Search Results

Presented here are analyses and statistical summaries of data collected from 11,299 flight operations recorded on 6 BE-1900D aircraft during routine commuter service over a period of three years. Basic flight parameters such as airspeed, altitude, flight duration, etc. are shown in a form that allows easy comparison with the manufacturer's design criteria. Lateral ground loads are presented for ground operations. Primary emphasis is placed on aircraft usage and flight loads. Maneuver and gust loads are presented for different flight phases and for different altitude bands. In addition, derived gust velocities and various coincident flight events are shown and compared with published operational limits.

The work presented in this paper is part of a long-term research program to explore methods for improving bleed air system performance. Another objective of this research is to provide detailed experimental data for the development and validation of simulation tools used in the design and analysis of bleed air systems. A business jet wing was equipped with an inner-liner hot air ice protection system and was extensively instrumented for documenting system thermal performance. The wing was tested at the NASA Glenn Icing Research Tunnel (IRT) for representative in-flight icing conditions. Data obtained include bleed air supply and exhaust flow properties, wing leading edge skin temperatures, temperatures and pressures in the interior passages of the bleed air system, flow properties inside the piccolo tube, photos of run back ice shapes and ice shape traces. Selected experimental results for a warm hold icing condition are presented in this paper.

A methodology for developing spray rigs for icing cloud simulation is presented. This methodology includes Computational Fluid Dynamics (CFD) analysis and icing tunnel experiments and was applied to design a spray rig system for a small airborne icing tanker. An in-house spray system was developed and tested in a laboratory to assess two commercially available nozzles - a single-jet type and a multi-jet type - which were capable of producing both FAR Part 25 Appendix C and SLD icing clouds. Spray rig characteristics evaluated during the laboratory tests included air and water flow rates as well as droplet size and distributions. The effects of airspeed and nozzle spacing on spray plume size and uniformity were investigated in a small icing tunnel facility with a two-nozzle spray rig. The experimental data were compared with three-dimensional numerical simulation results obtained with the FLUENT software.

An experimental study was performed to investigate large droplet dynamics in the vicinity of an airfoil. The investigation was conducted using the NASA Glenn Droplet Imaging Flow Tunnel (DrIFT). Mono-dispersed large droplets were released at the tunnel inlet and accelerated toward an airfoil that was mounted in the test section. The dynamic behavior of a droplet's encounter with the airfoil, which may involve droplet distortion, break-up, impingement and splashing, was recorded using a high-speed imaging system. The effects of the droplet size, tunnel velocity and airfoil configuration on the droplet dynamics were investigated in a parametric study. The droplet sizes used in the experimental study were 96 and 375 μm whereas tunnel velocities were varied from 80 to 130 mph. Three different airfoil geometries were used in the experimental study; a ‘clean’ and ‘iced’ airfoil, and a ‘clean’ three-element high-lift airfoil. The incidence angle of these airfoils was set to zero degrees.

Ice particles shed from aircraft surfaces are a safety concern because they can damage aft-mounted engines and other aircraft components. Ice shedding is a random and complex phenomenon. The randomness of the ice fragment geometry, size, orientation and shed location in addition to potential particle breakup during flight poses considerable simulation challenges. Current ice shedding analysis tools have limited capabilities due to the lack of experimental aerodynamic coefficients for the forces and moments acting on the ice fragment. A methodology for simulating the shedding of large ice particles from aircraft surfaces was developed at Wichita State University. This methodology combines experimental aerodynamic characteristics of ice fragments, computational fluid dynamics, trajectory analysis and the Monte Carlo method to provide probability maps of shed particle footprints at desired locations.

Some of the methods used for experimental detection and examination of wake vortices are presented. The aim of the article is to provide the reader a brief overview of the available methods. The material is divided into two major sections, one dealing with methods used primarily in the laboratory, and the second part devoted to those used in field operations. Over one hundred articles are cited and briefly discussed.

An algorithm is developed and validated for automatic avoidance of restricted airspaces. This method is devised specifically for implementation with an advanced flight control system designed for general aviation application. The algorithm presented here implements two inputs to the aircraft; the bank angle, and the airspeed, while the control system always ensures coordinated maneuvers. Unlike collision avoidance systems, the current method is not designed to serve in an advisory role, but to assume complete control of the aircraft if necessary. It is demonstrated that in order to implement this technique, the aircraft must be assigned an immediate domain whose size would have to depend on the aircraft performance and flight conditions. The strategy is designed such that as the domain surrounding the aircraft approaches that of the restricted airspace, aircraft control would switch gradually away from the pilot and to the controller, which would initiate an evasive maneuver.

