Search Results

This paper proposes a novel engine starter system composed of a small-power electric motor and a simple mechanical valve train. The system makes it possible to design more efficient starters than conventional systems, and it is especially effective to restart engines equipped with idling stop systems. Recently, several idling stop systems, having intelligent start-up functions and highly-efficient generate capabilities have been proposed for motorcycles. One of challenges of the idling stop systems is the downsizing of electric motors for starting-up. However, there are many limitations to downsize the electric motors in the conventional idling stop systems, since the systems utilize the forward-rotational torque of the electric motors to compress the air-fuel mixture gas in the cylinders. Our studies exceeded the limitations of downsizing the electric motors by mainly using the engine combustion energy instead of the electric energy to go over the first compression top dead center.

The improvement of fuel consumption is the most important issue for engine manufactures from the viewpoint of energy and environment conservation. A piston-cylinder system plays an important role for the reduction of an engine friction. For the improvement of the frictional behavior of the piston-cylinder system, it is beneficial to observe and analyze the frictional waveforms during an engine operation. To meet the above-mentioned demand, frictional waveforms were measured with using the renewed floating liner device. In the newly developed floating liner device, an actual cylinder block itself was used as a test specimen. The measured single cylinder was an aluminum monolithic type made of hypereutectic Al-17%Si alloy using a high pressure die casting process. The combined piston was a light weight forged piston and a DLC coated piston ring was used. For the measurement, 110cc air cooled single cylinder engine was used.

Gasoline fueled Homogeneous Charge Compression Ignition (HCCI) combustion with internal exhaust gas re-circulation using Negative Valve Overlap (NOL) was investigated by means of calculation and experiment in order to apply this technology to practical use with sufficient operating range and with acceptable emission and fuel consumption. In this paper we discuss the basic characteristics of NOL-HCCI with emphasis on the influence of intake valve timing on load range, residual gas fraction and induction air flow rate. Emission and fuel consumption under various operation conditions are also discussed. A water-cooled 250cc single cylinder engine with a direct injection system was used for this study. Three sets of valve timing were selected to investigate the effect of intake valve opening duration. Experimental results demonstrated that an engine speed of approximately 2000rpm yields an NMEP (Net Mean Effective Pressure) range from 200kPa to 400kPa.

Regarding S.I. gasoline engine, it is one of the most important matters to eliminate cyclic variation of combustion. Especially with high compression ratio and high boosted engine, the difficulties increase more. This paper describes the analysis of combustion process precisely by using many ion-current probes and CFD with the unique approaches. The number of used ion-current probes is 80 and they are mounted on whole combustion chamber wall especially including moving intake and exhaust valve faces. Thus cyclic variations of flame propagation can be measured precisely under high compression ratio and high boosted conditions in a multi-cylinder engine. In addition, CFD combustion simulation is conducted through full four strokes of continuous nine cycles. Moreover air motion and pressure vibration in intake and exhaust manifolds in whole cycles are considered. These unique approaches have made CFD result correspond to the measurement result of cyclic variations of actual combustion.

In this study, lean combustion concept was investigated to realize better Fuel Economy (FE) on a single cylinder motorcycle engine. A low-pressure direct injection (DI) system was applied to realize lean stratified combustion concept with good combustion stability. In addition, Exhaust Gas Recirculation (EGR) system applicable to small motorcycle engines was used to attain FE improvement and NOx reduction. EGR gas temperature and EGR return position were focused on and effects on FE and NOx were investigated. Computational Fluid Dynamics (CFD) was used to reveal EGR distribution and air motion in both the intake port and the cylinder. As a result, the influence of the stratified charge, EGR temperature and EGR return position on FE and NOx were explained quantitatively. These techniques were effective in reducing NOx and improving FE for a single cylinder motorcycle engine.

Combustion phenomena inside the actual Gasoline-Direct-Injection (GDI) engines have been drawing high attention to its emission characteristics as well as its potential to deal with ultra lean mixture. Although the detailed observation is necessary for its improvement, combustion visualization seems to be strangely overlooked for some reason. This study focuses on the direct observation of GDI combustion to clarify the difficulties behind GDI concept by using a test engine of an actual “wall-guided” configuration and by comparing GDI spray quality with diesel spray in a high-pressure constant volume bomb. The results show that some of the problems about GDI combustion seem to be rather essential than easily conquered, which suggests the necessity for another combustion concept.

