Search Results

Thermodynamic characteristics of premixed compression ignition combustions were clarified quantitatively by heat balance estimation. Heat balance was calculated from temperature, mole fractions of intake and exhaust gases, mass and properties of fuels. Heat balance estimation was conducted for three types of combustion; a conventional diesel combustion, a homogeneous charge compression ignition (HCCI) combustion; fuel is provided and mixed with air in an intake pipe in this case, and an extremely early injection type PREmixed lean DIesel Combustion (PREDIC). The results show that EGR should be applied for premixed compression ignition combustion to complete combustion at lower load conditions and to control ignition timing at higher load conditions. With an application of EGR, both HCCI and PREDIC showed low heat loss characteristics at lower load conditions up to 1/2 load.

HCCI (Homogeneous Charge Compression Ignition) combustion results in very low NOx emissions, however, it is not without problems. One of them is that the heavy load operation range is limited by knock, due to an exceptionally high heat release rate. Knock increases the heat loss to the cylinder walls and piston, reducing thermal efficiency. To help solve these problems, direct (in-cylinder) water injection has been suggested to lower the local temperatures that seem to cause knock in HCCI. Water injection was adapted in an HCCI engine fueled with DME and Propane. Results showed that the indicated thermal efficiency was improved by about 2% (λ = 3.0, NA), and the operation range was expanded from 460kPa to 700kPa (NA) maintaining a low NOx level.

Premixed Lean Diesel Combustion (PREDIC) has very low NOx combustion because of early injection timing, for example, at -120 degrees ATDC; however, it has some problems. One problem is that so much fuel spray reaches the cylinder wall, which causes high HC emission and high fuel consumption. The other problem is that compression ignition timing control is difficult due to the dependence on the in-cylinder temperature. To solve these problems, an impingement spray system with two nozzles is attempted to obtain the spray increasing at the center of the combustion chamber instantaneously. This impingement spray system has two nozzles, which are located diagonally. Two sprays, one injected from each side injector, impinge each other at the center of the cylinder to create an air-fuel mixture.That is,this impingement spray system creates the air-fuel mixture by using the penetration of both sides of the sprays instead of early timing injection.

One of the problems in HCCI combustion is a knocking in higher load conditions. It governs the high load limit, and it is suggested that the knock increases heat loss[1], because it breaks the thermal boundary layer. But it is not clear how much knock affects on heat loss in the HCCI combustion in various conditions, such as ignition timing and load. The motivation of this study is to clarify the ratio of heat loss caused by knock in HCCI engines. The heat loss from zero-dimensional calculations with modified heat transfer coefficient, which is considering the effect of knock by adding a term of cylinder pressure rising rate dp/dt, agreed well with the results from the thermodynamic analysis in various conditions. And the results show that it is possible to avoid heat loss by knock by controlling the ignition timing at appropriate timing after T.D.C. and it will be possible to expand the load range if knock can be avoided.

Reduction of exhaust emissions and BSFC was studied for high pressure, wide range, and high EGR rates in a Super-clean Diesel six-cylinder heavy duty engine. The GVW 25-ton vehicle has 10.52 L engine displacement, with maximum power of 300 kW and maximum torque of 1842 Nm. The engine is equipped with high-pressure fuel injection of a 200 MPa level common-rail system. A variable geometry turbocharger (VGT) was newly designed. The maximum pressure ratio of the compressor is about twice that of the previous design: 2.5. Additionally, wide range and a high EGR rate are achieved by high pressure-loop EGR (HP-EGR) and low pressure-loop EGR (LP-EGR) with described VGT and high-pressure fuel injection. The HP-EGR can reduce NOx concentrations in the exhaust pipe, but the high EGR rate worsens smoke. The HP-EGR system layout has an important shortcoming: it has great differences of the intake EGR gas amount into each cylinder, worsens smoke.

Reduction of exhaust emissions and BSFC has been studied using a high boost, a wide range and high-rate EGR in a Super Clean Diesel, six-cylinder heavy duty engine. In the previous single-turbocharging system, the turbocharger was selected to yield maximum torque and power. The selected turbocharger was designed for high boosting, with maximum pressure of about twice that of the current one, using a titanium compressor. However, an important issue arose in this system: avoidance of high boosting at low engine speed. A sequential and series turbo system was proposed to improve the torque at low engine speeds. This turbo system has two turbochargers of different sizes with variable geometry turbines. At low engine speed, the small turbocharger performs most of the work. At medium engine speed, the small turbocharger and large turbocharger mainly work in series.

The 1997 Kyoto protocol came into effect in February, 2005 to reduce greenhouse gases within the period 2008-2012 by at least 5 % with respect to 1990 levels. Application of biodiesel fuel (BDF) to diesel engine is very effective to reduce CO2 emission, because BDF is carbon neutral in principle. The purpose of this project is to produce a light-duty biodiesel truck which can be suitable for emission regulation in next generation. The effect of BDF on the performance and emissions of modern diesel engine which was equipped with the aftertreatment for PM and NOx emissions was investigated without modifications of engine components and parameters, as a first step for research and development of biodiesel engine. Rapeseed oil methyl ester (RME) was selected in behalf of BDF, and combustion characteristics, engine performance and exhaust emissions were made a comparison between RME and petroleum diesel fuel by steady operation and Japan transient mode (JE05) tests.