The necessity of avoiding the destructive and non-repeatable FSST (Full Scale Sled Test) makes it desirable to devise a cheaper and more repeatable method which can supplant this test procedure. This need developed the HCTD (HIC Component Testing Device) which is capable of providing conservative HIC results with higher repeatability. The computational model of the HCTD is validated against one of the tests conducted at CAMI with polyethylene foam. This validated model is used to conduct a series of tests with input parameters similar to the sled test to develop the correlation between the sled test and HCTD. This study hence concludes that a validated computational model of HCTD can be successfully utilized to address the HIC compliance issues for a foam padded surface.

Data obtained from digital flight data recorders are used to assess the actual operational environment of propellers on a fleet of Beech 1900D aircraft in commuter role. Information is given on various aerodynamic parameters as well as those pertaining to engine and propeller usage. The takeoff rotation has been identified as the most demanding phase of flight in terms of unsteady loads exerted on the propeller blades. Special attention is paid to ground operations.

Dynamic aircraft seat regulations are identified in the Code of Federal Regulations (CFR), 14 CFR Parts § 23.562 [1] and § 25.562 [2] for crashworthy evaluation of a seat in dynamic environment. The regulations specify full-scale dynamic testing on production seats. The dynamic tests are designed to demonstrate the structural integrity of the seat to withstand an emergency landing event and occupant safety. SAE standard AS 8049 [3] supports detailed information on dynamic seat testing procedure and acceptance criteria. Full-scale dynamic testing in support of certification is expensive and repeated testing due to failure drastically increases the expense. Involvement of impact environment, flexibility in interior configuration and complicated nature of seat engineering design makes this problem quite complex, so that classical hand calculations are practically impossible.

The current emphasis on environment protection by reducing noise pollution has led to stricter noise standards for general aviation aircraft. As a result, there is a growing demand for a computational tool to predict the noise during the design process. A computer program, called ProRAPP, has been developed for the prediction of noise generated by propeller/rotor blades. The acoustic pressure is calculated using a form of Ffowcs Williams-Hawkings equation which is suitable for numerical implementation. For noise predictions, the observer can either move with the propeller/rotor hub or it can be fixed to the ground. Experimental data from both wind tunnel and flight tests are used to validate the numerical results.

This paper presents experimental methods for investigating large droplet impingement dynamics and for obtaining small and large water droplet impingement data. Droplet impingement visualization experiments conducted in the Goodrich Icing Wind Tunnel with a 21-in chord NACA 0012 airfoil demonstrated considerable droplet splashing during impingement. The tests were performed for speeds in the range 50 to 175 mph and with cloud median volumetric diameters in the range of 11 to 270 microns. Extensive large droplet impingement tests were conducted at the NASA Glenn Icing Research Tunnel (IRT). Impingement data were obtained for a range of airfoil sections including three 36-inch chord airfoils (MS(1)-0317, GLC-305, and NACA 652-415), a 57-inch chord Twin Otter horizontal tail section and 22.5-minute and 45-minute LEWICE glaze ice shapes for the Twin Otter tail section. Small droplet impingement tests were also conducted for selected test models.

Global warming concerns are stimulating accelerated research and development of alternative fuels and propulsion systems for automobiles. The potential application of these emerging technologies to airplanes is reviewed. Preliminary designs of zero greenhouse gas emission airplanes using hydrogen fuel and either internal combustion or fuel cell-electric motor propulsion are presented for a wide body jet transport, medium jet transport, business jet, and single engine propeller airplane. The hydrogen fueled internal combustion engine airplanes offer the easiest path to zero emissions, but the greater efficiency of the fuel cell airplanes allows designs requiring substantially less fuel. The single engine propeller airplane is the easiest to modify for hydrogen fuel, because of the relatively high mass and volume of the engine being replaced. Technology improvements needed to make zero emission airplanes viable are suggested.