The in-cylinder flow, mixture distribution, combustion and exhaust emissions in a research, five-valve purpose-built gasoline engine are discussed on the basis of measurements obtained using laser Doppler velocimetry (LDV), fast spark-plug hydrocarbon sampling, flame imaging and NOx/HC emissions using fast chemiluminescent and flame ionisation detectors/analysers. These measurements have been complemented by steady flow testing of various cylinder head configurations, involving single- and three-valve operation, in terms of flow capacity and in-cylinder tumble strength.

Reduction in the cycle-to-cycle variation (CCV) of combustion in internal combustion engines is required to reduce fuel consumption, exhaust emissions, and improve drivability. CCV increases at low load operations and lean/dilute burn conditions. Specifically, the factors that cause CCV of combustion are the cyclic variations of in-cylinder flow, in-cylinder distributions of fuel concentration, temperature and residual gas, and ignition energy. However, it is difficult to measure and analyze these factors in a production engine. This study used an optically accessible single-cylinder engine in which combustion and optical measurements were performed for 45 consecutive cycles. CCVs of the combustion and in-cylinder phenomena were investigated for the same cycle. Using this optically accessible engine, the volume inside the combustion chamber, including the pent-roof region can be observed through a quartz cylinder.

Mixture formation is one of the most important factors for the combustion in the spark ignition engine with port fuel injection. The relation between combustion and mixture quality, however, is not quantitatively well established. In this study, the connection of combustion and mixture formation was explored with various measurement techniques. Borescopes were used in order to investigate the flame propagation in the combustion chamber and behavior of spray and fuel film on the wall in the intake port. For the purpose of investigation on the effect of mixture formation, various port fuel injection systems and parameters were tested and compared: direction, timing, and size of droplet. An SI engine for small vehicle was used under condition of 4 000 rpm. The investigation by images obtained has shown that inhomogeneity of mixture causes low combustion stability, especially due to direct introduction of fuel droplets into the combustion chamber.

A periodic impulsive sound at idle is occasionally described as ‘disagreeable’ in two-stroke engines. The relation between combustion conditions, piston vibrations, and the disagreeable sound is analyzed to clarify the phenomena. Some means to alleviate disagreeable sound are then proposed through stabilized combustion, high rigidity sound transfer systems, and refined skirt profiles. Experimental results are shown for the effects on main three factors evaluating disagreeable sound-loudness, impulsiveness, and frequency characteristics. In addition, piston behavior is measured, and the relation between piston motion and disagreeable sound is discussed in this paper.

We compared motoring friction loss, output performance at WOT (wide open throttle) and specific fuel consumption of big-end bearings on engines having identical specifications between the case of using plain bearings and rolling bearings to investigate the effect of the lubricating oil supply rate on these parameters in an attempt to improve output through reduction of friction loss for big-end bearings of small, high-output motorcycle engines. Testing was performed using a 125 cc, 4-cycle, single cylinder engine at high engine speeds mainly above 10,000 rpm.

Any improvements of the fuel economy with engines are always required for all petroleum fuel vehicles. The goal of such improvements must lead to reduce fuel consumption of the engines. However it may cause some deterioration with riding feeling that is one of the most important characteristics of the motorcycles. Yamaha has developed the strong hybrid motorcycle "HV-X"(hereafter the motorcycle). The motorcycle consists of a 4-stroke 250 cm₃ a cylinder engine and two 300V AC motors with a planetary gear set. The motorcycle reduces fuel consumption without severe influence onto the drive performance by utilizing the electric power.

In this study, an improvement of fuel consumption by changing the exhaust timing of a two-stroke engine has been made. The study results revealed that a remarkable improvement of fuel economy is possible by controlling the exhaust timing according to the engine speed. The reason for the better fuel economy was clarified through an analysis of exhaust gases, theoretical cycle calculations, and an analysis of combustion pressure. As an example of actual application, the results of tests made on an engine equipped with Yamaha power Valve System (YPVS), which is a variable exhaust timing mechanism using a tabor-shaped valve, will also be discussed.

