Search Results

For the reduction of greenhouse gas emission in the transportation sector, various countermeasures against CO₂ emission have been taken. The eco-driving has been paid attention because of its immediate effect on the CO₂ reduction. Eco-driving is defined as a driving method with various driving techniques to save fuel economy. The eco-driving method has been promoted to the common drivers as well as the drivers of carriers. Additionally, there are many researches about improvement of fuel efficiency and CO₂ reduction. However, the eco-driving will have the reduction effect of CO₂ emission, the influence of the eco-driving on air pollutant emission such as NOx is not yet clear. In this study, the effect of the eco-driving on real-world emission has been analyzed using the diesel freight vehicle with the on-board measurement system.

An on-board measurement system that simultaneously measures road traffic, vehicle running conditions and exhaust emissions was installed in a diesel freight vehicle with two tons payload. Actual NOx mass emissions were compared with that measured in a typical test mode for urban cities on a chassis dynamometer. The frequency of vehicle accelerations in actual urban cities was found to exceed that of a typical test mode for urban cities on a chassis dynamometer, which resulted in increased NOx from actual running conditions compared with the typical test mode for urban cities. The dynamics of NOx emissions at an actual roadside was also analyzed. It was observed that NOx emission based on distance with an actual city route test was about two times higher than that of a free way route and a typical test mode for urban cities. The reason for high NOx with the city route was explained by the higher frequency of lower gears at which higher NOx is emitted.

The thermal efficiency of a spark-ignition (SI) engine must be improved to reduce both environmental load and fuel consumption. Although lean SI engine operation can strongly improve thermal efficiency relative to that of stoichiometric SI operation, the cycle-to-cycle variation (CCV) of combustion increases with the air dilution level. Combustion CCV is caused by CCVs of many factors, such as EGR, spark energy, air-fuel ratio, and in-cylinder flow structure related to engine speed. This study focuses on flow structures, especially the influence of a tumble structure on flow fluctuation intensity near ignition timing. We measured the flow field at the vertical center cross section of an optically accessible high-tumble flow engine using time-resolved particle image velocimetry. There are many factors considered to be sources of CCV, we analyzed three factors: the intake jet distribution, distribution of vortex core position and trajectory of the fluid particle near the spark plug.

HCCI (Homogeneous Charge Compression Ignition) engine is expected to a new engine to be high efficiency and low emission. But it is difficult to control ignition timing and combustion duration, because ignition and combustion mainly depend on oxidation process of fuel. In this study, the focus is to clear the combustion mechanism of auto-ignition engine. By calculating chemical kinetics of elementary reactions, effects of compression speed, equivalence ratio, initial temperature and compression ratio on auto-ignition were investigated. And also, behaviors of chemical species under auto-ignition process were cleared.

Auto-ignition, which is observed in homogeneous and premixed charge compression ignition engines, allows expansion of the lean flammability limit of engine operation and realization of stable ignition and combustion over a range of ultra-lean conditions, where NOx emissions are very low. In this study, the basic combustion mechanism of auto-ignition and combustion was studied with initial mixture temperatures and compression speeds for n-butane and dimethyl ether. A single-mode type heat release process was observed with n-butane in the homogeneous charge compression ignition test engine.

ATAC (Active Thermo-Atmosphere Combustion) is autoignition combustion in two stroke engines, which occurs by diluting trapped Fuel-Air mixture with residual gas to maintain a high temperature at low load operation. In this study, two-stroke ATAC engine testing was carried out to obtain fundamental knowledge for controlling the autoignition and combustion characteristics in this premixed charge compression-ignition combustion engine. The influences of delivery ratio, equivalence ratio and enginespeed (i.e. compression speed) on autoignition timing, autoignition temperature and combustion duration were investigated. It was found that the ATAC autoignition temperature and combustion duration did not depend on the delivery ratio and equivalence ratio, but were determined by the individual fuel characteristics. Increasing the compression speed reduced the ATAC autoignition temperature a little.

A simulation study was conducted to examine the transition from SI combustion to HCCI combustion in a two-stroke free piston engine fuelled with propane. Operation of the free piston engine was simulated based on the combination of three mathematical models including a dynamic model, a linear alternator model and a thermodynamic model. The dynamic model included an analysis of the piston motion, based on Newton's second law. The linear alternator model included an analysis of electromagnetic force, which was considered to be a resistance force for the piston motion. The thermodynamic model was used to analysis thermodynamic processes in the engine cycle, including scavenging, compression, combustion, and expansion processes. Therein, the scavenging process was assumed to be a perfect process. These mathematical models were combined and solved by a program written in Fortran.