plastic behaviors of the base metal, heat affected zone, and weld metal on the ductile failure. The results of the finite element analysis show that the higher effective stress-plastic strain curves of the weld metal and the heat affected zone results in the necking/shear failure mode. The deformed shape of the finite element model near the weld matches well with that of a failed weld.

The number of control actuators available on spark-ignition engines is rapidly increasing to meet demand for improved fuel economy and reduced exhaust emissions. The added complexity greatly complicates control strategy development because there can be a wide range of potential actuator settings at each engine operating condition, and map-based actuator calibration becomes challenging as the number of control degrees of freedom expand significantly. Many engine actuators, such as variable valve actuation and flow control valves, directly influence in-cylinder combustion through changes in gas exchange, mixture preparation, and charge motion. The addition of these types of actuators makes it difficult to predict the influences of individual actuator positioning on in-cylinder combustion without substantial experimental complexity.

Flexible fuel vehicles (FFVs) are able to operate on a blend of ethanol and gasoline in any volumetric concentration of up to 85% ethanol (93% in Brazil). The estimation of ethanol content is crucial for optimized and robust performance in such vehicles. Even if an ethanol sensor is utilized, an estimation scheme independent of the ethanol sensor measurement retains advantages in enhancing the reliability of ethanol estimation and allowing on-board diagnostics. It is well-known that an exhaust gas oxygen (EGO) sensor could be utilized to estimate the ethanol content, which exploits the difference in stoichiometric air-to-fuel ratio (SAFR) between ethanol (9.0) and gasoline (14.6). The SAFR-based ethanol estimation has been shown to be prone to large errors with mass air flow sensor bias and/or fuel injector shift.