Abnormal valve gear vibration is a perennial problem confronting the designer of high-performance 4-stroke engines. It would shorten time and reduce costs if an analytical method could be applied to the prediction of engine valve behavior. This paper describes a method of valve motion simulation for both SOHC and DOHC valve gears through interactive calculation and using computer graphics. The authors tried to set up as simple a simulation model as possible by using modal analysis and modeling techniques. Through setting simulation model parameters and experimental damping factors, a close correlation between calculated and actually measured results was found.

THE MULTI-VALVE FOUR STROKE CYCLE engine design trend is Coward increased engine power and higher fuel efficiency. While a four-valve system is the most common direction, problems occur when the valve area is widened by increasing the cylinder bore for a higher engine output. The layout of four larger valves causes the combustion chamber shape to flatten and the combustion time period to increase. In pursuit of the optimum multi-valve engine we have studied four, five, six and seven-valve per cylinder design. Performance targets and design constraints led us toward the successful five-valve engine technology. This technology develops high engine torque and efficient combustion over a wide range of engine speeds.

In order to obtain more reduction of two-stroke motorcycle engine noise than usual, it becomes necessary to make improvements within the combustion process itself. This study was carried out for two objectives. One is the investigation of the relationship between combustion and noise, and the other one is the development of noise reduction techniques. As the result, it was discovered that there was a significant correlation between engine noise and (dP/dθ)max, called the maximum rate of cylinder pressure rise. Therefore, the reduction of the (dP/dθ) max was recognized to be effective for engine noise reduction. The optimized alteration of combustion chamber shape is the most effective noise reduction technique, because it is able to reduce (dP/dθ) max without any sacrifice of engine power. In fact, the level of noise reduction can be predicted by one of the parameters obtained from the combustion chamber shape.

With emergence of fuel cells which have much better thermal efficiency than internal combustion engines (later abbreviated as ICE), ICE has to improve its thermal efficiency to the level of 50%. One of the ways to improve the thermal efficiency of ICE is to utilize ultra-lean combustion and several technical papers have been published. But it seems the thermal efficiency has not been improved as the theory predicts. The test data of these technical papers were re-examined and it was concluded that the thermal dissociation of burned gas and NOx formation is the key factor of a discrepancy between the theory and the actual test data. In order to prevent an occurrence of thermal dissociation, emulsified fuels (mixture of carbonaceous fuels with water) was proposed.

In the past, the performance of motorcycle engines has improved quite rapidly through intensive competition in racing and in the marketplace. Motorcycle engines have contributed to the technological progress of internal combustion engines (hereafter abbreviated as ICE). Today's environmental concerns require motorcycle engines to improve fuel economy and exhaust emission pollutants. After examination of potential measures to improve the thermal efficiency of small engines, it was concluded that if engineers of motorcycle engines fail to take on new ideas such as those being developed in cold fusion, it is foreseen that motorcycle engines will be replaced with new power plants as was seen on locomotives in the past.

A direct injection system in which fuel was injected through the cylinder wall was developed and detailed investigation was made for the purpose of reducing short-circuit of fuel in 2-stroke engines. As a result of dynamo tests using 430cc single cylinder engine, it was found that the injector was best attached at a location as close to TDC as possible on the rear transfer port side, and that the entire amount of fuel should be injected towards the piston top surface. Emissions were worsened if fuel was injected towards the exhaust port or spark plug. Although the higher injection pressure resulted in large emissions reduction effects, it did not have a significant effect on fuel consumption. When a butterfly exhaust valve, known to be effective against irregular combustion in the light load range, was applied, it was found to lead to further reductions in HC emission and fuel consumption while also improving combustion stability.

The demands on internal combustion engines for low emissions and fuel consumption are increasing year by year. On the other hand, engines to be used in motorcycles need to provide high output and quick response to meet user desire. In order to realize low fuel consumption while keeping high performance, it is necessary to properly understand cyclic variations during combustion as well as the influence of the injection system on fuel control during transient periods. The current paper reports on the results of a study in the influence of port fuel injection on combustion stability in a small displacement motorcycle engine, using both a series of experiments and CFD. The parameters of the injection systems under study are: (1) injection targeted area, (2) injection timing, and (3) fuel droplet size. The results of the current study show that injection aimed at the upstream wall yielded the best combustion stability.