A unique cascade test facility has been developed for use in the Wichita State University (WSU) water table. Although small in scale, the WSU water table has the advantage of low cost and the ease with which test conditions can be varied. Water table facilities have been used in the past for cascade experiments, especially as analogies for compressible flow visualization of turbine cascades. However, the lack of a quantitative measurement technique at low speeds has precluded the use of the water table as an analogy for testing subsonic compressors and turbines. In the present experiment, the hydrogen bubble flow visualization technique is used to generate bubble time lines, and a CCD (Charge Coupled Device) video camera system captures and digitizes these time line images. A VisualBASIC® computer program is then used to determine the wake velocity profile based on the difference in bubble line positions at successive intervals of time.

The coupled influence of material configuration (number of facesheet plies, core density, core thickness) and impact parameters (impact velocity and energy, impactor diameter) on the impact damage resistance characteristics of sandwich composites comprised of carbon-epoxy woven fabric facesheets and Nomex honeycomb cores was investigated using empirically based quadratic response surfaces. The diameter of the planar damage area associated with TTU C-scan measurements and the peak residual facesheet indentation depth were used to describe the extent of internal and detectable surface damage, respectively. Estimates of the size of the planar damage region correlated reasonably well with experimentally determined values. For a fixed set of impact parameters, estimates of the planar damage size and residual facesheet indentation suggest that impact damage development is highly material and lay-up configuration dependent.

During this study, a number of 8.5-inch by 11.5-inch flat honeycomb sandwich panels were inflicted with low energy impact damage, inspected non-destructively, and tested for residual in-plane compressive strength. Each panel had either a 3/8-inch or 3/4-inch low density Nomex honeycomb core, and either 2-ply, 4-ply or 6-ply face sheets. The face sheets were either carbon or Eglass (prepreg) fabric. The panels were either clamped or simply supported in a test fixture during impact from a gravity assisted drop mechanism, and impacted with either a 1-inch or 3-inch diameter spherical indenter. After impact the damage to each panel was characterized by (1) ultrasonic through-transmission to obtain a c-scan representing planar damage area, (2) indentation volume and depth, and finally (3) visual inspection to rate the damage according to a predetermined rating scale. The panels were then tested for in-plane compressive strength.

An aging aircraft accumulates fatigue cracks commonly referred to as multiple site damage (MSD). A simplified engineering fracture mechanics model, generally referred to as the linkup model (or plastic zone touch model), has been used with some success to describe the MSD fracture phenomenon in 2024-T3 aluminum panels. A disadvantage of the linkup model is that it gives excessively inaccurate results for some configurations. A modified linkup model has been developed through empirical analysis of test data taken from unstiffened panels with MSD cracks at open holes. The modified linkup model was then validated with test data from stiffened panels including single-bay panels with the lead crack centered between stiffeners and two-bay panels with the lead crack centered beneath a severed stiffener. Further validation of the modified linkup model was done with test data from panels with bolted lap joints. Test results were obtained from 112 different panels.

This paper presents the experimental study of hole quality parameters in the drilling of titanium alloy (6Al-4V). Titanium alloy plates were drilled dry using three types of solid carbide drills i.e. 2-flute helical twist drill, straight flute and three-flute drill. The objective was to study the effects of process parameters like feed rate, speed and drill bit geometry on the hole quality features. Typical hole quality features in a drilling process are the hole quality measures such as surface roughness, hole diameter, hole roundness and burr height. The results indicate that proper selection of speed, feed rate, and drill geometry can optimize metal removal rate and hole quality.

The competitive market has forced the industry to develop methodologies to reduce lead-time of the products without sacrificing quality. One of the major metal removal operations in the aerospace industries is drilling. Over 100,000 holes are made for a small single engine aircraft. Naturally, demand for faster production rate results in the demand for high-speed drilling. But the cost of hole-making operations becomes a significant portion of the total manufacturing cost. This paper discusses the high speed drilling of Al-2024-T3 alloy, the effect of feed and speed on hole quality features like oversize, roundness error, burr height and surface roughness.

Metal cutting is a substantial constituent of airframe manufacturing. During the past several decades, it has evolved significantly. However, most of the changes and improvement were initiated by the machine tool industry and cutting tool industry, thus these new technologies is generally applicable to all industries. Among them, few are developed especially for the airframe manufacture. Therefore, the potential of high efficiency could not be fully explored. In order to deal with severe competition, the aerospace industry needs improvement with a focus on achieving low cost through high efficiency. The direction of research and development in parts machining must comply with lean manufacturing principles and must enhance competitiveness. This article is being forwarded to discuss the trend of new developments in the metal cutting of airframe parts. Primary driving forces of this movement, such as managers, scientists, and engineers, have provided significant influence to this trend.